Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 03-19-2019, 09:50 AM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Vacuum modulator confusion

Bit of a long story but I have isolated a drop in vacuum between the modulator and top pipe, this is after Y junction to diaphragm on side of pump.

Going to have another go at remove/replace, one of the allan bolts is rounded off due to previous attempts despite lowering box.

Couple of questions;

Kent talks about (at 2.48) the cap retaining vacuum on both of these modulators, is this correct as there is no seal inside the cap which is fairly loose anyway.

If the cap does need to be air tight i can search around for another O ring and make good.

Thanks

https://www.youtube.com/watch?v=gM4KZvwsCW0

This video shows the cap/modulator in more detail, I would be surprised if the vacuum relied on the cap rather than say a small O ring around spindle.

https://www.youtube.com/watch?v=GIXR7gNXOws



__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)

Last edited by spock505; 03-19-2019 at 10:08 AM. Reason: added video
Reply With Quote
  #2  
Old 03-19-2019, 01:41 PM
tyl604's Avatar
Registered User
 
Join Date: Feb 2008
Location: Atlanta, GA
Posts: 3,639
If yours is like my '81 300SD, remember that the transmission needs vac only for downshifts. The vehicle is designed to have about 12inHg of vac at the VCV, but as you apply the throttle, the vac almost immediately drops to zero. Yes, it is theoretically a gradual release but if you hit the accelerator it goes to zero in about one second.


In fact you can drive with the line unhooked to the trans modulator and you will get smooth upshifts and clunky downshifts.

What exactly is your problem? What are the symptoms and why are you thinking vac modulator?
Reply With Quote
  #3  
Old 03-19-2019, 02:07 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Thanks, its been an ongoing fault which I visit every now an then hoping to find a solution.

1st and 2nd shifts are lumpy, valves (B1,2 K1) have been changed along with 3 ATf flushes , attaching aMytivac to the T piece (pump top) shows a rapid fall in vacuum to the modulator.
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #4  
Old 03-19-2019, 02:35 PM
Diseasel300's Avatar
Registered User
 
Join Date: May 2016
Posts: 6,025
The modulator should hold vacuum just like any other vacuum pod. Supposedly the cap does make a difference with vacuum holding, but both my SDL and SD will hold vacuum without it.

If the bowden cable is adjusted properly, the throttle linkages are adjusted properly, and the engine is making the correct power, even with no vacuum you should have a reasonable (but firm) shift. If you're having sloppy shifting or hunting, the modulator likely isn't your culprit, something else is out of adjustment or worn out.
Reply With Quote
  #5  
Old 03-19-2019, 02:44 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Just went out to try unplugging the modulator altogether, upshifts are a bit firmer as if there is no cushion, downshifts appear the same.

As another sort of test, plugged the black vacuum line (which goes to the box via Y shaped pump fitting) directly into pump, this made a big difference, all shifts pretty much normal.

Wondering if its just lacking vacuum due a crack or something, plugging into pump direct help boost vacuum?
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #6  
Old 03-19-2019, 02:48 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Quote:
Originally Posted by Diseasel300 View Post
The modulator should hold vacuum just like any other vacuum pod. Supposedly the cap does make a difference with vacuum holding, but both my SDL and SD will hold vacuum without it.

If the bowden cable is adjusted properly, the throttle linkages are adjusted properly, and the engine is making the correct power, even with no vacuum you should have a reasonable (but firm) shift. If you're having sloppy shifting or hunting, the modulator likely isn't your culprit, something else is out of adjustment or worn out.
Diesel, not convinced about the cap as it needs to be removed for adjustment, if it was part of vacuum circuit all would be lost making adjustment impossible.
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #7  
Old 03-19-2019, 03:23 PM
tyl604's Avatar
Registered User
 
Join Date: Feb 2008
Location: Atlanta, GA
Posts: 3,639
He is right. If your modulator will not hold a vac, it is bad. What color vac modulator do you have? It must hold a vac to work properly.

On the original 1981 vac modulators, the cap was just a black rubber cap. You removed it, turned the T pin, and replaced the rubber cap. The rubber cap was to hold vac.

If your Mityvac will not pump up and hold a vac by placing it on the trans modulator nipple, the trans modulator is bad. Or maybe it was installed cockeyed.
Reply With Quote
  #8  
Old 03-19-2019, 03:55 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Quote:
Originally Posted by tyl604 View Post
He is right. If your modulator will not hold a vac, it is bad. What color vac modulator do you have? It must hold a vac to work properly.

On the original 1981 vac modulators, the cap was just a black rubber cap. You removed it, turned the T pin, and replaced the rubber cap. The rubber cap was to hold vac.

If your Mityvac will not pump up and hold a vac by placing it on the trans modulator nipple, the trans modulator is bad. Or maybe it was installed cockeyed.

Yup, its deffo bad, there is some resistance there but gauge drops from half to zero in maybe 3-5 seconds.

