Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

View Poll Results: 606 Glow Plug stuck, Opinion Poll
Try drilling out GP myself 1 12.50%
bring it to dealer to have them try drilling out GP 1 12.50%
Try pulling head myself 3 37.50%
bring it to Indy to have them pull head 3 37.50%
Voters: 8. You may not vote on this poll

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-17-2012, 08:07 PM
Registered User
 
Join Date: Jun 2006
Location: Northglenn, CO
Posts: 84
Unhappy 606 GP stuck, options Poll

Hi, I've suffered the unfortunate luck of breaking my #6 glow plug in the head while trying to removed it. I got the other 5 out, but 6 broke right behind the nut. Plug is still fully threaded onto head.
What should I do. I've done a bunch of research on pulling the head and I have the WIS, but to be honest it scares the crap out of me( so many little things I could F-up, like drop something into the abyss).Also, I've never found a complete run down on what I need to replace after pulling the head, ie intake gasket, exhaust gasket, oil filter housing gasket, and what should be changed while in there(valve job,rings,injector hard lines)
Anyway, what should I do. I figure I have 4 options.
Try to drill out the plug myself
https://sites.google.com/site/alanmcreynolds/howtoremovebrokenglowplugs-mercedesom606
Bring it to the dealer to have them try to drill it out($500) and they might still have to pull the head($$$$)
Pull the head myself
or bring it to and indy I've been to a few times and let them pull the head($$$).
On a side note, I did a cold compression check on the other 5 cylinders and got
#1 260
#2 300
#3 280
#4 300
#5 280
Should this influence my decision?
Car is a 99 E300D, w210 chassis, om606.
Thanks

__________________
1980 240D(the first, 4spd)
1983 300D(WVO experiment) gave to my brother
1987 300D(sold with 360k+ miles on original #14 head)
1999 E300D 225k miles and counting
Reply With Quote
  #2  
Old 07-17-2012, 08:17 PM
engatwork's Avatar
Registered User
 
Join Date: May 2000
Location: Soperton, Ga. USA
Posts: 13,646
I've got a customer with the same car that had taken it to an independent a few years ago to get new glow plugs. Seems that one broke off and the customer did not want to pay for having the head removed and gp repaired. The independent laid a spare glow plug on the metal piece below the intake and bailing wired it to the piece. Car is running like that to this day. It is easy to tell when the glow plug relay is working because you can see that one glowing. Granted it cold starts rough but he saved some money.

I have yet to see one of these (98/99) need a head gasket.
__________________
Jim
Reply With Quote
  #3  
Old 07-17-2012, 08:32 PM
Registered User
 
Join Date: Feb 2004
Location: Walnut Creek, CA & 1,150 miles S of Key West
Posts: 4,874
Same situation. #6 is to darn close to the oil filter housing to get a good grip on. I tried 3 times. Cut down 6 point sockets, tried shorter 12 point, etc. Already cut the electrode off with a dremel to get a better angle on it. Its rounded off like a 9mm Luger. Tried extractor sockets of multiple kinds and an 18" breaker bar. Its solid and rounds off before it breaks. Can't drill it without removing the oil filter housing first and then due to it being angled back toward the firewall it would take a truly unique drill and short bit to hit the angle right. No good solutions.

So....i'm, going on vacation next week, and an indy is pulling the head and sending it to a machine shop to drill it out.

He'll bust the other 5 loose, antisieze them, and stick them back it before he buttons it up. These went 199k miles before the 1st one went south.

Number 6 is a flat out bear.

edit: PS: I cant imagine taking a 14y/o car to the dealer for anything major (or minor for that matter); they'll spend more than the car is worth in a hearbeat.
__________________
Terry Allison
N. Calif. & Boca Chica, Panama

09' E320 Bluetec 77k (USA)
09' Hyundai Santa Fe Diesel 48k (S.A.)

