|
|
|
#1
|
|||
|
|||
Turbo Failure/wear Verification
I have a 1993 300SD with 214,000 miles on it.
I have a lack of power. I recently traveled to West Virginia from Connecticut and the car could not hold road speed going through the mountains (interstate). I noticed a little some oil leakage at the crossover at the intake manifold. There also appears to be some oil coming from the turbo side of the crossover (although it is hard to tell). Is there anyway I can inspect the turbo to determine whether or not it is worn? Are there other things to check, too? Are there any DIY procedures I can use? Thanks, -Ralph
__________________
Ralph Burnette 1993 300SD (286k + miles) 2000 SL500 2001 ML320 |
#2
|
||||
|
||||
Try a search of the Diesel Discussion using these words:
'turbo check', 'turbo function', turbo operation'...lots in here about that stuff.
__________________
Never a dull moment at Berry Hill Farm. |
#3
|
|||
|
|||
When I hear your symptoms, the first thing that comes to mind is that you got a bad batch of fuel. I assume you've already swapped out the filters/checked for algae? Is there a particular reason you suspect the turbo?
__________________
Tjohn 82 300 SD 77 450 SL (gone) |
#4
|
|||
|
|||
Power seems inconsistent. On long grades where I am running
at 70MPH or so, the car slows down to 60. I have to force a downshift to keep roadspeed up to a reasonable level. In addition on a short upgrade (starting from stop), I seem to have no power; no real pull. In addition, there was some oil seepage at the crossover and the intake manifold, indicating some blowby or that the turbo seals were leaking. It is possible that my mechanic ovefilled the oil a little during the oil change just before I left for the trip. I checked the turbo. There is virtually no play in the shaft and it spins freely without any catching, etc. so I am not sure that it is the turbo anymore. When I was looking at the turbo, I noticed that the vacuum line to the EGR valve wasn't down all the way on a connector to another hose. In any case, it is fairly easy to slide in and out. I am looking for a pump to do some vacuum tests which is next in the plan. On the opposite side of the engine near the firewall there is a sensor where a number of vacuum lines connect, including one coming off the intake manifold. Does anyone know how to test it? Thanks, -Ralph
__________________
Ralph Burnette 1993 300SD (286k + miles) 2000 SL500 2001 ML320 |
#5
|
||||
|
||||
Yep, if the onset of this problem was reasonably fast it's probably fuel. Change the filters and run some Power Service or other diesel additive through.
__________________
Never a dull moment at Berry Hill Farm. |
#6
|
||||
|
||||
At the risk of asking a stupid question, what if the symptoms did not "appear suddenly"? The reason I ask is that sounds like the performance of the 300TD I just bought. I thought it was just "normal" diesel operation. No?
kma
__________________
74 Porsche 914 2.0 - 92k and counting 85 300 TD - 263k and counting 83 300 TD - 190k and counting 74 Harley Davidson Superglide - 38k and counting 68 Harley Davidson Sportster - currently in kit form |
#7
|
|||
|
|||
Check the white plastic line from the center of the manifold (92 350 SD, 603 engine) or the rear of the intake manifold (617 engine) for leaks. The rubber bits that connect the plastic line are old and hard by now, plan on replacing all of them in the engine compartment.
Also check by blowing down the line that it holds pressure. If not, check the switchover valve on the firewall for leaks. It goes (on the 603) from manifold to switchover to ALDA (aluminum squarish box on the injection pump) to the blue vac amplifier on the driver's side fender for the tranny. I'd bet you have a fault in the pressure sensing lines, so you don't have pressure on the ALDA and no extra fuel. That 603 shouldn't have any trouble at all holding any highway speed you want at any altitude! Peter
__________________
1972 220D ?? miles 1988 300E 200,012 1987 300D Turbo killed 9/25/07, 275,000 miles 1985 Volvo 740 GLE Turobodiesel 218,000 1972 280 SE 4.5 165, 000 - It runs! |
#8
|
|||
|
|||
93 300SD = Bent Connecting Rods.
Ken300D
__________________
-------------------------- 1982 300D at 351K miles 1984 300SD at 217K miles 1987 300D at 370K miles |
#9
|
|||
|
|||
Quote:
Ralph - did you check along the lines Peter suggested yet?
__________________
Tjohn 82 300 SD 77 450 SL (gone) |
#10
|
|||
|
|||
I thought perhaps the connecting rods could bend at any time during the life of the car - depending on when it finally ingested EGR-induced chunks of carbon.
And then I thought further that bent connecting rods might result in reduced performance. Maybe the symptoms are more quickly obvious when you have bent connecting rods. Ken300D
__________________
-------------------------- 1982 300D at 351K miles 1984 300SD at 217K miles 1987 300D at 370K miles |
#11
|
|||
|
|||
If bent rods were the result of ingesting intake manifold carbon/sludge then 603.96 and 602.96 engines would suffer from it as well (as they carbon up JUST like the 603.97 engines) and the rebuilt 603.97 engines would be doing it by now! That's not happening. The original OM603.97 engine design was the problem. With new rods, they seem to work just fine. OM603.97 engines almost never present with low power. High oil consuption/smoke or broken rods are the usual peresenting symptoms. Most low power conditions are because there is either insufficient boost activating the ALDA (and fuel enrichment) the ALDA aneroid is broken or the overboost circuit has been activated.
Marshall |
#12
|
|||
|
|||
Quote:
Go to 350SD, burning oil SECOND STAGE ENGINE
__________________
1987 300SDL (324000) 1986 Porsche 951 (944 Turbo) (166000) 1978 Porsche 924 (99000) 1996 Nissan Pathfinder R50 (201000) |
#13
|
|||
|
|||
Welcome aboard..
Dr. Booth - great to see you here, hope you stay awhile. Ladies and Gents, as a lurker on the MBZ.org diesel email list, let me say that we're in for a treat if Marshall is going to hang around and share his knowledge.
__________________
Tjohn 82 300 SD 77 450 SL (gone) |
#14
|
|||
|
|||
[QUOTE]Originally posted by DslBnz
[B]Check my posts and follow my progress. Maybe I'll be the first one to have one of the new engines blow up. I'm sure it's NO consolation when your engine is drinking oil, but the failure rate for the rebuilt 603.97 engines is similar to other MB diesels (maybe 1% give or take) while the original engines had a failure rate MUCH higher than any MB engine I've ever heard of. Marshall |
#15
|
|||
|
|||
Do you know of any 350's with those new engines with over 178K miles on them? That would mean you'd have to find a 350 with around 240 - 300K miles on them (how many are there, anyway?) I've seen original engined 350's go 220K miles before any rod-bending. It can happen at any time, apparently, and it evantually does. How many 350's out there in excess of 400K miles on the original engine? None I can document, yet.
I am not saying my engine has failed yet, but chances are, it will. I do not know of anybody in my area who even OWNS a 350 because they are so rare. How do you know they are lasting 3 - 400K miles, no prob(and beyond?)? The engines are just too new, and the cars are too rare. If you could tell me about somebody who actually has a 2nd 350 engine with that kind of miles, I would be extremely interested in looking at it, out of curiousity. I've seen several 300's (OM603)with over 400K miles, and some had close to 500K miles. Still running, with the third generation heads, of course! My 300SDL doesn't burn a drop of oil! Sorry if I sound rude; I'm upset, and am looking for a logical solution to a very challenging enigma.
__________________
1987 300SDL (324000) 1986 Porsche 951 (944 Turbo) (166000) 1978 Porsche 924 (99000) 1996 Nissan Pathfinder R50 (201000) |
Bookmarks |
|
|