|
|
|
#1
|
|||
|
|||
quick change of brakedisk
I've bought another project car, because of the tax law here the diesel is to expensive.
So I wanted to change the front brake disks and pad, I have done it a few times before, and its straight forward....so i think When I removed the brake calliper and the bracket, you have to remove the inbus bolt and the disk should almost fall off, or an slight knock with an hammer. Well after hammering and hammering, shopowner tried (I'm using the lift there) He can hit harder the me...but a piece of the disk broke off. So I had to grind the disk off, the other side aswell!! Ofcourse to add more to my "misery" an broken wheel bolt, the end was so stuck the shopowner had to weld an nut on it. So, my ranting for today
__________________
1986 W201 190D 2.5 ~ From bare bone to almost full option. 1985 W201 190E 2.0 ~ Project car |
#2
|
||||
|
||||
Whenever customer cars have stuck rotors, I use an air chisel alternating around and it pops them right off.
|
#3
|
|||
|
|||
An air chisel on the back side ?
__________________
1980 240d , chain elongation, cam marks reference: http://www.peachparts.com/shopforum/diesel-discussion/10414-help-i-need-check-stretch.html http://www.peachparts.com/shopforum/diesel-discussion/305365-9-degrees-chain-stretch.html evap fin cleaning: http://www.peachparts.com/shopforum/diesel-discussion/156207-photo-step-step-post-showing-w123-evaporator-removal-1983-240d-1982-300td.html?highlight=evaporator A/C thread http://www.peachparts.com/shopforum/diesel-discussion/297462-c-recommendations-mb-vehicles.html |
#4
|
||||
|
||||
Yep, and on the hub. I'd start with a few love taps from a deadblow. If no joy, I'd get the air chisel and hit it at 3 & 9 from the front on the hub and then from the back rotating it as needed to clear the backing plate. Usually a few back and forths and it popped right off.
On one occasion a coworker was going to TOWN taking his anger out on this one seized rotor. He couldn't get it off after 10 minutes. I went over with the chisel and had it off in 30 seconds. The rapid fire blows work better than strong blows from a sledge (like an impact gun works better than just heaving on a wrench). |
#5
|
||||
|
||||
You can remove the brake caliper first, then use the 2 holes the caliper was fixed on to the stub shaft . A bolt and 2 nuts in the 2 holes and use them to push the disc off the hub. And after you remove them, use a little copper slip on both faces ie disc to hub ,And wheel to disc. .Also wheel bolts .For easy removal next time .
|
#6
|
|||
|
|||
That's a great tip. On my Subaru, the rotors come from the factory with two 8mm holes tapped into the face. When the rotors get stuck, you just thread in a couple of bolts and force them off the hub. Makes it easy.
|
#7
|
||||
|
||||
When the new Rotor is applied does annone use a Neversieze type compound the Hub area so that it does not stick again?
When I have had stuck Rotors or Brake Drums I usually apply heat with a Propane torch. However, in S CA the rust issues are not the same as in other places.
__________________
84 300D, 82 Volvo 244Gl Diesel |
#8
|
|||
|
|||
a touch of some high temperature lube like a silicone spray with teflon on the hub face can keep out water, prevent corrossion and make removing the rotor easier the next time.
__________________
2012 BMW X5 (Beef + Granite suspension model) 1995 E300D - The original humming machine (consumed by Flood 2017) 2000 E320 - The evolution (consumed by flood 2017) |
#9
|
|||
|
|||
I use a product called "Squeak Relief" by Lubegard. It's a compound of wax and aluminum powder in a spray form. You'll find it with the brake cleaner at your favorite parts store. There's a similar product from Wurth, can't recall the name. I was surprised that you could spray this all over the rotor to prevent rust on the hat and edges. Anything that hits the friction surface seems to burn off the first time you press the brakes, with no drama.
Squeak Relief Brake Finishing Treatment |
#10
|
|||
|
|||
I cleaned up the rotor (behind the disk) good. There was not much rust.
I did add a very little copper paste around de wheel bearing hub, there is sticks I think. I am a DIY so never had this before, and am not super handy about mechanical stuff, prefer electrical hehe. I put new ATE break disks on it, I don't think I have change soon again
__________________
1986 W201 190D 2.5 ~ From bare bone to almost full option. 1985 W201 190E 2.0 ~ Project car |
#11
|
|||
|
|||
Your old discs were really scored....
I assume you put new pads on with the new discs ? Perhaps new calipers ? I would NOT recommend spraying anything on the part of the discs which are touched by the brake pads..... just really really clean them with alcohol..... nothing petroleum based... no gasoline, no diesel, etc...it can get into the pores of the metal... then comes out when heated and makes a film on the surface of your brake pads.... bad physics for braking..
__________________
1980 240d , chain elongation, cam marks reference: http://www.peachparts.com/shopforum/showthread.php?threadid=10414 http://www.peachparts.com/shopforum/diesel-discussion/305365-9-degrees-chain-stretch.html evap fin cleaning: http://www.peachparts.com/shopforum/diesel-discussion/156207-photo-step-step-post-showing-w123-evaporator-removal-1983-240d-1982-300td.html?highlight=evaporator A/C thread http://www.peachparts.com/shopforum/diesel-discussion/297462-c-recommendations-mb-vehicles.html |
#12
|
|||
|
|||
Yes, I put new pads in of course, I used sandpaper to clean the bracket where the pads glide in. Then I used small amounts of pasta on the edge of the pads.
I didn't renew the callipers (budget) but I did notice one is sticking a bit. Ill refurbish them myself if needed. I bought the car like this, the old disks where only 7.5mm thick (0.295 inch) New is 11mm Sadly the lack of maintenance is everywhere on the car.
__________________
1986 W201 190D 2.5 ~ From bare bone to almost full option. 1985 W201 190E 2.0 ~ Project car |
#13
|
|||
|
|||
It is not suggested that people renew their own calipers... per the FSM...
buy quality new and matching makes both sides instead.
__________________
1980 240d , chain elongation, cam marks reference: http://www.peachparts.com/shopforum/showthread.php?threadid=10414 http://www.peachparts.com/shopforum/diesel-discussion/305365-9-degrees-chain-stretch.html evap fin cleaning: http://www.peachparts.com/shopforum/diesel-discussion/156207-photo-step-step-post-showing-w123-evaporator-removal-1983-240d-1982-300td.html?highlight=evaporator A/C thread http://www.peachparts.com/shopforum/diesel-discussion/297462-c-recommendations-mb-vehicles.html |
#14
|
|||
|
|||
"I would NOT recommend spraying anything on the part of the discs which are touched by the brake pads.....just really really clean them with alcohol"
You'd think not, but I've used this stuff on both my Porsche and my Mercedes and it works as advertised...less corrosion, no impediment to braking efficiency. |
#15
|
|||
|
|||
Quote:
__________________
1980 240d , chain elongation, cam marks reference: http://www.peachparts.com/shopforum/showthread.php?threadid=10414 http://www.peachparts.com/shopforum/diesel-discussion/305365-9-degrees-chain-stretch.html evap fin cleaning: http://www.peachparts.com/shopforum/diesel-discussion/156207-photo-step-step-post-showing-w123-evaporator-removal-1983-240d-1982-300td.html?highlight=evaporator A/C thread http://www.peachparts.com/shopforum/diesel-discussion/297462-c-recommendations-mb-vehicles.html |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|