|
|
|
#1
|
||||
|
||||
Mercedes axle shaft diameter?
What would be the diameter of the rear axle from a W123 or such vehicle? The shaft part that pokes into the diff, that is. Does someone have on they could measure for me?
__________________
"Senior Luna, your sense of humor is still loco... but we love it, anyway." -rickymay ____ "Your sense of humor is still loco... " -MBeige ____ "Señor Luna, your sense of humor is quite järjetön" -Delibes 1982 300SD -- 211k, Texas car, tranny issues ____ 1979 240D 4-speed 234k -- turbo and tuned IP, third world taxi hot rod 2 Samuel 12:13: "David said to Nathan, “I have sinned against the Lord.” And Nathan said to David, “The Lord also has put away your sin; you shall not die." |
#2
|
||||
|
||||
It wouldn't be 3 cm, would it?
__________________
"Senior Luna, your sense of humor is still loco... but we love it, anyway." -rickymay ____ "Your sense of humor is still loco... " -MBeige ____ "Señor Luna, your sense of humor is quite järjetön" -Delibes 1982 300SD -- 211k, Texas car, tranny issues ____ 1979 240D 4-speed 234k -- turbo and tuned IP, third world taxi hot rod 2 Samuel 12:13: "David said to Nathan, “I have sinned against the Lord.” And Nathan said to David, “The Lord also has put away your sin; you shall not die." |
#3
|
||||
|
||||
I think you will need to be more specific as there is the diameter that the C clip goes into and then there is the splined section and then there is a section that the Differential Seal rides on.
__________________
84 300D, 82 Volvo 244Gl Diesel |
#4
|
||||
|
||||
I can measure any part of a W123 axle shaft for you - I have one in bits...
...I'll be back
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits! |
#5
|
||||
|
||||
99% sure it's the splined bit, but measurements of multiple points would be good as well .
Thank you, Stretch!!
__________________
"Senior Luna, your sense of humor is still loco... but we love it, anyway." -rickymay ____ "Your sense of humor is still loco... " -MBeige ____ "Señor Luna, your sense of humor is quite järjetön" -Delibes 1982 300SD -- 211k, Texas car, tranny issues ____ 1979 240D 4-speed 234k -- turbo and tuned IP, third world taxi hot rod 2 Samuel 12:13: "David said to Nathan, “I have sinned against the Lord.” And Nathan said to David, “The Lord also has put away your sin; you shall not die." |
#6
|
||||
|
||||
Both ends are the same (on my homokinetic can type axles) 29.4mm +/- 0.1mm
So wheel hub end splines and differential splines are the same outer diameter - not sure about the splines (probably the same i.e. either end will slide on in there but won't fit 'cos of different lengths of course) Solid rod between the cans is 27mm in diameter
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits! |
#7
|
||||
|
||||
__________________
1983 123.133 California - GreaseCar Veg System |
Bookmarks |
|
|