|
|
|
|
|
#1
03-16-2007, 01:30 PM
|
|||
|
|||
|
pre cup ( chamber ) removal tool
Howdy Folks :
has anyone posted a foto of a home made pre cup removal tool I remember hearing of one - someone made - but not sure if foto was ever posted: enjoy weeks end cheers ya
__________________
nibiru 82 300TD- diggin it Ich habe Dinge gesehen, die ihr Menchen niemal glauben würdet Gigantische Schiffe, die brannten, draußen vor der Schulter des Orion Und ich habe C-beams gesehen, glizernd im Dunkel, nahe dem Thannhäuser-Tor All diese Momente werden verloren sein....in der Zeit so wie...Tränen im Regen 
|
|
#2
03-16-2007, 02:49 PM
|
|||
|
|||
|
I think one member found that the part on a bicycle that the pedal assembley passes through has the same thread and pitch. The bike was manufactured in the orient I imagine.
|
|
#3
03-16-2007, 02:59 PM
|
|||
|
|||
|
howdy barry:
yes - I found this thread - dated 2003 - a shimano pedal crank removal tool - i think 22MM here is thread - was wondering if anyone ever posted a foto http://www.peachparts.com/shopforum/diesel-discussion/58446-300-5cyl-homemade-prechamber-puller-post354993.html Cheers thanks
__________________
nibiru 82 300TD- diggin it Ich habe Dinge gesehen, die ihr Menchen niemal glauben würdet Gigantische Schiffe, die brannten, draußen vor der Schulter des Orion Und ich habe C-beams gesehen, glizernd im Dunkel, nahe dem Thannhäuser-Tor All diese Momente werden verloren sein....in der Zeit so wie...Tränen im Regen
|
|
#4
03-16-2007, 03:25 PM
|
||||
|
||||
|
On mine, I just used a 1/4 inch bar of flat iron and a metric crescent wrench.
 I have a 603 though.
__________________
All it takes for evil to prevail is for good men to stand by and do nothing. Too many people tip toe through life, never attempting or doing anything great, hoping to make it safely to death... Bob Proctor '95 S320 LWB '87 300SDL '04 E500 wagon 4matic
|
|
#5
03-16-2007, 05:26 PM
|
|||
|
|||
|
I used the tool for the bicycle also, getting it at my local bicycle shop, and I think it only cost like 10 bucks. I then had to take it apart and put the one piece that fits on the pre-chamber onto my slide hammer. I drilled a hole in the end of my slide-hammer, tapped it, and put a screw and washer on it to hold it together. Worked great.
__________________
05 SL600 75K 87 MB 560SL 119K 87 MB 300D 180K 83 MB 240D 110K 64 1/2 Mustang 74 Monte Carlo 32K 75 Fiat 124 Spyder 16 Equinox 15 2500HD Silverado
|
|
#6
03-16-2007, 11:12 PM
|
|||
|
|||
|
howdy mkrazy1;
Right on - wanna post a foto fo that nifty device you engineered Enjoy weeks end Cheers
__________________
nibiru 82 300TD- diggin it Ich habe Dinge gesehen, die ihr Menchen niemal glauben würdet Gigantische Schiffe, die brannten, draußen vor der Schulter des Orion Und ich habe C-beams gesehen, glizernd im Dunkel, nahe dem Thannhäuser-Tor All diese Momente werden verloren sein....in der Zeit so wie...Tränen im Regen
|
 |
| Bookmarks |
|
|
Linear Mode
