Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Detailing and Interior

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-28-2001, 09:06 PM
Chris17H
Guest
 
Posts: n/a
Question Engine Detailing...

Hey i have this old 1987 300E that my dad gave me, and he did not take care of keeping the engine area clean. So i bought this product saying all you do it spray it with it and let it sit for 10min, but then it says to spray your treated areas with water. Now i know that water can be in the engine but soaking the engine compartment just sounds kinda damaging. So all i need to know is if i can spray it with water and should i cover all the electrical componets, and with what?

Thank You

Reply With Quote
  #2  
Old 11-28-2001, 09:53 PM
tsgtchew
Guest
 
Posts: n/a
Keep engine running.

If you spray water on your engine, you must start the engine, spray with water, and than let the engine run for 10 or 15 minutes. Gary
Reply With Quote
  #3  
Old 11-30-2001, 12:10 PM
G-Benz's Avatar
Razorback Soccer Dad
 
Join Date: Apr 2001
Location: Dallas/Fort-Worth
Posts: 5,711
This topic has been discussed a number of times, but the basic premise is to make sure to protect the electricals from excess water, especially the distributor and spark plug holes where water can pool (depending on engine configurations).

Take note of how MB places components throughout the engine compartment before you begin. Most are located far from the engine to reduce deterioration from heat, but also shielded from rainwater and such.

Most components can sustain a bit of water, given that they are designed to reside in hostile temperature extremes, but not designed to take direct hits from concentrated jets of water.

As mentioned earlier, do run the engine immediately after.

You will be able to do this pretty safely if you don't go at it with a high-pressure hose (like at the car wash bays)...these can characteristically cause water to seep into areas the engine (and its components) won't particularly care for.

If you DO manage to drown one or more of the engine management systems, error codes may get thrown at the diagnostic module. Disconnecting the ground lead from the battery for a few minutes will allow the systems to reboot...don't do this unless you already know your radio security code though...

...BTW...don't do this on a HOT engine!!! Unless you like to replace cracked heads and blocks...

__________________
2009 ML350 (106K) - Family vehicle
2001 CLK430 Cabriolet (80K) - Wife's car
2005 BMW 645CI (138K) - My daily driver
2016 Mustang (32K) - Daughter's car
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Oil Additives Bill Wood Mercedes-Benz Performance Paddock 6 08-24-2011 10:53 AM
noisy engine Hocky Tech Help 0 02-28-2004 08:39 PM
Engine rpm = long life. Torque = fuel mileage and acceleration dabenz Diesel Discussion 1 04-26-2002 05:43 PM
Detailing Engine Question LarryO Detailing and Interior 1 08-10-2001 11:43 AM



All times are GMT -4. The time now is 03:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page