Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Detailing and Interior

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 04-28-1999, 06:30 PM
Steve
Guest
 
Posts: n/a
I'm already a huge fan of your site and message boards. Kudos--your site is terrific!

When I took delivery of my CLK last April (98) I noticed some silver overspray on the drivers door sill plastic, seat, and steering wheel. The dealer of course removed it, end of story. Yesterday, while washing my beauty, I noticed a very slight depression in the hood (i.e., small dent). I'm sure this was there from the beginning, but never noticed it because it's hard to see unless you look from the right angle in the right light. Also, there's a slight imperfection--almost like a tiny indent (about 1/8 inch in diameter) in the paint where the dent is. I'm wondering if the car was repaired before I ever took delivery of it? Now that it's there, it's hard for me to enjoy the car! It appears to be over an area on the hood where there is a support underneath--making access tough. Do you think a paintless dent removal is possible? Do I need to have the entire hood repainted? GASP!

Thanks in advance,
SR

------------------
Steve
Reply With Quote
  #2  
Old 04-28-1999, 07:03 PM
Lee Scheeler
Guest
 
Posts: n/a
Thanks for the compliments Steve.

I would be very unhappy with the overspray situation. The amount of trade in that could be deducted for any paintwork or especially a repaint of the hood would hurt the value. If it were my "new" car I would likely go back to the dealership and be after blood. Perhaps there was an incedent in shipping that caused them to have to do a bit of paint work. If so they should at least ethically, if not legally, of declared it and given you an appropriate price break. Go to them and pursue some kind of compensation. I would avoid a hood repaint at all costs. Some place like "Fixx-a-dent" http://www.fixx-a-dent.com Or any other reputable paintless dent removel specialist should suffice. There is no excuse for a brand new car from a dealer that isn't brand new.

Good Luck...Lee
Reply With Quote
  #3  
Old 05-01-1999, 10:09 AM
Bob I
Guest
 
Posts: n/a
Steve:

I have used a dent removal company with good results. My 1998 E320 was parked under a tree last summer (Never do that if you can help it) and either something fell on the left front fender or it was caused by vandalism. There was about a 1" long crease that was quite noticeable, but no paint damage. They worked on it about 45 minutes at the dent removal company and you can not tell where the original dent was. Generally, if they can get at the back side of the dent it can be fixed. If you go this route, I would check with your Mercedes dealer to find out who they use. I then would ask the dent removal company to assign the BEST technician they have to your car.
Reply With Quote
  #4  
Old 05-02-1999, 05:01 PM
olc
Guest
 
Posts: n/a
I have had dents removed by a local person who primarily works for delaers and car rental agents. Charges $50 per panel and is remarkable. He can remove dents that DentBuster told me they couldn't get out. For inaccesssible panels, he can get out dents if you allow him to make a 1/8" hole (which get sealed when done)to insert a tool.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
What are the Chances of Dent Removal ? BAd124 Detailing and Interior 19 02-08-2005 09:14 PM
I dropped a small snap ring in my transmission --can I leave it? 83 240D Carrameow Diesel Discussion 8 12-09-2003 01:04 AM
I dropped a small snap ring in my transmission --can I leave it? 83 240D Carrameow Tech Help 6 12-08-2003 11:19 AM
3.0 Cyl Head Removal Question - Guide rail Locating Pin removal CE4me Tech Help 4 10-29-2003 06:44 PM
Argh! #@*$&#@ Repair advice needed Zeus Tech Help 14 02-21-2002 02:34 PM



All times are GMT -4. The time now is 02:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page