|
|
|
#1
|
|||
|
|||
w124 ball joint press
This ball joint press looks very nice - Im thinking of making one myself with 2 1/2 inch thick steel plates.
with 4 bolts pulling this press sits square and will apply a lot of force. Traggelenkpresse Mercedes 190 W201 W124 Presse Traggelenk Abzieher | eBay
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#2
|
|||
|
|||
Go for it and let us know how it worked out! Getting the correct dia sleves is key.
__________________
You can't always get what you want, but if you try sometime you just might find you get what you need. |
#3
|
|||
|
|||
the plates and threaded rods are the easy bits - 20 for a couple of base plates and about 20 or so for some 4140 threaded rod and nuts (Im thinking acme thread)
Im going to see if a machine shop can mill out a few slivers worth of metal from some pieces of pipe to make the sleeves - looks like I only need to mill a seat into one small piece that will push the joint from the bottom. If it goes smoothly Its going to be a nice joint press.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#4
|
||||
|
||||
I believe you would have to notch the lower spacer ring used for removal. The point at which the ball joint area connects to the lower control arm is not flush to the two contact points on the sides used with original equipment special tool.
__________________
http://i284.photobucket.com/albums/l...aman/Fleet.jpg Peach Parts W124.128 User Group. 80 280SL 85 300SD 87 300TD 92 300D 2.5 Turbo 92 300TE 4Matic |
#5
|
|||
|
|||
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#6
|
|||
|
|||
I used it too.
ive already ordered a couple of 4x4x1/2" steel base plates with 4 holes. for pieces of pipe Im going to visit a metal dealer yard and see if i can get a few scraps of pipes.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#7
|
|||
|
|||
I found the right size pipe in my scrap pipe fittings. take a ball joint to the hardware store to see what fits.
__________________
You can't always get what you want, but if you try sometime you just might find you get what you need. |
#8
|
|||
|
|||
That is also in my head.
Reason to use this is that Ive seen a lot of postings of the HF tool bending out - 4 strong thread rods would prevent that. would B7 be a good choice with equally strong nuts?
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#9
|
|||
|
|||
Surely (4) grade 8 machined threaded bolts wouild apply plenty of force?
__________________
You can't always get what you want, but if you try sometime you just might find you get what you need. |
#10
|
|||
|
|||
I did the job and here are the results - my old joints were rusted in place - even the pinch bolt took some caveman methods to let loose - aerokroil and heat also helped.
the joints were the original factory items with a 1994 date. - the press worked flawlessly and the pipe pieces that I used as drifts were a perfect fit. btw these are 5x5 plates I had a freind at work make for me - the plates I ordered never arrived, the threaded rod is from mcmaster carr. rusted to hell press working in action - I also used a 4 lb hammer to shock the thing loose in order to break the rust bond joint pressed out in 10 minutes of cranking - i cleaned up the rusty hole with some sandpaper and it came out looking new - gotta love MB quality. the worn out joint - it had about 2mm up and down movement and was as floppy as a dead fish
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#11
|
|||
|
|||
New ball joint in place - lemforder item bought right here from this forum's shop.
Please always use either genuine MB ball joint or lemforder, the W124 and 201 are not the best design, there is a constant pull on the joint and it can be lethal if it separates. So please do not compromise - btw the Lemforder joint is very low cost in the first place and comes with a zinc plated bolt for corrossion protection. Im thinking of spraying some body cavity wax on the pinch bolt slit to seal it up and prevent and water entrapment.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#12
|
||||
|
||||
You are very brave to do that with the spring in place! Nice job though. I have spoken (via email) with that guy in Germany. Seeing as it worked out I might just go ahead and order one.
__________________
1995 E300 Diesel |
#13
|
|||
|
|||
if you notice my jack stand under the arm its not even raised 1 notch and the spring is compressed quite a lot too.
So unless the metal square structure of the jackstand lets go Im pretty good. This press is definitely lots better than the one screw C shaped one as you can really crank these nuts without fear and hit it HARD with a hammer too. the cost in ordering was about more than a 100 USD, why not just make it, Im sure you can source a place that has some scrap steel plates and also find a place that can drill out holes for you.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#14
|
||||
|
||||
meh. I've got a press...
much easier. pump pump pump. POP! done. mine is a cheapo 150.00 12 ton unit... I think they are 169 now. of course, you need a spring compressor also.
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread "as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do! My drivers: 1987 190D 2.5Turbo 1987 190D 2.5Turbo 1987 190D 2.5-5SPEED!!! 1987 300TD 1987 300TD 1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere! |
#15
|
|||
|
|||
I think I jumbled my post - the 100 dollar sentence was for benedict who was speaking of the german guy selling it on ebay.
For me this press is less than 22 bucks tops including the 3 ft threaded rod and nuts from mcmaster carr and it gives you the chance to replace em in situ. Not everyone has the spring compressor handy.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
Bookmarks |
|
|