|
|
|
#1
|
|||
|
|||
Hard Shifting after work on car
I recently finished some work on my SDL and now the Tranny is shifting with hard shifts instead of the smooth changes previously.
Here's what I did, and yes I know some of these cannot be related to the Tranny: - Replaced Vacuum Pump (Original flat face was working fine - I think) - Fixed Exhaust Leak at front/rear manifold joint. - Drained & Flushed Cooling System & replaced top & bottom hoses. - Replaced Alternator Brushes/Regulator. - Removed EGR Valve (previously disabled) and associated vacuum hoses. - Cleaned out crossover pipe and installed new gaskets & seals. - Replaced all filters (air, fuel & oil) and oil. Anybody have any ideas??
__________________
1991 M-B 560SEL Arctic White/Grey 99,000 Miles 1987 M-B 300SDL Ivory/Palomino 229,000 Miles (sold but never forgotten) 2006 Volvo XC70 Blue/Beige 1999 Porsche Boxster Arena Red/Savanna Beige 1986 Porsche 928S Goldweiss/Brown Last edited by Dervman; 02-08-2005 at 06:11 PM. |
#2
|
|||
|
|||
Lack of vacuum = Hard shift
Look for the loose/leaking vacuum line or fitting, probably bumped, loosened or broken as you worked on the engine.
Follow the vacuum line from the brake booster source line ahead of the check valve, to the proportioning valve on the injection pump, back to the blue vacuum amplifier on the driver's side fender, through the switchover valve and finally down to the transmission vacuum modulator. Low/no vacuum = higher shift pressure = harder shifts. Best Regards, Jim |
#3
|
|||
|
|||
Thanks Jim, I'll check out the vacuum system.
I did move a bunch of stuff around when I was removing the vacuum lines to the EGR valve solenoids. It looks like on my SDL the small line from the vacuum pump goes to a 4-way connector and then there is a line to the proportioning valve on the injection pump, then over to the blue amplifier then the changeover switch (square top unit on bulkhead?) and then I guess to the transmission vacuum modulator. Where is the vacuum modulator located ? |
#4
|
|||
|
|||
Modulator is at the end of the vacuum line!
It's on the side of transmission. You probably didn't disturb it, since you weren't under the car. Best Regards, Jim |
#5
|
|||
|
|||
I checked all the lines and they seemed OK except for one that broke when I flexed it - now replaced. I think the problem may be the 4-way connector above the vacuum pump. I moved the vac lines that go in/out of this connector and the shifting seems better although not quite as smooth as I remember.
Now I find I have no heat to the footwells in the car I have to believe these things are related as it was working fine before the work I did. I'm not quite sure where to start. Defrost and side vents work OK but Centre vents seem dead also. Could low vacuum be affecting the ACC ? I'm leaving for Florida tomorrow (driving down) and running out of time. The good wife will not appreciate cold tootsies if I can't fix it. HELP !!! |
#6
|
||||
|
||||
Yes, the doors that direct airflow are vacuum actuated. So concentrate on tracking down all the vacuum leaks.
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#7
|
||||
|
||||
Any of the 3 or 4 way rubber couplers that the hose fit into without great effort should be replaced....new ones are VERY tight fit. Loose fit = vacume leaks.........
__________________
Proud owner of .... 1971 280SE W108 1979 300SD W116 1983 300D W123 1975 Ironhead Sportster chopper 1987 GMC 3/4 ton 4X4 Diesel 1989 Honda Civic (Heavily modified) --------------------- Section 609 MVAC Certified --------------------- "He who fights with monsters might take care lest he thereby become a monster. And if you gaze for long into an abyss, the abyss gazes also into you." - Friedrich Nietzsche |
#8
|
||||
|
||||
The default position of the climate control flaps (ie, vacuum disconntected or leaking too much for the flaps to work) will blow air out of the side vents and defrost vents only. You definitely have a major vacuum leak somewhere. I wouldn't rule out the connection at the modulator valve, as a tug on that line can pull it out. A Mityvac will help you track down your vacuum leak, and is the only way to be sure that all lines hold vacuum.
__________________
1982 300D, black w/ palomino leather, 203K 2001 E320, champagne, 105K (Mom's) 1999 Dodge Dakota, squeaky & battered, 142K |
#9
|
|||
|
|||
Thanks Guys.
I don't have a Mitty-vac (planning on getting on while down south) so I'll just have to trace each connection by trial and error. At least I'm fairly sure I am looking for a vacuum leak and not something else. Worst case, I'll just have to drive REALLY FAST until I get south of the Mason-Dixon line and hopefully into the |
#10
|
||||
|
||||
Unless you're at least 100 miles from the nearest auto parts store, you'll waste a lot more time hunting down bad connections than going to buy a MityVac NOW. My plastic model was $26 in a "Brake Bleeding Kit" at AutoZone. Every Mercedes should come with a MityVac in the glove box - there's no excuse not to have one.
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#11
|
|||
|
|||
I agree I really need one.
Problem is every parts supplier I've contacted locally here in the frozen north wants $100+ for the privilege of me owning one $30 sounds a whole lot better to me. |
#12
|
||||
|
||||
CarQuest has the metal version for CDN$64.95 here. It's in the lower left corner of page 21.
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#13
|
|||
|
|||
That really makes me
I called CarQuest today and they told me that the MityVac was coming ON SALE next week for $124 Cdn. I asked if they had anything less expensive and was told no. Grrrrrrr Thanks for the lead. |
#14
|
|||
|
|||
I Fixed It !!!!
I found the problem. It wasn't a leak but a blockage in the flex hose from the vacuum pump to the first piece of nylon vac hose. All is now well and Mamma's feet won't freeze on the trip south. Many thanks to all who pointed me in the right direction - this is a GREAT site!!
__________________
1991 M-B 560SEL Arctic White/Grey 99,000 Miles 1987 M-B 300SDL Ivory/Palomino 229,000 Miles (sold but never forgotten) 2006 Volvo XC70 Blue/Beige 1999 Porsche Boxster Arena Red/Savanna Beige 1986 Porsche 928S Goldweiss/Brown |
#15
|
|||
|
|||
Excellent.
Have a good and safe trip down and back. |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to safely jack up a car so all four wheels are off the ground? | zeronero | General Information | 48 | 03-23-2009 10:07 PM |
98 E240 tranny leak and hard shifting | spiral | Tech Help | 3 | 02-07-2003 11:10 PM |
E500 owner in trouble! Help Help! | ERASE | Mercedes-Benz Performance Paddock | 58 | 05-23-2002 12:48 PM |
Stupid EGR..............(hard shifting & MAD smokezz!) | Holson Adi | Diesel Discussion | 9 | 05-18-2002 12:11 AM |
Hard shifting | aantonic | Tech Help | 3 | 10-30-2001 09:58 AM |