Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 04-20-2008, 08:04 PM
B_C B_C is offline
Rattle and Roll
 
Join Date: May 2006
Location: Jasper, Georgia
Posts: 9
Question 124 won't shift

My 1991 300D 2.5 Turbo with 722 418 transmission will not shift out of first gear. I've owned the car over a year and except for shifting a little hard when cold the transmissions been OK until one day when it just stopped shifting. I've disconnected the downshift switch beneath the accelerator and made sure the Bowden cable was adjusted with the slack taken up but not pulling. I'm not sure where to go from here. My first for everything. MB, diesel, posting.

Reply With Quote
  #2  
Old 04-20-2008, 09:07 PM
sixto's Avatar
smoke gets in your eyes
 
Join Date: Jun 2000
Location: Eastern TN
Posts: 20,841
Have you checked fluid level? If you can't get to operating temperature in first gear, the fluid level should be about 1cm below the low mark on the dipstick with the engine running and shift lever in P. What's the condition of the fluid (color, contaminants and smell)?

I understand the kickdown actuator can jam. I don't know if it's accessible from outside the transmission.

Sixto
87 300D
Reply With Quote
  #3  
Old 04-21-2008, 09:26 PM
B_C B_C is offline
Rattle and Roll
 
Join Date: May 2006
Location: Jasper, Georgia
Posts: 9
The fluid is red and there is no burned smell. With the temp about 65 and the car at idle in park the fluid is 12mm below the low level mark.
Reply With Quote
  #4  
Old 04-23-2008, 10:02 PM
gsxr's Avatar
Unbanned...?
 
Join Date: Aug 2001
Location: USA
Posts: 8,101
Next thing I would try is disconnecting the kickdown solenoid at the transmission. It's the single wire going into the very back of the tranny, on the passenger side. What happens if you drive the car and let it wind up to 5000rpm in first gear? Will it upshift, or stay at 5000-5200rpm in first gear? The fluid level sounds acceptable.

The kickdown solenoid *might* be stuck, and yes it can be replaced externally... ATF will drip out while its removed though. BT, DT. I had a faulty solenoid, not a faulty valve... mine wouldn't kick down at WOT. That's the opposite problem though.

If the kickdown valve is good, it sounds depressingly like an internal failure, meaning a rebuild could be in your future.

__________________
Dave
Boise, ID

Check out my website photos, documents, and movies!
Reply With Quote
  #5  
Old 04-23-2008, 10:04 PM
Registered User
 
Join Date: Nov 2007
Posts: 73
Quote:
Originally Posted by B_C View Post
My 1991 300D 2.5 Turbo with 722 418 transmission will not shift out of first gear. I've owned the car over a year and except for shifting a little hard when cold the transmissions been OK until one day when it just stopped shifting. I've disconnected the downshift switch beneath the accelerator and made sure the Bowden cable was adjusted with the slack taken up but not pulling. I'm not sure where to go from here. My first for everything. MB, diesel, posting.
Whats the update on this B_C?
Reply With Quote
  #6  
Old 04-23-2008, 10:05 PM
gsxr's Avatar
Unbanned...?
 
Join Date: Aug 2001
Location: USA
Posts: 8,101
Edit - based on this additional information, via email:

Basically it was fine and one day it won't shift. Only first and reverse. Stays in first as far as 4k RPM and will slip into neutral when you let off and coast. Step on accelerator and will kick into first when the revs get to around 3K. Adjusted Bowden per forum, fluid not burned and at proper level, 12mm below low level, for a cold tranny. Disconnected vacuum line to tranny, no difference.

What's described above is more than a stuck kickdown valve. It shouldn't slip into neutral, it shouldn't need to rev to 3k before kicking into first. Bowden is absolutely irrelevant, you could disconnect it if you want. A total shot in the dark is a failed front pump, but if that's not it, you're looking at a tranny rebuild. This didn't happen shortly after a fluid & filter change, did it?

Reply With Quote
  #7  
Old 04-23-2008, 10:13 PM
babymog's Avatar
Loose Cannon - No Balls
 
Join Date: Jan 2006
Location: Northeast Indiana
Posts: 10,765
Maybe a flush toasted the trans? Common way to kill a good transmission.

