Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #31  
Old 12-17-2009, 06:38 PM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,042
Quote:
Originally Posted by rrgrassi View Post
I had to use a combo of the AZ press and a 10 ton press (located at work), since I did not have access to the proper tool. The proper tool was $90 last time I checked. Next time...I will buy the proper tool. IT took all freaking weekend to do the job. If I had the proper tool in the beginning, the hardest part would have been repacking the bearings.

The AZ tool would have been fine if, and its a BIG if, the AZ tool would have fit flush on the outer lip of the ball joint.

The $90 tool that you need to use with a Hydraulic Press is now a $99 tool; in the 1st pic and the other tool in the 2nd pic is over $300.
The $99 tool comes with a big punch to drive out the Ball Joint.

Attached Thumbnails
Advanced Auto Ball Joint Press Tool-jtc-ball-joint-tool-1.jpg   Advanced Auto Ball Joint Press Tool-ball-joint-tool-zdmak.jpg  
__________________
84 300D, 82 Volvo 244Gl Diesel
Reply With Quote
  #32  
Old 12-17-2009, 06:55 PM
Registered User
 
Join Date: Sep 2004
Posts: 8,971
Quote:
Originally Posted by dannym View Post
I determine by the fact that I myself and numerous other people have used the Autozone press without damaging the joint.
Did you measure the "before" and "after" rotational torque of the joint? If you did not, you probably have no idea whether damage did or did not occur. That would suggest that you are just speculating.

Quote:
Originally Posted by dannym View Post

You however base your comments on speculation since you yourself have never used the Autozone press.
Contrary to your speculation, I have used a generic ball joint press on numerous domestic vehicles for which it is appropriately suited. When I attempted to use one on my W123, it became immediately apparent that it was poorly suited to the task. It doesn't align the joint properly and it is impossible to use the sleeve adapters so that pressure is applied at the flange, as intended.

Quote:
Originally Posted by dannym View Post
The bottom line is if your going to make a comment base it on facts not speculation.
Sometimes, you don't need to poke a sharp stick in your eye to conclude that it might not be a good idea.
Reply With Quote
  #33  
Old 12-17-2009, 07:46 PM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,042
I forgot to add this to my previous Comments.
As far as I know with the exception of Punch to drive out the Ball Joint there is no special tool made for removing the Ball Joint from the Steering Knuckle.
__________________
84 300D, 82 Volvo 244Gl Diesel
Reply With Quote
  #34  
Old 12-17-2009, 08:11 PM
Registered User
 
Join Date: May 2007
Location: Out in the Boonies of Hot, Dry, Dusty, Windy Nevada
Posts: 9,653
Quote:
Originally Posted by Diesel911 View Post
The $90 tool that you need to use with a Hydraulic Press is now a $99 tool; in the 1st pic and the other tool in the 2nd pic is over $300.
The $99 tool comes with a big punch to drive out the Ball Joint.

In the first picture, I see some chinese chicken scratch on the paper. Is that a harbor freight tool?

Charlie
__________________
there were three HP ratings on the OM616...

1) Not much power
2) Even less power
3) Not nearly enough power!! 240D w/auto

Anyone that thinks a 240D is slow drives too fast.

80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff

We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works
Reply With Quote
  #35  
Old 12-17-2009, 08:14 PM
Registered User
 
Join Date: May 2007
Location: Out in the Boonies of Hot, Dry, Dusty, Windy Nevada
Posts: 9,653
Quote:
Originally Posted by DeliveryValve View Post
The perks of Californian vehicles.



.

It never rains in Bakersfield, there is so much oil there, nothing can rust .


Charlie
__________________
there were three HP ratings on the OM616...

1) Not much power
2) Even less power
3) Not nearly enough power!! 240D w/auto

Anyone that thinks a 240D is slow drives too fast.

