Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-04-2013, 01:22 PM
rino's Avatar
Registered User
 
Join Date: Mar 2005
Location: Southern California
Posts: 553
How difficult is to replace the master cylinder on a 1979 240D?

I'm at the point where I need to replace the master cylinder. I was able to locate a Mantelli one for about $50, now I need to establish whether this is something that can be done easily (DIY style, basically on a driveway with no specialized tools) or if it is much more complicated and demanding than that.
I'd much appreciate some input from those of you who have done this job.

__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior.
Reply With Quote
  #2  
Old 09-04-2013, 01:36 PM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 38,610
suck contents out of resorvor, unbolt hard lines (3 I believe) unbolt mc from booster, remove tank from existing mc, press into new mc, reverse process, bleed brakes starting from rr then lr then rf and lf.

Pretty simple.
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #3  
Old 09-04-2013, 05:14 PM
Registered User
 
Join Date: Dec 2005
Location: Carson City, NV
Posts: 3,850
The brake master cylinders I've done have all been really easy.
__________________
Whoever said there's nothing more expensive than a cheap Mercedes never had a cheap Jaguar.

83 300D Turbo with manual conversion, early W126 vented front rotors and H4 headlights 400,xxx miles
08 Suzuki GSX-R600 M4 Slip-on 22,xxx miles
88 Jaguar XJS V12 94,xxx miles. Work in progress.
Reply With Quote
  #4  
Old 09-04-2013, 06:08 PM
Registered User
 
Join Date: May 2007
Location: Out in the Boonies of Hot, Dry, Dusty, Windy Nevada
Posts: 9,652
Use Flair nut wrenches on the brake lines to loosen them.

Two 13mm nuts holds the MC to the Brake Booster.

Be sure to Bench bleed (clamp MC in a Vice by the ears where the bolts go through, not the body) the MC, some times there is a kit that comes with the new MC. has a couple hoses that screw into the MC. curve the hoses up and into the reservoir and be sure they are under the Brake Fluid.

Push in on the end of the MC with a blunt rod to push in the piston several times to purge out the air. when you see no more bubbles, unscrew the hoses and mount onto the Brake Booster.

Bleed the brake system as tom said. R/R, L/R, R/F and L/F caliper.

use a Pressure Bleeder, makes it so easy.


Charlie
__________________
there were three HP ratings on the OM616...

1) Not much power
2) Even less power
3) Not nearly enough power!! 240D w/auto

Anyone that thinks a 240D is slow drives too fast.

80 240D Naturally Exasperated, 4-Spd 388k DD 150mph spedo 3:58 Diff

We are advised to NOT judge ALL Muslims by the actions of a few lunatics, but we are encouraged to judge ALL gun owners by the actions of a few lunatics. Funny how that works
Reply With Quote
  #5  
Old 09-04-2013, 07:50 PM
Admiral-Third World Fleet
 
Join Date: Feb 2002
Location: Central FL
Posts: 3,069
B
Quote:
e sure to Bench bleed (clamp MC in a Vice by the ears where the bolts go through, not the body) the MC, some times there is a kit that comes with the new MC. has a couple hoses that screw into the MC. curve the hoses up and into the reservoir and be sure they are under the Brake Fluid.

Push in on the end of the MC with a blunt rod to push in the piston several times to purge out the air. when you see no more bubbles, unscrew the hoses and mount onto the Brake Booster.
^^THIS

and


Quote:
use a Pressure Bleeder, makes it so easy.
^^ THIS

you might get real lucky and not need to do either, but, you will save a lot of potential frustration if you do both.
__________________
80 300SD (129k mi) 82 240D stick (193k mi)77 240D auto - stick to be (153k mi) 85 380SL (145k mi) 89 BMW 535i 82 Diesel Rabbit Pickup (374k mi) 91 Jetta IDI Diesel (155k mi) 81 VW Rabbit Convertible Diesel 70 Triumph Spitfire Mk III (63kmi)66 Triumph TR4a IRS (90k mi)67 Ford F-100 (??)
Reply With Quote
  #6  
Old 09-04-2013, 08:04 PM
rino's Avatar
Registered User
 
Join Date: Mar 2005
Location: Southern California
Posts: 553
Thumbs up

Great! Thanks a lot...
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior.
Reply With Quote
  #7  
Old 10-14-2013, 01:19 PM
rino's Avatar
Registered User
 
Join Date: Mar 2005
Location: Southern California
Posts: 553
Finally got to go through the replacement procedure..