Dealer looked up correct unit which is brown (but looks orange), three day delivery door to door from Germany at around $100.

Weather is starting to turn here, will get the old one off next week or two and report back -

Last attempt removed trans cross member which wasn't enough, this time will take off engine mounts letting the engine rest on wood - hopefully this is enough to get that last bolt.

Bowden cable has been tweaked to hold onto gears longer, will need to re-adjust - have the procedure somewhere but need pressure gauge fro proper job.
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #9  
Old 03-19-2019, 04:04 PM
tyl604's Avatar
Registered User
 
Join Date: Feb 2008
Location: Atlanta, GA
Posts: 3,639
You might consider giving our sponsor Pelican a call. Maybe they have one. Also think Bergstrom has them.
Reply With Quote
  #10  
Old 03-19-2019, 04:07 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
It would be great to support Pelican but unfortunately other side of pond in UK, just came across this excellent Corteco manual for 722.3, 4

https://www.scribd.com/doc/24267811/Mercedes-722-3-722-4
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #11  
Old 03-21-2019, 06:39 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Going to have a goo at pulling this out tomorrow, not much room between cross member and sump for lowering - thinking of undoing and removing one engine mount then twisting engine and box enough to access stuck bolt, is there anything that might snag ?

Is the gear selector linkage cable or rods, that might cause a problem if it is, cheers
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #12  
Old 03-22-2019, 09:27 AM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Okay, four hours later and one vac modulator removed - the above approach worked well loping the engine to one side, i did have to undo rear trans mounts also.

Bit of good news also, the modulator looks fine saving $100 - the loss of vacuum stems from having the T bar rotated left, i assume at this position the modulator is discharging vacuum at that setting, turned to the right several turns reduces the drop to almost nothing -

..here's the key, it uses the hole which the T piece sits i as a vent, covering this stops all discharge at any setting, this makes sense as there is no other visible vent.
__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
  #13  
Old 03-22-2019, 10:36 AM
vwnate1's Avatar
Diesel Dandy
 
Join Date: Nov 2005
Location: Sunny So. Cal. !
Posts: 7,717
Thumbs up

Subscribed .
__________________
-Nate
1982 240D 408,XXX miles
Ignorance is the mother of suspicion and fear is the father

I did then what I knew how to do ~ now that I know better I do better
Reply With Quote
  #14  
Old 03-22-2019, 11:40 AM
Registered User
 
Join Date: Feb 2016
Location: North New Jersey
Posts: 431
In an attempt ot get my shifts perfect a few years ago I dove deep into the modulator along with other components. After testing the trans pressure port with a gauge (there is a good guide on here somewhere) I was somehow convinced I should change it. I did have a small vac leak - though it was also obvious the original cap was cracked and brittle. I should have started with the cap but....

Gaining enough access in situ and swapping out my modulator in my 300D was physically the hardest thing I've ever done on my car. disconnected drive shaft at flex plate to be able to shift the trans to side more. In the end, the new (correct color, genuine mercedes part) one would not seat correctly and not leak no matter what. It was pure hell for like 2 days, destroying one new modulator in the process. I just reverted to old original modulator and then put on a new rubber cap. Doesn't leak vac, good enough for me. I will never try that again!
__________________
Andrew
Montclair, NJ
--------------
1982 300D Turbo
120k
Petrol Blue Green
Reply With Quote
  #15  
Old 03-22-2019, 04:59 PM
spock505's Avatar
Registered User
 
Join Date: Nov 2007
Location: Blighty
Posts: 1,388
Thumbs up Update & conclusion

Fitted parts in reverse order in the dark, all good - used 10mm captivated bolts instead of Allan bolts, tbh probably made it harder due to recess and steep angle.

For anyone reading wanting to test the modulator or diaphragm integrity, this can be easily undertaken with the part insitu.

Mark the current position of T bar then rotate fully clockwise, at this point the valve will be closed leading to 100% seal, the reverse is true anti-clockwise.

As I understand it, the operation of the modulator affects both the hardness and response of shift points, this is achieved by regulating the vacuum against the spring loaded diaphragm - the vacuum varies according to RPM of engine, the modulators response to this regulated by the valve which the T bar sits in, clockwise closes the valve making the response to vacuum load far more responsive, anti-clockwise no vacuum load and possible no modulator intervention.

The cap has no bearing on the modulator operation other than to provide fine adjustment and secure T bar in place, if this were fully sealed it would close off the valve altogether.

Couple of points of note, whilst you can check the vacuum in situ you cannot see the piston operation, in my case it was almost certainly stuck or at best slow to operate – this could be down to the setting which essentially left it in one place rather than moving back and forth.

End result, different car – silky smooth changes in unison with the engine, before it changed up just one after the other without reference to much else.

__________________
David


1996 Mercedes S124 E300TD - 129k - rolling restoration project -

1998 Mercedes W210 300TD - 118k (assimilated into above vehicle)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 08:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page