80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff

We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works
Reply With Quote
  #36  
Old 12-19-2009, 02:06 PM
JEBalles's Avatar
Registered User
 
Join Date: Jun 2008
Location: Carlisle, MA
Posts: 1,225
Alright, I've got the old ball joint out. Braced the long end against the base of a basketball hoop, the steering joint against a spare wheel on the ground, I taped a big socket to the BJ and it came out pretty easily with a few hits with an 8 lb sledge (like I was splitting wood, whoever made that analogy). This was after heating it up and letting it cool three times. Now for the new one, I'm think of using the generic tool and removing the grease boot. Anyone have any good tips?
__________________
1983 240D 3.0T 4-speed manual, now sold

1989 Subaru GL Wagon 5-speed Touring Edition
Reply With Quote
  #37  
Old 12-19-2009, 02:15 PM
funola's Avatar
Registered User
 
Join Date: May 2005
Location: NYC
Posts: 8,245
Quote:
Originally Posted by JEBalles View Post
Alright, I've got the old ball joint out. Braced the long end against the base of a basketball hoop, the steering joint against a spare wheel on the ground, I taped a big socket to the BJ and it came out pretty easily with a few hits with an 8 lb sledge (like I was splitting wood, whoever made that analogy). This was after heating it up and letting it cool three times. Now for the new one, I'm think of using the generic tool and removing the grease boot. Anyone have any good tips?
Good job! I have taken the 2 steering knuckles off from my 240D parts car as spares and will try to get the ball joint off like what you have done. (splitting wood analog was from me).
__________________
85 300D turbo pristine w 157k when purchased 161K now
83 300 D turbo 297K runs great. SOLD!
83 240D 4 spd manual- parted out then junked
Reply With Quote
  #38  
Old 12-19-2009, 03:52 PM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,042
Quote:
Originally Posted by charmalu View Post
In the first picture, I see some chinese chicken scratch on the paper. Is that a harbor freight tool?

Charlie
It is made over there some place. However, that is not my picture. It is a picture either from one of the Members who did a write up on it (I think it is part of the DIY) or from one of the eBay Sellers that Sells them.

Another thought on China or other imported tools is that the Tube Ball Joint Installer was a good idea. I have seen some inovative tools from that area of the world; despite the quality issue.

Besides, eBay there is 2 other internet selles. But, the cost more from them.

Unfortunatly look at the choices:
Buy the $99 tube type ball joint installer and you need to have a Hydraulic press or take it someplace and have the Ball Joint pressed in.

Pay the $300+ (or use our too rental program) for the correct tool

Just pay a shop to install the Ball Joints

Atempt to do the job with the Generic Ball Joint Press. The good news here is that places like Auto Zone rent it for free as long as you return it to them. So if it does not work and no damage is done you have only lost some time.

Added: To the best of my knowlege Harbor Freight does not sell the Tube Type Ball Joint Installer.
__________________
84 300D, 82 Volvo 244Gl Diesel

Last edited by Diesel911; 12-19-2009 at 04:28 PM.
Reply With Quote
  #39  
Old 12-19-2009, 04:20 PM
JEBalles's Avatar
Registered User
 
Join Date: Jun 2008
Location: Carlisle, MA
Posts: 1,225
Quote:
Originally Posted by Diesel911 View Post
It is made over there some place. However, that is not my picture. It is a picture either from one of the Members who did a write up on it (I think it is part of the DIY) or from one of the eBay Sellers that Sells them.

Another thought on China or other imported tools is that the Tube Ball Joint Installer was a good idea. I have seen some inovative tools from that area of the world; despite the quality issue.

Besides, eBay there is 2 other internet selles. But, the cost more from them.

Unfortunatly look at the choices:
Buy the $99 tube type ball joint installer and you need to have a Hydraulic press or take it someplace and have the Ball Joint pressed in.

Pay the $300+ (or use our too rental program) for the correct tool

Just pay a shop to install the Ball Joints

Atempt to do the job with the Generic Ball Joint Press. The good news here is that places like Auto Zone rent it for free as long as you return it to them. So if it does not work and no damage is done you have only lost some time.
I'm going to try it with the generic press like deliveryvalve. I don't see why it wouldn't work. I think I might do a little practice with the old ball joint, the new one won't be here til monday anyway. A question on the wheel hub: do I need to replace that seal? I think I do, but just making sure.
__________________
1983 240D 3.0T 4-speed manual, now sold

1989 Subaru GL Wagon 5-speed Touring Edition
Reply With Quote
  #40  
Old 12-19-2009, 04:33 PM
DeliveryValve's Avatar
Chairman of my Benz
 
Join Date: Jun 2006
Location: Central California
Posts: 4,159
Quote:
Originally Posted by JEBalles View Post
I'm going to try it with the generic press like deliveryvalve. I don't see why it wouldn't work. I think I might do a little practice with the old ball joint, the new one won't be here til monday anyway. .....
Make sure the press is not going to put pressure on the parts towards the middle past the out lip. If it will, then you will then certainly deform the joint and I would suggest finding another solution.


