Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 05-25-2002, 09:54 PM
Registered User
 
Join Date: Apr 2002
Location: Portland Oregon, USA
Posts: 65
Exclamation HELP! Ingnition Switch wont budge from OFF position!!

ACK!

So i drive my 240d home and shut her off. I forgot to close the sunroof, and wanted to turn the switch back so i can close it (a natural desire, no?).. *!*. the Key will not budge past the Off posistion now! it appears as if it is really stuck in the off position. I can remove and re-insert the ignition key, like normal, but turning it with any effort will not allow it to budge. (its as if i inserted the wrong key!) I thought maybe if i rocked the steering wheel back and forth, it might "unlock" the switch, but no dice as of yet (tho, i do see the switch physically move slightly when i do this). Here is what i have done so far..; I have removed the under-dash panel, so i can take a view under the dash and see the keyswitch assembly. what caught my eye, are two vacuum-looking hoses attached towards the rear of the switch assembly, and it appeared that one or possibly both hoses have an oily film on them (as well as a few drops of dark oil that seems to be run-off from these hoses. these drops of oil seemed to have hit a couple of neighboring wires to the ignition switch as well, btw). I wonder what could be the problem?? Is my Vacuum diaphram shot? Cuz my door locks work great, as does everything else vacuum-related..?? My one concern for the moment, is to get my Sunroof closed somehow! (i think it will start raining later tonite!).. is there a way to manually (even if temporarily), "engage" the ignition switch so i can close the sunroof? Any info/advice to this dilemma, i'd be in your debt! Thanks so much,

Miles

__________________
milesb@mac.com
Reply With Quote
  #2  
Old 05-25-2002, 10:07 PM
Holson Adi's Avatar
Registered User
 
Join Date: Jul 2001
Location: Boston, MA
Posts: 2,561
I'd just close the sunroof using the emergency nut located in the trunk.

it's behind the driver's side trunk plastic liner. Carefully remove the plastic liner and find the sunroof motor.
There should be a plastic nut that you could manually turn to close and open the sunroof.

I don't know what sort of tool you need to manually close it. Maybe you could use an adjustable wrench...

good luck!

replace the ignition switch's tumbler. I have some 'lock' work to be done this week too.
__________________
2008 BMW 335i Coupe
Reply With Quote
  #3  
Old 05-25-2002, 10:45 PM
Registered User
 
Join Date: Sep 2001
Location: central Texas
Posts: 17,281
That is a great feature.... Now, if they had just provided a manual backup system for the 300 electric windows......
Reply With Quote
  #4  
Old 05-25-2002, 10:50 PM
Registered User
 
Join Date: Apr 2002
Location: Portland Oregon, USA
Posts: 65
(!) UPDATE: Thanks for the emergency sunroof info! it worked! got the sunroof all closed up! (and just in time!).. =) now.. back to the ignition switch! ..... grr!!!


-Miles
__________________
milesb@mac.com
Reply With Quote
  #5  
Old 05-26-2002, 05:43 AM
turbodiesel
Guest
 
Posts: n/a
This is really bad news if you cant get the key to turn anymore. I'm sure you have been having this key sticky problem for a while and have just been jiggiling the key to get it to turn.

I have never done this before, but I have heard the only way to get the tumbler assembly out (which is what is bad in your case, NOT the ignition switch) is to drill it out.

Search the posts, there will probably be something on it.
Reply With Quote
  #6  
Old 05-26-2002, 06:11 AM
Banned
 
Join Date: Nov 2001
Location: Cape Cod Massachusetts
Posts: 1,427
Lightbulb Well this might be something the little woman can help you with!

First order of business is to order a new key/tumbler from the dealer so that as soon as you get the key to turn you can remove the old tumbler and pop in your new one!

How to get the key to turn is the next order of business keep trying and jiggling and moving the key eventually the tumbler pins might line up!

Or attach a handle to the key so that you can apply levered pressure in the clockwise direction that the key normally will turn, use a Popsicle stick or small screwdriver. Next get an electrical appliance that vibrates! Yeah any good vibrating appliance will work electric razor, tooth brush, a carbide tipped engraver is good, or well maybe the wife or girlfriend can think of something!?!? and a jigsaw has been known to work!

190E Ignition lock broken - Help needed

Apply slight pressure to the lever and at the same time apply vibrations to the key head, eventually the vibrating tumbler pins will all be in alignment and the key/tumbler will turn. That’s when you remove the old and pop in the new.
Reply With Quote
  #7  
Old 05-26-2002, 06:30 PM
190D22's Avatar
Driver's Side lights
 
Join Date: Apr 2002
Location: Columbus, Ohio
Posts: 876
Well my tumbler died on me too. Fortunately it worked halfway. I had to put the key in and turn it as far as I could then pull the key out a little and then turn it as normal. My valet key worked it perfectly, I've concluded it's because it has the sharpest teeth due to the minimal use compared to the other keys. My new tumber came with a new key which works the old, broken one. I will take pics of what I mean by pulling the key out slightly.
Here is the key where it in all the way and won't turn. By the way, this is my most worn key that I do not use anymore.
Attached Thumbnails
HELP! Ingnition Switch wont budge from OFF position!!-stuck.jpg  
__________________
1984 190D 2.2 Auto 220k
2001 Jeep Cherokee Sport 70K
2004 Lexus RX-330 ??K
2005 Chrylser Crossfire LTD 6K

Play guitar? Go to www.cyberfret.com for free online lessons!
Reply With Quote
  #8  
Old 05-26-2002, 06:31 PM
190D22's Avatar
Driver's Side lights
 