The Metelli brake master cylinder did not come with a kit and could not locate one anywhere, so I improvised a bit using some 1/4" vinyl clear tubing (which by the way screws in tightly into the master cylinder) - the bench bleed procedure went through perfectly this way. Now, I have to find the time to bleed the brake system at the four calipers. I'll report results later.
Here are a couple of pictures of how I bench bled the master cylinder without a kit:

How difficult is to replace the master cylinder on a 1979 240D?-master_cylinder_bleed-1.jpg

How difficult is to replace the master cylinder on a 1979 240D?-master_cylinder_bleed-2.jpg
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior.
Reply With Quote
  #8  
Old 10-14-2013, 02:31 PM
Registered User
 
Join Date: Jan 2002
Posts: 18,350
I've installed a number of master cylinders after bench bleeding without then having to bleed the brakes on the car.
__________________
1977 300d 70k--sold 08
1985 300TD 185k+
1984 307d 126k--sold 8/03
1985 409d 65k--sold 06
1984 300SD 315k--daughter's car
1979 300SD 122k--sold 2/11
1999 Fuso FG Expedition Camper
1993 GMC Sierra 6.5 TD 4x4
1982 Bluebird Wanderlodge CAT 3208--Sold 2/13
Reply With Quote
  #9  
Old 10-14-2013, 09:02 PM
vstech's Avatar
DD MOD, HVAC,MCP,Mac,GMAC
 
Join Date: Mar 2006
Location: Mount Holly, NC
Posts: 26,835
Quote:
Originally Posted by kerry View Post
I've installed a number of master cylinders after bench bleeding without then having to bleed the brakes on the car.
yup.
the trick is to let the fluid trickle into the lines before you tighten them up to the MC.
if you allow the air to bubble out of the lines before you tighten them to the MC, you will not need to bleed the entire brake system.
HOWEVER... if the MC is bad, odds are good the fluid is bad in the car anyway, so do yourself a favor and FLUSH the entire brake system with new fluid, and prevent a seized caliper!!!
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread
"as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do!

My drivers:
1987 190D 2.5Turbo
1987 190D 2.5Turbo
1987 190D 2.5-5SPEED!!!

1987 300TD
1987 300TD
1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere!
Reply With Quote
  #10  
Old 10-15-2013, 03:42 PM
Registered User
 
Join Date: Aug 2010
Location: Sacramento, CA
Posts: 3,115
Ditto on always "bench bleed" the MC before connecting the tubes. Otherwise, you will never get all the air out. You don't have to clamp in a vise, I find it easier to pump it on the car using the pedal. True also that you don't need to bleed the whole system if just changing the MC. However, you need to replace the brake fluid every 2 years regardless to avoid severe corrosion. Actually, I don't since I use DOT 5 (silicone fluid) in all my older cars.

I changed the MC in both my 300D's in the last few years, and probably won't ever need to again w/ DOT 5. The MC cost $45 at Autozone and had to re-use my reservoirs. Many times, a failed MC will leak brake fluid into the vacuum booster. If so, remove it and try to get it out. I stuffed rags in to absorb it, then de-rusted and repainted since normal brake fluid (glycol) lifts the paint. Note also that where the MC bolts to the booster is a vacuum seal in my 84 & 85. If true, insure the O-ring is thick enough and the surfaces are clean. In most older cars, the booster had an inner bellows so there was no seal at the MC.
Reply With Quote
  #11  
Old 10-16-2013, 07:12 AM
rino's Avatar
Registered User
 
Join Date: Mar 2005
Location: Southern California
Posts: 553
After installing the new Metelli brake master cylinder and bleeding the system not once but twice, I still have NO decent braking!

To recap, I first bench bled the MC before installing it. Then, after bleeding the system, I drove the car to try the braking and it was very weak. So, thinking there might be still air in the system, I bled it a second time, this time making sure it was done very thoroughly. But I still have no decent braking power.