Quote:
Originally Posted by JEBalles View Post
A question on the wheel hub: do I need to replace that seal? I think I do, but just making sure
.....
You do not have to replace the seal on the hub if you are not going to re-pack the bearings and they are not harden and cracked. But if you do re-pack them, then most likely you'll need new ones as they can get tweaked and not be reusable when removed.


.
__________________
1983 123.133 California
- GreaseCar Veg System


Reply With Quote
  #41  
Old 12-19-2009, 04:52 PM
Registered User
 
Join Date: Sep 2004
Posts: 8,971
Quote:
Originally Posted by JEBalles View Post
I'm going to try it with the generic press like deliveryvalve. I don't see why it wouldn't work.
Would you mind measuring the before and after rotational torque of the stud and posting the results?
Reply With Quote
  #42  
Old 12-19-2009, 06:33 PM
JEBalles's Avatar
Registered User
 
Join Date: Jun 2008
Location: Carlisle, MA
Posts: 1,225
Quote:
Originally Posted by tangofox007 View Post
Would you mind measuring the before and after rotational torque of the stud and posting the results?
Aw jeez. Bit of noob hear, so would you mind explaining exactly how I would go about measuring said torque?

Quote:
Originally Posted by DeliveryValve View Post
Make sure the press is not going to put pressure on the parts towards the middle past the out lip. If it will, then you will then certainly deform the joint and I would suggest finding another solution.
It's putting pressure on the upper ridge of the lip, it looks like what you did in that picture. It's not on anything that moves.
__________________
1983 240D 3.0T 4-speed manual, now sold

1989 Subaru GL Wagon 5-speed Touring Edition
Reply With Quote
  #43  
Old 12-19-2009, 06:44 PM
snookwhaler's Avatar
Linesider
 
Join Date: Feb 2009
Location: Treasure Coast, FL
Posts: 1,417
Quote:
Originally Posted by JEBalles View Post
Aw jeez. Bit of noob hear, so would you mind explaining exactly how I would go about measuring said torque?
Use an old fashioned torque wrench with a needle. Same as you would use to check the rotational torque on a pinion before removing the nut.
__________________
AJ

1985 300D (SOLD)

Reply With Quote
  #44  
Old 12-19-2009, 06:49 PM
funola's Avatar
Registered User
 
Join Date: May 2005
Location: NYC
Posts: 8,245
I watched when the shop installed mine. They used emery cloth on the knuckle ball joint seat to clean off any corrosion. They had a home made press similar to the Mercedes tool and was very careful to turn the screw a few turns, then look to make sure that it is not going in crooked, hammer all around on the outside of the knuckle to relief any stress, turn a few more turns, look, hammer , look hammer till it is fully seated. You may or may not have to remove the ball joint boot depending on the tool you're using so that it's not damaged.
__________________
85 300D turbo pristine w 157k when purchased 161K now
83 300 D turbo 297K runs great. SOLD!
83 240D 4 spd manual- parted out then junked
Reply With Quote
  #45  
Old 12-21-2009, 10:08 AM
winmutt's Avatar
85 300D 4spd+tow+h4
 
Join Date: Apr 2006
Location: Atl Gawga
Posts: 9,346
I just used the C clamp with he adapter that had an angle on it. No damage to boots and the first attempt was crooked but I got the rest done without a problem.

__________________
http://superturbodiesel.com/images/sig.04.10.jpg
1995 E420 Schwarz
1995 E300 Weiss
#1987 300D Sturmmachine
#1991 300D Nearly Perfect
#1994 E320 Cabriolet
#1995 E320 Touring
#1985 300D Sedan
OBK #42
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page