Join Date: Apr 2002
Location: Columbus, Ohio
Posts: 876
Here is the key pulled out to where it will allow me to turn the tumbler.
Attached Thumbnails
HELP! Ingnition Switch wont budge from OFF position!!-out.jpg  
__________________
1984 190D 2.2 Auto 220k
2001 Jeep Cherokee Sport 70K
2004 Lexus RX-330 ??K
2005 Chrylser Crossfire LTD 6K

Play guitar? Go to www.cyberfret.com for free online lessons!
Reply With Quote
  #9  
Old 05-26-2002, 06:31 PM
190D22's Avatar
Driver's Side lights
 
Join Date: Apr 2002
Location: Columbus, Ohio
Posts: 876
And then the tumbler turned.
Attached Thumbnails
HELP! Ingnition Switch wont budge from OFF position!!-turned.jpg  
__________________
1984 190D 2.2 Auto 220k
2001 Jeep Cherokee Sport 70K
2004 Lexus RX-330 ??K
2005 Chrylser Crossfire LTD 6K

Play guitar? Go to www.cyberfret.com for free online lessons!
Reply With Quote
  #10  
Old 05-26-2002, 08:46 PM
MVK MVK is offline
Registered User
 
Join Date: May 2002
Location: Queens, NY
Posts: 447
I had similar problem but its ok now

I had a similar problem in my 300D turbo about 2 yrs back, I disconnected the battery, sprayed some WD40, inserted the key in and used my homedics body massager and hold it against the key and let the vibations run in thru the key and use the free hand to wiggle the key after few attemps it did turn, I also had another key, that worked little better soI started using that key. Also sprayed a lot of graphite lock spray and It has been working since then. I still spray the graphite spray once every 6-8 months just to be sure. and touch wood no probs.
I dont know if this will do the job for you but its worth the try.
uSE A NEWER KEY IF YOU HAVE IT IN SPARE.

Good luck

MVK
__________________
One penny saved is three penny earned.

1985 300D Turbo 179,000miles
Reply With Quote
  #11  
Old 05-26-2002, 09:24 PM
190D22's Avatar
Driver's Side lights
 
Join Date: Apr 2002
Location: Columbus, Ohio
Posts: 876
I tried WD40 as well. It did not help... well at least not that I know of. I did use WD40 in my door locks, man do they turn nice and smooth now!!! Use a spare key, and if that works schedule a service w/ mercedes to get it replaced. They match it to your VIN so the keys all work. It's gonna run you 300 bucks or so. Or you can get the part from them and do it yourself. It's really not too hard.
__________________
1984 190D 2.2 Auto 220k
2001 Jeep Cherokee Sport 70K
2004 Lexus RX-330 ??K
2005 Chrylser Crossfire LTD 6K

Play guitar? Go to www.cyberfret.com for free online lessons!
Reply With Quote
  #12  
Old 05-27-2002, 12:52 AM
billrok's Avatar
Registered User
 
Join Date: Dec 2001
Location: Chicago area
Posts: 242
Wink

WD 40 will work-Short term. Long term, any oils will evaporate the carrier and leave thick, dust catching oil in the lock and on the pins and tumbler causing grief and angst. Most of our cars could use a quick lock tune up: Take off outer handle. It takes all of 45 second to a minute on 123 or 126 Chassis cars. Clean lock assembly thoroughly with electrical contact cleaner. Later 126's have a electrical switch on them also. After cleaning, lube the lock and mechanism with Powered Graphite. Work the key in and out and get that graphite down in all the pins and springs. Graphite is available from any hardware store or Pep Boys. Your locks will work like the day they came off the line in Germany!!
__________________
Orland Park, IL
1985 300SD 215,000 miles
Reply With Quote
  #13  
Old 05-27-2002, 10:21 PM
peterkris
Guest
 
Posts: n/a
My ignition lock is starting to act up, too. My solution has been to leave the key in the lock all the time. My car is an old rusted wagon ('82 TDT), so I figure no one will want to steal it!
Reply With Quote
  #14  
Old 05-28-2002, 03:58 AM
Registered User
 
Join Date: Dec 2001
Location: San Jose, CA
Posts: 854
I don't recommend WD40 for very many uses, other than water displacement. It's light lubricity doesn't last very long, and is not intended to be a lubricant. On locks, never use WD40! It does attract nasty stuff, and you will end up worse off!
Use a lock lubricant only, and you will have excellent service. Shouldn't even wear out!

FWIW dept.
WD40 was the end result of a scientist/chemist (British, I think) who was developing a water dispersal chemical. This was his 40th formula and the one that worked! Thus the name WD40.
When we had points for ignitions, and crummy distributor caps, it was common to get moisture inside the cap and the distributor would misfire the cylinders. The quick settlement was to pop the cap and spray WD40 to get the water out. I always just wiped the water out with a rag and let air dry if I could.
I think that this spray was used by fleets and army verhicles, where you couldn't wait for things to dry!

__________________
Ed
1981 300CD (Benzina)
1968 250 S (Gina) 266,000 miles!
1983 Alfa Romeo GTV6 (Guido)
1976 Jaguar XJS-saved a V-12 from the chevy curse, what a great engine!
1988 Cadillac Eldorado (better car than you might think!)
1988 Yamaha Venture (better than a Wing!)
1977 Suzuki GS750B
1976 Yamaha XS 650 (sold)
1991 Suzuki GSX1100G (Shafty Gixser)
1981 Yamaha VX920RH (Euro "Virago")
Solex Moped
1975 Dodge P/U camper


"Time spent in the company of a cat, a beer, and this forum, is not time wasted!"
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 05:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page