I'd have control pressure tested, a trans shop should be your next stop.
__________________

Gone to the dark side

- Jeff
Reply With Quote
  #8  
Old 04-24-2008, 08:13 AM
B_C B_C is offline
Rattle and Roll
 
Join Date: May 2006
Location: Jasper, Georgia
Posts: 9
No flush or fluid/filter change in recent or past history. Any recomendations for a shop in Atlanta? Wasn't expecting this at 187K.
Reply With Quote
  #9  
Old 04-24-2008, 10:12 AM
gsxr's Avatar
Unbanned...?
 
Join Date: Aug 2001
Location: USA
Posts: 8,101
I don't know any tranny shops in Atlanta, but Rusty Cullens (of *************** fame) is in Atlanta... you could give him a call, I know he can recommend a place or two. 800-741-5252, or email rusty@***************.

Sometimes weird stuff like this happens, even at relatively low miles. My sister's '87 300D tranny failed at 220k without any warning, one day it was fine, next day it refused to move an inch, regardless of gear selector position or RPM. What was really frustrating was the fact they had just pulled the tranny within the past year and done a full re-seal, d'oh! All that work for basically nothing. We never did find out what part failed inside, and instead swapped in a Peter Schmid rebuild. The new trans has been working fine so far...

Reply With Quote
  #10  
Old 04-24-2008, 02:23 PM
B_C B_C is offline
Rattle and Roll
 
Join Date: May 2006
Location: Jasper, Georgia
Posts: 9
Thanks for the name, I'm slowly making my way up the learning curve. Even though the fluid level is OK judging by where it should be when cold, I'm thinking about adding to it and see what happens. It's not my luck that it would work but what do I have to lose but the cost of a quart of tranny fluid.
Reply With Quote
  #11  
Old 04-24-2008, 02:37 PM
gsxr's Avatar
Unbanned...?
 
Join Date: Aug 2001
Location: USA
Posts: 8,101
True, it wouldn't hurt... even if it just adds some peace of mind. But only add a half-quart! That should move the level up about 10mm on the dipstick. You don't want to overfill, these trannies don't like overfilling. Use a Dexron-II or Dexron-III fluid.
Reply With Quote
  #12  
Old 04-24-2008, 08:26 PM
B_C B_C is offline
Rattle and Roll
 
Join Date: May 2006
Location: Jasper, Georgia
Posts: 9
Well a pint of fluid did no good, surprise, surprise. Got the name of a place to call from Rusty so I'll trailer it down and see if they can give me a diagnosis. If it comes to rebuild I won't be able to do that, but to replace it is within my realm. Who has pulled and installed a transmission and what would be their advice I wonder?
Reply With Quote
  #13  
Old 04-25-2008, 12:47 AM
gsxr's Avatar
Unbanned...?
 
Join Date: Aug 2001
Location: USA
Posts: 8,101
I have not pulled a tranny on a 124, but from what I've heard, you'll need to get the car jacked up as high as possible, to make room underneath. You'll either need a trans jack, or a couple of strong friends to get it in & out of position - it probably weighs about 150 lbs or so. It's not a fun job, but not terribly complicated either.
Reply With Quote
  #14  
Old 04-25-2008, 01:01 AM
sixto's Avatar
smoke gets in your eyes
 
Join Date: Jun 2000
Location: Eastern TN
Posts: 20,841
Oh, be a man Lower it from the engine on a floor jack, roll it gently off the floor jack onto a cardboard sheet or leak catcher pan, slide it out through whatever clearance there is. Installation is the reverse of removal.

Sixto
87 300D
Reply With Quote
  #15  
Old 04-25-2008, 10:12 AM
Registered User
 
Join Date: Nov 2007
Posts: 73
2nd the "Not fun, but not complicated" part...

It was not fun, but certainly "do-able", especially with it on the lift

You'll need to lower the exhaust (not remove) and go in on the upper trans bolts with a loonnnnnng extension. Those were the biggest pain. Other than that, just make sure you have everything disconnected before you try and remove it. A transmission jack is not necessary, but would be helpful. If you are cheap like me and don't want to buy one, a piece of wood on the jack pad to support the tranny will work. This is definitely a two person/multiple beer break job, but not hard.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 11:00 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page