Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 03-04-2003, 09:49 PM
dap dap is offline
Registered User
 
Join Date: Aug 2001
Posts: 14
Clutch adjustment on my 240D?

OK, I;m a rookie to this part of my car. How does the hydraulic clutch work? Can it be adjusted?

It has very little "peddle " left. I only have to push the peddle a small amount to engage it and sometimes it is hard to shift into reverse or it grinds as I try to go into reverse.

What to do?

__________________
Phil
1985 300TD, 180K
1980 240D. 335K
Reply With Quote
  #2  
Old 03-05-2003, 01:37 AM
Moderator
 
Join Date: Jul 2001
Location: Woolwich, Maine
Posts: 3,598
dap,
There is little need to adjust a hydraulic clutch, so there is no ready provision to do so, provided it is installed correctly. It works by having a small cylinder connected to the pedal, so when you push it down, the piston in the cylinder displaces a fixed volume per unit of stroke length (edit). This volume change is forced into the slave cylinder at the clutch mechanism and pushes a piston out to activate the mechanism to release the clutch. Letting the pedal out reverses the process. As the clutch wears the system volume increases and this is made up with fluid from the brake reservoir rear compartment. This way the pedal stroke and the clutch mechanism stroke remain in the same proportion as the clutch wears, so you do not need to adjust.

You should make sure the rear part of the brake fluid reservoir is full though as that is what feeds the clutch hydraulic cylinders and if it gets air in it, or there is a leak, the performance of the clutch suffers. Air is compressible and any air upsets the pedal stroke lenfth (edit) to clutch activating mechanism response proportionality.

If there is not enough clutch left, and it is about to slip, you should get the opposite response, meaning a little inward motion of the pedal and you should completely release the clutch - no grinding as you reported. So it makes me think there is air in there, which takes most of the pedal travel to compress.

Bleeding is a bit of a problem sometimes. But you must address how the air got in there first. In my experience, once that is fixed and the reservoir is full of fluid, the unit should self bleed as you use it. I have never had a problem with air in a sealed system, only in systems with leaks. Remember, if air can get in, fluid can leak out. And the opposite. Good luck, Jim
__________________
Own:
1986 Euro 190E 2.3-16 (291,000 miles),
1998 E300D TurboDiesel, 231,000 miles -purchased with 45,000,
1988 300E 5-speed 252,000 miles,
1983 240D 4-speed, purchased w/136,000, now with 222,000 miles.
2009 ML320CDI Bluetec, 89,000 miles

Owned:
1971 220D (250,000 miles plus, sold to father-in-law),
1975 240D (245,000 miles - died of body rot),
1991 350SD (176,560 miles, weakest Benz I have owned),
1999 C230 Sport (45,400 miles),
1982 240D (321,000 miles, put to sleep)
Reply With Quote
  #3  
Old 03-06-2003, 09:23 PM
franklyspeaking's Avatar
Registered User
 
Join Date: Dec 2001
Location: Moulton, Alabama
Posts: 396
Quote:
It has very little "peddle " left. I only have to push the peddle a small amount to engage it
You push to disengage and let out to engage. So which is it, lack of engagement or disengagement? Like Jim says, grinding is consistent with the clutch not disengaging. It sounds like you have a problem with air in the line, a low hydraulic level, or a failing master or slave cylinder. Also, a worn clutch would slip and so a quick push of the accelerator would yield an RPM increase, but little speed increase.

Good luck.
__________________
1976 240D
1987 560SL
2007 E320 Bluetec
1998 C280 (now son’s car)
1982 240D Manual - Sold
Reply With Quote
  #4  
Old 03-06-2003, 10:24 PM
Coming back from burnout
 
Join Date: Jun 1999
Location: in the Pacific Northwest
Posts: 2,274
I had the same problem last week...

Crawl under the car with a Squirt Can Oil Pump bottle full of Brake Fluid with a rubber hose attached to its outlet.. Loosen the bleed valve on the slave cylinder. Attach the hose to the slave cylinder and pump some 50 squirts, seriously. Tighten up the bleed valve. 100% gaurentee this will fix the problem. Had same problem EXACT same problem last week...
Reply With Quote
  #5  
Old 03-07-2003, 08:52 PM
dap dap is offline
Registered User
 
Join Date: Aug 2001
Posts: 14
Yes, I should have used the word "disengage" in my discription. No, the trans. does not slip at all.

I hope to work on it next Tue. and will try your idea.

Two questions.
1. What do you mean by a "squirt can oil pump"?
I assume anything to squirt oil will work.
2. When I crawl under the car, where is the slave cylinder and what does it look like?

thanks!
__________________
Phil
1985 300TD, 180K
1980 240D. 335K
Reply With Quote
  #6  
Old 03-07-2003, 11:31 PM
Coming back from burnout
 
Join Date: Jun 1999
Location: in the Pacific Northwest
Posts: 2,274
Call me at (609) 254 6255 and I will be glad to walk u through this.

A squirt can oiler is any cheap pump oiler you can find at a Hardware Store. You will also need about 2 feet of rubber hose 5/16" Inside diameter.
Fill the squirt gun with Brake Fluid.

Attach one end of ther Hose to the end of the squirt gun and attach the other end to the bleed valve on your slave cylinder.. if you are underneath your car you will note that this slave cylinder sits on the driver side of the transmission.

Use a small 8mm wrench to open the bleed valve. Start pumping like crazy. Tomorrow I will try to send u digital photos of this procedure since i will be doing it for a friend.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 06:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page