Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 10-31-2007, 02:14 PM
JBG JBG is offline
Registered User
 
Join Date: Jun 2007
Posts: 174
Rear D Fill Plug Holy S**t

OK, so I've had the car up on the ramps twice now, trying to knock the fill plug off so I can change the rear differential oil. I didn't think it would be so ridiculously difficult. I've emptied almost an entire can of Liquid Wrench on it trying to loosen it up. It's rusted to hell. I think the last time it was taken off was at least 10 years ago (random guess). I'm using a 1/2 inch driver and 14mm hex bit attached. It is a swivel type so I can get some decent angles on it....still, after pushing, pulling, hammering with all my might, NADA. I've dealt with some tough plugs in my life but nothing like this.

I'm not Arnold Swar_______er, but I'm not slim pickens, either. I probably have as much muscle mass as your average German, though I'm not German. In other words, Mercedes should've/probably expected a dude with my strength to be working on this thing. Of course not on a plug that's been there for years without any love. I just bought the car a year ago and am doing all the maintenance to get it up to snuff. This is the last thing on the list.......krikey.

Any advice beyond "just keep doing what you're doing" is appreciated. I understand if there's nothing to say....hm. Is it possible it's never coming out?!?!?!?!

Thanks guys.

__________________
JBG
1985 TD wagon, 228k
running on grease since 3.07
AUSTIN, TEXAS

Last edited by whunter; 10-31-2007 at 09:04 PM. Reason: spelling
Reply With Quote
  #2  
Old 10-31-2007, 02:20 PM
Diesel Preferred
 
Join Date: Oct 2007
Location: Charleston SC
Posts: 2,788
Get access to an air-powered wrench, and it will come off quite easily. Perhaps a visit to a local mechanic with a plate of brownies is all it will take...
__________________
Respectfully,
/s/
M. Dillon
'87 124.193 (300TD) "White Whale", ~392k miles, 3.5l IP fitted
'95 124.131 (E300) "Sapphire", 380k miles
'73 Balboa 20 "Sanctification"
Charleston SC
Reply With Quote
  #3  
Old 10-31-2007, 02:21 PM
ForcedInduction
Guest
 
Posts: n/a
Cheater bar.

Get a piece of tube over the end of your ratchet and push/pull on it.
Reply With Quote
  #4  
Old 10-31-2007, 02:23 PM
dieseldan44's Avatar
Registered User
 
Join Date: Nov 2006
Location: Boston
Posts: 2,042
JBG,

I did this. It's tough.

It took me an 18" breaker bar extended with about a footlong section of pipe to get enough leverage to break it free. Heating the plug with a torch will also help the situation, but I did not need to go this far. With your rust it sounds like you may need to go there. If you dont have a torch theyre cheap at the local hardware store.

When you put it back, needless to say, put some anti-seize compound in case you ever are in the area again.

Good luck,

dd
__________________
-------------------------------
'85 300D, 'Lance',250k, ... winter beater (100k on franken-Frybrid 3 Valve Kit)
'82 300D, 'Tex', 228k body / 170k engine ... summer car
'83 300TD Cali Wagon 210k, wife's car
Reply With Quote
  #5  
Old 10-31-2007, 02:24 PM
ForcedInduction
Guest
 
Posts: n/a
Take a high-speed run on the highway, what will get it nice and hot too.
Reply With Quote
  #6  
Old 10-31-2007, 02:26 PM
Registered User
 
Join Date: Jan 2006
Posts: 311
A cheater bar got mine out. I found it didn't have a copper washer. Maybe some heat would help, too. Steve
Reply With Quote
  #7  
Old 10-31-2007, 02:27 PM
Hatterasguy's Avatar
Zero
 
Join Date: Nov 2002
Location: Milford, CT
Posts: 19,318
Air impact gun.
__________________
1999 SL500
1969 280SE
2023 Ram 1500
2007 Tiara 3200
Reply With Quote
  #8  
Old 10-31-2007, 02:50 PM
Registered User
 
Join Date: May 2007
Posts: 24
I did this not too long ago, I ended up using the handle off of my floor jack as a cheater bar--about four feet. It still took some major force and a few choice words were thrown in for good measure. I had soaked it for over a week with PB Blaster everyday. I was going to use my impact wrench but I was afraid it might strip the plug and then I would have been in a real mess--prefer to use old fashioned force on things that would be a major PIA if the impact wrench tore them up. Get a bigger pipe and keep trying it will break free--just wait until you see what comes out. Good luck.
Reply With Quote
  #9  
Old 10-31-2007, 03:01 PM
TTCummins's Avatar
Registered User
 
Join Date: Dec 2006
Location: Ypsilanti, Michigan
Posts: 240
CAREFUL WITH THE IMPACT. I think the situation you are running into is similar to mine on an old Muncie trans. I when to change the diff lube in it as well and the steel plug had pretty much welded itself into the aluminum case. I tried everything, which led me to the impact. 30 seconds of impacting and boom, sheared the plug hex right off. Had to drop the trans disassemble it drill it out helicoil it, not fun you get the picture.
__________________
2003 Dodge Ram 2500 Cummins - Georend fully built trans, Banks Big Hoss Bundle, Smarty Tuner, 5" turbo back exhaust. 500 HP and 1100 ft/lbs to the ground.
1979 Mercedes-Benz 300CD - Lost to a four car pile up on 275, Thank You Michigan Drivers.
1986 Mercedes-Benz 300D - Sold, Euro non-turbo car.
Reply With Quote
  #10  
Old 10-31-2007, 03:16 PM
Gene
 