There is definitely an improvement when comparing to the old MC. With the old one, the car would not hold still (with the brake pedal pressed down) on even a slight slope, I'd have to press down the brake pedal continuously. With the new one, pressing the brake pedal a couple of times and then holding it there keeps the car permanently still on the same slight slope. But as I said, braking is not sufficiently strong to drive the car around safely.

Bill, I'm not sure whether the faulty MC had leaked fluid into the vacuum booster, but I'm inclined to doubt that since the fluid level in the reservoirs did not go down when the older MC was in the car.
However, after installing the new one, the engine no longer shuts off when the ignition if turned off and the key removed. So, this seems consistent with a malfunction in the vacuum system. The new O-ring at the seal was identical in size to the older one. But perhaps I didn't clean the surfaces sufficiently well or something.

Should I take off the MC once again (what a PITA, it was difficult to reconnect a couple of the hard lines) and take a look at the seal? Any thoughts on this?
__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior.
Reply With Quote
  #12  
Old 10-16-2013, 07:43 AM
vstech's Avatar
DD MOD, HVAC,MCP,Mac,GMAC
 
Join Date: Mar 2006
Location: Mount Holly, NC
Posts: 26,835
first, I'd verify the brown line from the IP to the vacuum switch is intact on both ends, make sure you did not bump off a vacuum line.
if the pedal is not hard you don't have to worry about the vacuum seal on the booster.
as for braking problems, if the new MC is not holding the car still... you could have stuck calipers... pull off each tire, and get a screwdriver in there, and verify the pads move back and fourth.
what method are you using to bleed the brakes?
__________________
John HAUL AWAY, OR CRUSHED CARS!!! HELP ME keep the cars out of the crusher! A/C Thread
"as I ride with my a/c on... I have fond memories of sweaty oily saturdays and spewing R12 into the air. THANKS for all you do!

My drivers:
1987 190D 2.5Turbo
1987 190D 2.5Turbo
1987 190D 2.5-5SPEED!!!

1987 300TD
1987 300TD
1994GMC 2500 6.5Turbo truck... I had to put the ladder somewhere!
Reply With Quote
  #13  
Old 10-16-2013, 10:31 AM
Registered User
 
Join Date: Jan 2002
Posts: 18,350
This might be your problem:

http://www.peachparts.com/shopforum/diesel-discussion/189944-worn-front-brake-pads=high-pedal-effort.html
__________________
1977 300d 70k--sold 08
1985 300TD 185k+
1984 307d 126k--sold 8/03
1985 409d 65k--sold 06
1984 300SD 315k--daughter's car
1979 300SD 122k--sold 2/11
1999 Fuso FG Expedition Camper
1993 GMC Sierra 6.5 TD 4x4
1982 Bluebird Wanderlodge CAT 3208--Sold 2/13
Reply With Quote
  #14  
Old 10-16-2013, 04:15 PM
Registered User
 
Join Date: Jul 2008
Posts: 3,740
I think anyone who is working on or planing to work on their braking system should build or invest in a pressure bleeder..

DIY pressure bleeder

Power Fluid Bleeder - Motive Products MOT0100 | FCP Euro
__________________
Reply With Quote
  #15  
Old 10-17-2013, 12:08 PM
rino's Avatar
Registered User
 
Join Date: Mar 2005
Location: Southern California
Posts: 553
Quote:
Originally Posted by vstech View Post
first, I'd verify the brown line from the IP to the vacuum switch is intact on both ends, make sure you did not bump off a vacuum line.
if the pedal is not hard you don't have to worry about the vacuum seal on the booster.
as for braking problems, if the new MC is not holding the car still... you could have stuck calipers... pull off each tire, and get a screwdriver in there, and verify the pads move back and fourth.
what method are you using to bleed the brakes?
I'll check that brown line again tonight, but I remember checking all of the vacuum lines when the engine stopped shutting off via the ignition key (I had experienced a similar problem a few years ago and it was due, precisely, to a vacuum line coming off).
The brake pedal is not hard at all, it feels normal as it usually does with brakes that work well. I just have to press it two or three times to achieve some noticeable braking and then the braking is still weak.
The new MC DOES hold the car still on a slope as I indicated in my previous post.
To bleed the system, I used the power bleeder I built recently (works very well), you can see it here: 240D Brakes: How do I bleed the Master Cylinder?

__________________
1979 240D, W123, 105K miles, stick, white w/ tan interior.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 08:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page