Last edited by TMAllison; 07-17-2012 at 09:03 PM.
Reply With Quote
  #4  
Old 07-17-2012, 09:02 PM
Diesel911's Avatar
Registered User
 
Join Date: Sep 2007
Location: Long Beach,CA
Posts: 51,036
Clearly pulling the Head and sending it to a shop the specializes in removing broke stuff like that is the surest way of not causing more damage.

If there is no room to drill it straight the chances of it coming out are poor and the chances of some damage are increased.

I mentioned this once before I think. What is needed is a Polite Drill that matches the inside hole in the Glow Plug Body (what ever size that is) and has an outside diameter that is the same as the lowest threaded spot on the Glow Plugs.
The Pilot end would keep the Drill centered and you only need to drill just past the threads.

After that soaking with Penetrating Oil and tapping the inside of the Glow Plug for a screw as is in the DIY to pull it out.

Unforunately I don't know the sizes needed to see if there is anything that could be adapted (there is inch sized pilot drills) and I don't have the means to make one easily (and if I did I would need to know the sizes).
I also have no idea if the inside hole in a Beru Glow Plug is the same size as a Bosch one.
__________________
84 300D, 82 Volvo 244Gl Diesel
Reply With Quote
  #5  
Old 07-17-2012, 09:03 PM
Registered User
 
Join Date: Feb 2009
Location: Roanoke, VA
Posts: 833
Cost estimate for OM606 head removal for GP replacement...

Done it many times now. HAVE to use hex head screws with washer style heads.

Cost estimate for OM606 head removal for GP replacement...
__________________
1987 300SDL #1, 1987 300SDL #2, 1980 240D, 1982 300SD, 1994 S350, 1990 350SDL, 1991 350SD, 1985 300D, 2005 E320CDI

Gone, but not forgotten: 1981 300SD, 1982 300SD, 1987 300SDL, 1983 300TD, 1980 300CD, 1981 300SD #2, 1987 300D, 1987 300TDT, 1980 300D
Reply With Quote
  #6  
Old 07-17-2012, 09:08 PM
Jeremy5848's Avatar
Registered Biodiesel User
 
Join Date: Mar 2006
Location: Sonoma Wine Country
Posts: 8,402
Dealers

Quote:
Originally Posted by TMAllison View Post


edit: PS: I cant imagine taking a 14y/o car to the dealer for anything major (or minor for that matter); they'll spend more than the car is worth in a hearbeat.
AND . . .

they are unlikely to know much about the "old" (10+ years) cars, even less if it's a diesel. Better luck will be had at an indy who specializes in the older M-Bs.

Jeremy
__________________

"Buster" in the '95

Our all-Diesel family
1996 E300D (W210) . .338,000 miles Wife's car
2005 E320 CDI . . 113,000 miles My car
Santa Rosa population 176,762 (2022)
Total. . . . . . . . . . . . 627,762
"Oh lord won't you buy me a Mercedes Benz."
-- Janis Joplin, October 1, 1970
Reply With Quote
  #7  
Old 07-17-2012, 09:10 PM
Registered User
 
Join Date: Feb 2004
Location: Walnut Creek, CA & 1,150 miles S of Key West
Posts: 4,874
Quote:
Originally Posted by jusme View Post
Cost estimate for OM606 head removal for GP replacement...

Done it many times now. HAVE to use hex head screws with washer style heads.

Cost estimate for OM606 head removal for GP replacement...
Curious what bit and drill combo clears the 3" of space between #6 and the oil filter housing and/or what you use if you first remove the filter? The angle immediately puts you up against the firewall if the drill/bit is more than ~8".