Join Date: Mar 2007
Location: Buffalo NY
Posts: 1,102
Heat the housing surrounding it gently, and wick some wax into the threads. Your children should be able to move it then.
Reply With Quote
  #11  
Old 10-31-2007, 03:45 PM
Moderator
 
Join Date: Jul 2001
Location: Woolwich, Maine
Posts: 3,598
These plugs are often tapered pipe plugs and have no aluminum washer. I always take my 14mm Allen wrench I bought for this purpose in 1976, and a heavy headed hammer, and bang on it. Hard. Clean out the hex socket, and to get a really good grip between the wrench and the socket, wet the end of the Allen wrench, and then dip it in Ajax or Comet. I read that little gem here a while back. It keeps the wrench in the socket better, but you have to clean the socket out good.

Once it moves, you will have to keep knocking on it until it really gets "hand tight" and you can turn it by hand. When I put them back in, I make sure the threads on both parts are clean, then I run it in by hand and tap it shut with a few easy hammer blows. It snugs up and stops turning, which is when you stop tapping with the hammer.

I give the ones with the aluminum washers and the straight threads a similar treatment to remove them, but when you put them back in, I believe there is a torque value specified. If you don't have a torque wrench, red face tight works from experience. Jim
__________________
Own:
1986 Euro 190E 2.3-16 (291,000 miles),
1998 E300D TurboDiesel, 231,000 miles -purchased with 45,000,
1988 300E 5-speed 252,000 miles,
1983 240D 4-speed, purchased w/136,000, now with 222,000 miles.
2009 ML320CDI Bluetec, 89,000 miles

Owned:
1971 220D (250,000 miles plus, sold to father-in-law),
1975 240D (245,000 miles - died of body rot),
1991 350SD (176,560 miles, weakest Benz I have owned),
1999 C230 Sport (45,400 miles),
1982 240D (321,000 miles, put to sleep)
Reply With Quote
  #12  
Old 10-31-2007, 03:49 PM
83 300sd
 
Join Date: Sep 2007
Location: Dirty Jersey
Posts: 16
36" breaker for me, No problem. Pop the fill plug first if you can use a fluid evaccuator and the refill what you took out.
Reply With Quote
  #13  
Old 10-31-2007, 04:05 PM
pawoSD's Avatar
Dieselsüchtiger
 
Join Date: Oct 2004
Location: Grand Rapids, MI
Posts: 15,438
I'm surprised no one posted the easiest way to do it:

1. Put car up on small ramps so you can get under it.

2. Insert the drain plug socket with an 18"+ breaker bar on it in the right position so that:

3. Insert floor jack under handle of breaker bar so that when you begin lifting, it will force the plug counter clockwise.

4. Keep going even when it seems it will lift the car off the ramps, it will "POP!" free.

This has worked on all 3 of our MB's that I have worked on. On mine it raised the car a good 8-10 inches on the suspension before there was enough force to break it loose.

Heating the diff around the plug should help too...expands the metal.

Good luck!
__________________
-diesel is not just a fuel, its a way of life-
'15 GLK250 Bluetec 118k - mine - (OC-123,800)
'17 Metris(VITO!) - 37k - wifes (OC-41k)
'09 Sprinter 3500 Winnebago View - 62k (OC - 67k)
'13 ML350 Bluetec - 95k - dad's (OC-98k)
'01 SL500 - 103k(km) - dad's (OC-110,000km)
'16 E400 4matic Sedan - 148k - Brothers (OC-155k)
Reply With Quote
  #14  
Old 10-31-2007, 04:13 PM
83 300sd
 
Join Date: Sep 2007
Location: Dirty Jersey
Posts: 16
Quote:
Originally Posted by pawoSD View Post
I'm surprised no one posted the easiest way to do it:

1. Put car up on small ramps so you can get under it.

2. Insert the drain plug socket with an 18"+ breaker bar on it in the right position so that:

3. Insert floor jack under handle of breaker bar so that when you begin lifting, it will force the plug counter clockwise.

4. Keep going even when it seems it will lift the car off the ramps, it will "POP!" free.

This has worked on all 3 of our MB's that I have worked on. On mine it raised the car a good 8-10 inches on the suspension before there was enough force to break it loose.

Heating the diff around the plug should help too...expands the metal.

Good luck!
Oh !@#$ Now i remember i had to do that as well. Absolutely right!!!! Be ready to barf when that thing comes out cause the diff oil has a smell like no other EWWWWW. Wear long rubber gloves..
Reply With Quote
  #15  
Old 10-31-2007, 04:29 PM
rrgrassi's Avatar
mmmmmm Diesel...
 
Join Date: Jun 2006
Location: Royse City Tx
Posts: 5,177
Yep. it smells just like the engine oil that get trapped inside some threaded recess in the block. Since it is rotted dino's, makes sense that is smells like roadkill on a hot summer day...

__________________
RRGrassi


70's Southern Pacific #5608 Fairmont A-4 MOW car

13 VW JSW 2.0 TDI 193K, Tuned with DPF and EGR Delete.

91 W124 300D Turbo replaced, Pressure W/G actuator installed. 210K

90 Dodge D250 5.9 Cummins/5 speed. 400K
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 05:54 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page