|
|
|
#1
|
||||
|
||||
running without oil thermostat
In my 39 Studebaker project we are running into fitment issues with the 617 and the stude body. I have a remote oil filter kit but don't see how it can be used with an oil thermostat. Will running with the cooler in the loop all the time cause problems with the oil being too cool?
The car will most likely not be driven much in the winter.
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC] ..I also have a 427 Cobra replica with an aluminum chassis. |
#2
|
|||
|
|||
Tom here is a Google image of some after market Oil Thermostats.
oil thermostat - Google Search The oil can run too cool in the winter or cooler days, would be like removing the Coolant thermostat. Charlie
__________________
there were three HP ratings on the OM616... 1) Not much power 2) Even less power 3) Not nearly enough power!! 240D w/auto Anyone that thinks a 240D is slow drives too fast. 80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works |
#3
|
||||
|
||||
Cool! Thanks Charlie! Whoda thunk there were multiple choices for aftermarket setups!
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC] ..I also have a 427 Cobra replica with an aluminum chassis. |
#4
|
|||
|
|||
Without an oil thermometer it will be difficult to tell. Oil only starts to lubricate completely from 60 degrees C (140F).
|
#5
|
|||
|
|||
Quite a few thoughs surfaced. I wondered if the oil filter housing could be reduced in size and using an external oil filter. Or if continuous loop was employed use a check valve so that it could not drain back causing an initial lubrication delay. Another thought was remoting the whole filter assembly.
The oil cooler to me was never all that impressive as I felt more heat was probably dissipated through the large oil pan with the airflow along it. I guess an open loop could be tried and as long as the oil pressure gauge sagged somewhat at hot idle the viscosity would not be remaining too high. Or oil temperature too low. With the turbo I would not consider elimination of the oil cooler though. The front end design of the stude may or may not enable the same amount of airflow as the 123 front end. I almost said Hudson again but it was too early in the day to rile you up. Even if the Hudson is of good quality in that body style as well. |
#6
|
||||
|
||||
You could fit an oil - coolant heat exchanger. That would help the oil warm up more quickly too.
-J
__________________
1991 350SDL. 230,000 miles (new motor @ 150,000). Blown head gasket Tesla Model 3. 205,000 miles. Been to 48 states! Past: A fleet of VW TDIs.... including a V10,a Dieselgate Passat, and 2 ECOdiesels. 2014 Cadillac ELR 2013 Fiat 500E. |
#7
|
||||
|
||||
Any reason you can't make up 2 plates and relocate the stock filter housing?
__________________
$60 OM617 Blank Exhaust Flanges $110 OM606 Blank Exhaust Flanges No merc at the moment |
#8
|
||||
|
||||
Quote:
Thanks for all the thoughts guys! Yeah, Barry, watchit with the Hudson remarks! The Hudson pickup is indeed similar but the lines are not so elegant as this Studebaker. the Hudson uses a cut off four door body and the study uses this dedicated coupe looking cab which is most lovely.
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC] ..I also have a 427 Cobra replica with an aluminum chassis. |
#9
|
|||
|
|||
Of course you are right Tom. Still both look the same in the dark. I do like the Hudson still but leading a sheltered life have never seen that studabaker model in person to compare. Although the lines are better. Sounds like the different oil pan may solve some of the dilemma.
|
#10
|
||||
|
||||
Does using Multiviscosity Oil change the above?
__________________
84 300D, 82 Volvo 244Gl Diesel |
#11
|
||||
|
||||
The original Oil Cooler Hoses and Fittings have about 1/2" inside diameter.
See pic
__________________
84 300D, 82 Volvo 244Gl Diesel |
#12
|
|||
|
|||
Quote:
|
#13
|
|||
|
|||
A low rent way is to use a pressure relief between the cooler inlet and outlet to prevent the cooler from being over pressured when the oil is cold.
A much better way is to use the stock thermostat in a remote location. |
#14
|
||||
|
||||
The first time I ever drove a car with an oil temperature gauge I was surprised how long it took to get to operating temperature.
__________________
Jim |
#15
|
||||
|
||||
Maybe this is one of the reasons the Oil Temp is so High:" I will say this average oil temperature is 212°F, the boiling point of water" From Bob the Oil Guys site.
This implies that if the Oil is kept cooler it is possible for Water To build up in the Oil. Motor Oil 101 - Bob is the Oil Guy
__________________
84 300D, 82 Volvo 244Gl Diesel |
Bookmarks |
|
|