Originally Posted by jay_bob (Post 3720902)

I managed to get some time on the W210 last night with the computer just before the storms rolled in.

It works as advertised in the YouTube video I linked yesterday. I was able to make it blink the turn signals and it shows that the turn signals draw close to 5 A :eek: when lit. And I honked the horn, of course you have to go back into the menu to tell it to stop.

There are some online cautions about using a battery charger when in an extended session. I believe it, the battery dropped to nearly 12.0 V before I got done. The vehicle provides all the power for the multiplexer, and you also have to toggle the key on and off repeatedly as you go through the process, which also cycles your glow plugs.

Most of the W210 menu operations run through the HHT emulation software so it has to pull up a side window to load that. You can either click, arrow, or press the Fn keys on the keyboard to navigate through these menus.

I was reading around in the WIS and it makes mention of a feature on the non rain sensor equipped 210 wipers. If you have the switch on position II and you slow below single digit mph (like coming up to a light) the wipers automatically fall into intermittent mode until you speed up again. Or if you're already on intermittent then the time constant is increased. However my car does not seem to do this. There is a note in the WIS that says this feature may be disabled through version coding. I searched around the EIS and Front SAM menus and could not find any options to change this. Anybody seen or hear of this feature??

I did find the rain sensor equipped field, so if I ever figure out how to install a rain sensor then I know how to tell the OHP and SAM it's there. However from what I understand it requires a special version of the windshield with the lens factory bonded to the glass, plus the electronics that go behind the lens. So that may be a future project whenever it's time for a new windshield.

Also I would like to do the following, which I suspect are part of a version coding menu somewhere:
- change the dashboard clock to 24 hour mode (I prefer 24 hour time)
- change the outside temp and climate control temp displays to degrees C (keeping with the Euro theme, and to match the water temperature gauge)

If I get a chance to get connected to the W164 tonight or this weekend (it's trying to storm again tonight) then I will post more updates. Being that the W164 and the W211 share a lot of systems I am going to try to see if the flashing brake lights on hard braking option is there.

Originally Posted by iwrock (Post 3722567)

I've had an SDS for ~7 years, been super handy with all of the newer MBs I've had (and helped work on). I'm actually looking to update my setup to a new unit with SD Connect so I can do some work on chassis like the W212 and newer.

Some observations -

-Connect a battery charger, half of the cars I have done diag work/programming on have weak batteries... Low voltage will sometimes cause coding issues, or throw errors in modules.
-Clear any codes the module might have before you try to do any programming. I haven't seen it happen personally yet, but I've heard people say that sometimes a module won't take coding changes unless it's error free
-Don't be afraid to open menus, it will always ask you if you'd like to carry out coding changes if you did accidentally click something
-Some modules might have a different software version than other cars, so some features may or may not be available to you

If you've got any Q's, ask. I've used the SDS on many different cars, and also have some hands on experience with an actual MB SDS that was able to carry out SCN coding.

Originally Posted by ROLLGUY (Post 3783003)

I will have my rebuilt SBC module next week, and I need to get the actuation count reset. My local independent Euro auto repair shop charges $250 for this service. I am thinking about purchasing a STAR DAS system, as I am sure I will have other uses for it since there are at least four cars in my family/friends that will benefit from the availability of this tool. I have a hard time justifying paying $250 to hook my car up to their computer just to reset the SBC. Spending more on a STAR system seems like a better deal in the long run, and could basically pay for itself with four similar service costs. I sent a message to Gordy's Gadgets through ebay to find out if a system is available for purchase. As with others, I am leery about buying one from China. There is another vendor in New York with a similar system, but seems to be more $ than Gordy. However, if Gordy has none available, I suppose that is the best deal. Thoughts?

Originally Posted by shertex (Post 3783265)

Check with Module Master...I believe they reset the count for you, i.e. that it's internal to the unit.

Originally Posted by dieselbenz1 (Post 3722572)

Can you save the configuration of an entire SAM for future should you need it?

Originally Posted by shertex (Post 3722697)

Justin, are you aware of any manuals or documentation that may be of help to those of us getting acquainted with Xentry? I've done some searching but all I can find are scattered treads on how to make a few individual changes.

Thanks.

Originally Posted by shertex (Post 3723088)

Jay_bob, could I trouble to check something for me....since we have exactly the same version of Xentry? I am finding that, when I go under any car system to developer data, actuations, user-defined actuations, I get an error message. Initiatlly I was exploring under Drive because I wan't to see things like torque settings, pedal curve, vmax, etc... But I couldn't get there. And then I discovered I have the same inability in all car systems.

Gordy says that different versions of Xentry can have different routes to a given menu....but no luck so far.

Thanks.

Originally Posted by sixto (Post 3783248)

Wait for Gordy to have one. Works out of the box is worth every penny. Customer support in English can’t be beat. If SSD is an option, it’s worth every penny in reduced boot time. The nice thing about cloned SDS is it comes with WIS and EPC.

Sixto
98 E320s sedan and wagon

Originally Posted by iwrock (Post 3783647)

Oh, just saw this thread.

Rich, if you're interested I can send you my SDS to reset the actuation count on your SBC unit. Mine does have developer mode, which is needed to access the SBC actuation count.

I also have the directions that I can send along as well.

Originally Posted by ROLLGUY (Post 3783003)

I will have my rebuilt SBC module next week, and I need to get the actuation count reset. My local independent Euro auto repair shop charges $250 for this service. I am thinking about purchasing a STAR DAS system, as I am sure I will have other uses for it since there are at least four cars in my family/friends that will benefit from the availability of this tool. I have a hard time justifying paying $250 to hook my car up to their computer just to reset the SBC. Spending more on a STAR system seems like a better deal in the long run, and could basically pay for itself with four similar service costs. I sent a message to Gordy's Gadgets through ebay to find out if a system is available for purchase. As with others, I am leery about buying one from China. There is another vendor in New York with a similar system, but seems to be more $ than Gordy. However, if Gordy has none available, I suppose that is the best deal. Thoughts?