The other 5 are much easier and drilling and extraction methods have been improved in the last 5 years where its usually successful to drill, tap and pull them out of the hole.
__________________
Terry Allison
N. Calif. & Boca Chica, Panama

09' E320 Bluetec 77k (USA)
09' Hyundai Santa Fe Diesel 48k (S.A.)
Reply With Quote
  #8  
Old 07-17-2012, 09:12 PM
Registered User
 
Join Date: Jan 2002
Posts: 18,350
If it were me, I'd think of it as a 5 glow plug car from now on. I'd use a block heater in the dead of winter.
__________________
1977 300d 70k--sold 08
1985 300TD 185k+
1984 307d 126k--sold 8/03
1985 409d 65k--sold 06
1984 300SD 315k--daughter's car
1979 300SD 122k--sold 2/11
1999 Fuso FG Expedition Camper
1993 GMC Sierra 6.5 TD 4x4
1982 Bluebird Wanderlodge CAT 3208--Sold 2/13
Reply With Quote
  #9  
Old 07-17-2012, 09:20 PM
Registered User
 
Join Date: Feb 2009
Location: Roanoke, VA
Posts: 833
It's tight, have used a friends 1/4" right angle drill with the filter housing removed. More often for me, the bolt rips off the element though. Once that happens, little work needs to be done to start the screws into the elements. The one in the picture with just a small amount of element is the hardest kind to get out. And with those, you have to start the screw so deep into the chamber that you risk damaging threads if you're not careful as you extract.

Quote:
Originally Posted by TMAllison View Post
Curious what bit and drill combo clears the 3" of space between #6 and the oil filter housing and/or what you use if you first remove the filter? The angle immediately puts you up against the firewall if the drill/bit is more than ~8".

The other 5 are much easier and drilling and extraction methods have been improved in the last 5 years where its usually successful to drill, tap and pull them out of the hole.
__________________
1987 300SDL #1, 1987 300SDL #2, 1980 240D, 1982 300SD, 1994 S350, 1990 350SDL, 1991 350SD, 1985 300D, 2005 E320CDI

Gone, but not forgotten: 1981 300SD, 1982 300SD, 1987 300SDL, 1983 300TD, 1980 300CD, 1981 300SD #2, 1987 300D, 1987 300TDT, 1980 300D
Reply With Quote
  #10  
Old 07-17-2012, 09:35 PM
Registered User
 
Join Date: Feb 2004
Location: Walnut Creek, CA & 1,150 miles S of Key West
Posts: 4,874
Thanks JUSME. Ive considered the right angle drill and even cutting a drill bit down. Not confident it would do the job with a reasonable chance of success. At elast not in my hands. Hard enough to even get the dremmel back in there to cut the element off.

At a point in my life where i've had enough fun and its time for someone else to deal with it. Indy's have to eat too.

Going to try to trade my '85 back to him for the job. He wants $1800 with the head being redone. My daughter doesnt want it and perfers the 99 which with its 6 air bags and more current design is many times safer when she begins driving in 2 years.
__________________
Terry Allison
N. Calif. & Boca Chica, Panama

09' E320 Bluetec 77k (USA)
09' Hyundai Santa Fe Diesel 48k (S.A.)
Reply With Quote
  #11  
Old 07-17-2012, 09:48 PM
Registered User
 
Join Date: Feb 2009
Location: Roanoke, VA
Posts: 833
AMEN.

Quote:
Originally Posted by TMAllison View Post
Indy's have to eat too.
__________________
1987 300SDL #1, 1987 300SDL #2, 1980 240D, 1982 300SD, 1994 S350, 1990 350SDL, 1991 350SD, 1985 300D, 2005 E320CDI

Gone, but not forgotten: 1981 300SD, 1982 300SD, 1987 300SDL, 1983 300TD, 1980 300CD, 1981 300SD #2, 1987 300D, 1987 300TDT, 1980 300D
Reply With Quote
  #12  
Old 07-17-2012, 10:15 PM
Registered User
 
