|
|
|
#1
|
||||
|
||||
as far as mityvacs go, how does this look?
I have been using the plastic MV for a few years now, and I think it's starting to "suck" in a bad way. everybody here says the metal one is the way to go.
is this an ok one? http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=92474 or should I go for the name brand item for 70.00? John
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread "as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do! My drivers: 1987 190D 2.5Turbo 1987 190D 2.5Turbo 1987 190D 2.5-5SPEED!!! 1987 300TD 1987 300TD 1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere! |
#2
|
|||
|
|||
I say go for the real thing, and get the model that can do pressure as well as vacuum. I got the vacuum
only model and have regretted it ever since. Want to buy my vacuum only Mityvac kit?
__________________
Bob '82 300D Petrol B-G Metallic |
#3
|
||||
|
||||
ya got any pics of the vac/pressure model?
John
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread "as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do! My drivers: 1987 190D 2.5Turbo 1987 190D 2.5Turbo 1987 190D 2.5-5SPEED!!! 1987 300TD 1987 300TD 1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere! |
#4
|
||||
|
||||
I've got the same one. I normally recommend HF stuff, since I think it is usually better than people give it credit for, but not in this case.
The brake bleed container did not seal well, I had to modify it to keep it from leaking. The rubber hose it came with was pre-deteriorated, and had to be replaced almost immediately. Then, after just a few uses, the release valve gummed up, and then the seal on the inside lost its ability to hold vacuum. It was a huge piece of crap. -Sam
__________________
"That f***in' biodiesel is makin' me hungry." 1982 300TD Astral Silver w/ 250k (BIO BNZ) 2001 Aprilia SR50 Corsa Red w/ 5.5k (>100 MPG) |
#5
|
||||
|
||||
Uhh... Mityvac does...
|
#6
|
||||
|
||||
Try this one at Harbor Freight
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=39522 I have been using this one for a few years with no problems.
__________________
1983 300SD 200000miles |
#7
|
||||
|
||||
If your plastic Mityvac is "sucking", or leaking, I would think it would be from a sealing o-ring somewhere, and I bet the metal ones use the same sealing o-rings.
I have heard many folks here with plastic Mityvacs that have worked for a long time. AND, you can't get a $50 dollar vac/pressure pump for $16 bucks....
__________________
Jimmy L. '05 Acura TL 6MT 2001 ML430 My Spare Gone: '95 E300 188K "Batmobile" Texas Unfriendly Black '85 300TD 235K "The Wagon" Texas Friendly White '80 240D 154K "China" Scar engine installed '81 300TD 240K "Smash" '80 240D 230K "The Squash" '81 240D 293K"Scar" Rear ended harder than Elton John |
#8
|
|||
|
|||
I have been using the "plastic" econo-model for 20+ years. All I have ever had to do is clean and lubricate the internal rubber with silicone lubricant.
__________________
Sam 84 300SD 350K+ miles ( Blue Belle ) |
#9
|
||||
|
||||
no, mine is not leaking, it is just difficult to use. the levers feel iffy.
I just figure a metal one will be better. but it still works fine. John
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread "as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do! My drivers: 1987 190D 2.5Turbo 1987 190D 2.5Turbo 1987 190D 2.5-5SPEED!!! 1987 300TD 1987 300TD 1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere! |
#10
|
||||
|
||||
You want the Silverline 4050 kit... metal body, vacuum and pressure. I use this for boost pressure testing as well as vacuum testing:
http://www.thetoolwarehouse.net/shop/MIT-4050.html |
#11
|
||||
|
||||
I have it, and it works great. Paid $14 for it at HF. I've diagnosed several door lock issues with it so far.
__________________
-diesel is not just a fuel, its a way of life- '15 GLK250 Bluetec 118k - mine - (OC-123,800) '17 Metris(VITO!) - 37k - wifes (OC-41k) '09 Sprinter 3500 Winnebago View - 62k (OC - 67k) '13 ML350 Bluetec - 95k - dad's (OC-98k) '01 SL500 - 103k(km) - dad's (OC-110,000km) '16 E400 4matic Sedan - 148k - Brothers (OC-155k) |
#12
|
||||
|
||||
Quote:
|
Bookmarks |
|
|