Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-06-2003, 09:13 PM
Registered User
 
Join Date: Oct 2002
Location: Northern California
Posts: 188
still more tranny questions

O.K. I've followed every test procedure I could find on this site for tuning the tranny on my 83' 300D but my problem still exists. At low speed and light throttle there is a very loud clunk on the 4-3 downshift. At higher speed and heavier throttle it will shift really nice. I've tried backing out the modulator and it seems like it doesn't do anything. Is the modulator bad? Any ideas? Thanks very much!

Reply With Quote
  #2  
Old 08-06-2003, 11:48 PM
Registered User
 
Join Date: Sep 2001
Location: central Texas
Posts: 17,281
So you found the Steve Brotherton site and followed his advice?
Reply With Quote
  #3  
Old 08-06-2003, 11:57 PM
adamb's Avatar
Registered User
 
Join Date: Jul 2001
Location: Chapel Hill, NC
Posts: 321
Helo, I have a 1985 300D and had the exact same problem which I spent no small amount of time and money to fix. The culprit wound up being a small pin-hole leak in the vacuum diaphram on my turbo. The symptoms suggested to me that it could be a rear end going bad, bad center u-joint, or something else mechanical. I was amazed that fixing this vacuum leak corected the problem.
Good luck! Adam Bush
Reply With Quote
  #4  
Old 08-07-2003, 07:18 AM
Registered User
 
Join Date: Oct 2002
Location: Northern California
Posts: 188
Yes I've followed the advice on Steve's site.

Any advice on how to go about checking for this vacuum leak at the turbo? My symptoms are exactly like what you descibe, u-joint or bad differential. I'm willing to try anything at this point. Thanks very much.
Reply With Quote
  #5  
Old 08-07-2003, 02:28 PM
adamb's Avatar
Registered User
 
Join Date: Jul 2001
Location: Chapel Hill, NC
Posts: 321
With your car being a 1983 model, you probably don't have the same diaphram that I have on the turbo, as mine is a cali model and it is for emissions.
The vacuum leak could come from anywhere, so I would start by working backwards, first starting at the modulator. I would buy a Mity Vac (or equivelant) and pull vacuum up to 20psi at the line going to the modulator. Then I would let it sit for a minute to see if it holds. Then, I would work this way backwards until I came to a "T" of some sort, and disconnect and plug anything not related to the tranny modulator vacuum while still ensuring the source of the vacuum to the modulator is still connected, then drive it and see what happens. Thsi is what I did and tranced it to that faulty diaphram on my turbo. I would bet that your problem is vacuum related as it seems the vast majority of tranny issues are.
I hope this helps, Adam Bush
Reply With Quote
  #6  
Old 08-07-2003, 09:25 PM
Registered User
 
Join Date: Oct 2002
Location: Northern California
Posts: 188
Thanks Adam,

This is basically what I have started to do. I found a huge vacuum leak at the EGR and also at the thermo switch to the EGR. I've got that line that connects to those plugged for now. I've replaced most of the rubber connectors and vaccum lines as well as the vacuum switches and the bleed off valve. My modulator seems to hold vacuum just fine. I've even replaced the main brake booster vacuum line. I suspect my modulator may be faulty somehow, as I just backed it off one complete turn and it has only slightly improved the shift quality. I'm under the impression that the modulator is more sensitive than that?
Reply With Quote
  #7  
Old 08-07-2003, 11:56 PM
adamb's Avatar
Registered User
 
Join Date: Jul 2001
Location: Chapel Hill, NC
Posts: 321
Modulators are very inexpensive and are easy to replace, so it wou be a bad idea to replace yours. This would be a good time to change the filter and fluid if you haven't already as well.
There is also a shift improver kit that you can buy for 50 bucks which consistc mostly of springs inside the valve body. I have bought one for my car but haven't put it in yet. Maybe this weekend I will and post back the results - I bought it to fix the 1-2 upshift primarily.
Since you found the EGR leak, has the clunk on downshift gone away?
Reply With Quote
  #8  
Old 08-08-2003, 07:15 AM
engatwork's Avatar
Registered User
 
Join Date: May 2000
Location: Soperton, Ga. USA
Posts: 13,648
I currently have a vacuum leak issue with my door locks and if I do not lock the doors after getting underway I get some pretty abrupt shifts. Got to make the time to resolve it over the next couple/few weeks.
__________________
Jim
Reply With Quote
  #9  
Old 08-09-2003, 08:19 PM
Registered User
 
Join Date: Oct 2002
Location: Northern California
Posts: 188
Since blocking off the EGR, adjusting the bowden cable and backing the modulator off one full turn the shifts are better but still not perfect. The clunk on the 4-3 still occurs, although not as frequently and all other shifts are smoother. However, it flaired on me at the 2-3 upshift the other day!!
Seriously considering going for a stick shift conversion!

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 06:45 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page