Join Date: Aug 2009
Location: MN
Posts: 1,253
Quote:
Originally Posted by kerry View Post
If it were me, I'd think of it as a 5 glow plug car from now on. I'd use a block heater in the dead of winter.
X2
__________________
Greg
2012 S350 BlueTEC 4Matic
2007 ML 320 CDI
2007 Leisure Travel Serenity
2006 Sprinter 432k
2005 E320 CDI
1998 SLK230 (teal)
1998 SLK230 (silver)
1996 E300D 99k, 30k on WVO
Previous:
1983 240D, on WVO
1982 300D, on WVO
1983 300CD, on WVO
1986 300SDL 237k, 25k on WVO (Deerslayer)
1991 350SDL 249k, 56k on WVO - Retired to a car spa in Phoenix
1983 380 SEC w/603 diesel, 8k on WVO
1996 E300D 351k, 177k on WVO
Reply With Quote
  #13  
Old 07-17-2012, 11:53 PM
Registered User
 
Join Date: Jun 2006
Location: Northglenn, CO
Posts: 84
So no one has an issue with the compression numbers?

I really want to fix it. I love this car, and if it's possible to fix it right I want to try. I know the car would start fine with 5 good plugs(one was bad last winter) but I want it right.

Jeremy5848-the dealer has the special tools as seen in here. Not sure if they are for the 606 or CDI like the video, but the tech I talked to said they would try the tools first. Then if they don't have access like TMAllison talked about then it's off with it's head.

jusme-the threads are still in the head. So your screw and pry technique won't help, maybe if I get a reverse thread screw.
I've been thinking that since their is so much of the plug still sticking out I might get lucky with some channel locks.
__________________
1980 240D(the first, 4spd)
1983 300D(WVO experiment) gave to my brother
1987 300D(sold with 360k+ miles on original #14 head)
1999 E300D 225k miles and counting
Reply With Quote
  #14  
Old 07-18-2012, 04:13 AM
turbobenz's Avatar
Registered User
 
Join Date: Nov 2007
Location: Cameron Park CA
Posts: 1,874
curious, I have a 94 e300D im putting together. I dont know why, but the head was removed. I bought it as a parts car. the head is on, never got to run! Inspecting why i noticed the motor wouldnt turn over. Reason? Dumb mechanic forgot to install the pins in the timing chain upper rail. So it got eaten by the ip gear jamming the engine LOL and they ditched the whole project (prob though the pistons and valves hit). ANYWAY, first thing I did was remove all six gp's. How do I make sure they never seize? I plan on removing them once every 20k as a preventative measure. Do they need to be reamed? I, and we, need to know how to prevent this issue. Its the only issue this motor really has and its a show stopper.

Also,op, to not hijack your thread I would try removing it via conventional methods. but we all know that aint gonna happen. Remove the head and take it to a good machinist that Knows mercedes heads. I did a 603 head and it really wasn't that difficult. Just time consuming. Spend an hour or two on it here and there (the best way to avoid frustration is taking automotive work in low doses) and it should be a great learning experience.
__________________
1981 300SD 512k OM603



Last edited by turbobenz; 07-18-2012 at 04:31 AM.
Reply With Quote
  #15  
Old 07-18-2012, 08:43 AM
Registered User
 
Join Date: Feb 2009
Location: Roanoke, VA
Posts: 833
Quote:
Originally Posted by Geezer View Post
jusme-the threads are still in the head. So your screw and pry technique won't help, maybe if I get a reverse thread screw.
I've been thinking that since their is so much of the plug still sticking out I might get lucky with some channel locks.
If there is quite a bit still accessible by pliers, get a set of these tongue and groove nutbusters. They are made to either remove it or break the nut in half. Either way it will come out, or give access to the element.

http://www.northerntool.com/shop/tools/product_200308925_200308925?cm_mmc=Google-pla-_-Hand%20Tools-_-Pliers-_-558652&ci_sku=558652&ci_gpa=pla&ci_kw={keyword}

__________________
1987 300SDL #1, 1987 300SDL #2, 1980 240D, 1982 300SD, 1994 S350, 1990 350SDL, 1991 350SD, 1985 300D, 2005 E320CDI

Gone, but not forgotten: 1981 300SD, 1982 300SD, 1987 300SDL, 1983 300TD, 1980 300CD, 1981 300SD #2, 1987 300D, 1987 300TDT, 1980 300D
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 05:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page