|
|
|
#1
|
|||
|
|||
W123-W126 interchangeability
Will the rear seat from a 81 126 fit into my 83 123?
any mods needed?
__________________
81 Mercedes 300SD 289k.......SOLD 82 Mercedes 300CD 252k......slow ride 82 mercedes 300 SD...mi Unknown 83 Mercedes 300D ????ksniff..gone too 84 Mercedes 300D 148k........SOLD 85 Mercedes 300TD 386k and holding some one elses project |
#2
|
||||
|
||||
All you have to do is cut the car in half and add a 3 inch piece of metal -
Jack I am fairly certain the 126 bench is longer BUT the 126 bench is 58 inches if you want to run a tape on your 123
__________________
BENZ THERE DONE THAThttp://www.peachparts.com/shopforum/...c/progress.gif 15 VW Passat TDI 00 E420 98 E300 DT 97 E420 Donor Car - NEED PARTS? PM ME! 97 S500 97 E300D 86 Holden Jackaroo Turbo D 86 300SDL (o\|/o) |
#3
|
||||
|
||||
Someone on here did it. It doesnt bolt in and doors are hard to close. He was able to do the front.
__________________
http://superturbodiesel.com/images/sig.04.10.jpg 1995 E420 Schwarz 1995 E300 Weiss #1987 300D Sturmmachine #1991 300D Nearly Perfect #1994 E320 Cabriolet #1995 E320 Touring #1985 300D Sedan OBK #42 |
#4
|
|||
|
|||
Will the covering at least fit in the back over my existing springs
or would it look tacky? I know the front will work, I have done that many times, but I would like to change the color of the seats. I have found a nice 126 with black leather and would like to see it in the 123 instead of the Palimino. What about switches for the power seats? The 126 is power and I would like to keep it that way in the 123.......is that possible, again without looking tacky
__________________
81 Mercedes 300SD 289k.......SOLD 82 Mercedes 300CD 252k......slow ride 82 mercedes 300 SD...mi Unknown 83 Mercedes 300D ????ksniff..gone too 84 Mercedes 300D 148k........SOLD 85 Mercedes 300TD 386k and holding some one elses project |
#5
|
|||
|
|||
It won't work without some effort. I picked one up for my '81 300D by mistake and didn't realize until I was putting it in. It is a bit wide, I was able to get the seat back attached witht the screws, but this cause the back to sit too high to hook at the top. The seat bottom squeezed in, but the latches are different so it won't latch. Also, because it is squeezed in there kinda tight, it causes the seatbelt to bind and they don't retract easily. I only spent about an hour fiddling with it, so with a little more work you might get it to work.
|
#6
|
||||
|
||||
I've researched this a bit myself. I have a line on a fairly decent set of leather pinkamino seats from a W126. Looks like keeping power seats in the front could be challenging. The back seat covers could be modified to fit the original seat frames fairly well, but I'm still hung up on what to do about the folding armrest in the back... They hinge at opposite ends.
__________________
- K.C.Adams '77 300D Euro Delivery OM617 turbo / 4-speed swap 404 Milanbraun Metallic / 134 Dattel MB-Tex Current status: * Undergoing body work My '77 300D progress thread |
Bookmarks |
|
|