|
|
|
#1
|
||||
|
||||
Is it bad to downshift?
guys,
i wanted to ask if downshifting is bad for the car. whenever i do it, there just seems to be a lot of engine noise in a bad way. it just seems like gas cars take it in stride and mine hates it. i'm on lunch break and it is more fun that getting rained on outside. besides, my finger just got bit by a kid who didn't want me cleaning his teeth. ugh. jt
__________________
Jennifer 90 350sdl |
#2
|
||||
|
||||
Is this an automatic or manual transmission?
In any case, using the engine to slow the car down is not adviseable. The brakes are specifically designed for that, and brake parts are a lot cheaper to replace than engine, clutch, or transmission parts. If you're talking about using a lower gear to hold the speed down while you're descending a mountain, that's not so bad as long as you don't overrev the engine. The dots on the speedometer indicate the maximum safe speed for each gear.
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#3
|
|||
|
|||
you be double clutching? if manual.
|
#4
|
|||
|
|||
jt,
Downshifting is good for control when you do it right and should not adversely affect the rest of the car in any way. If you are coming to a stop, it is likely easier on the clutch to use the brakes though, and since you have no use for the extra power available at the higher rpm after you downshift when you are coming to a stop, it makes more sense to use the brakes. You will likely get a number of responses to this question, but engine noise, unless there is a loud and not healthy sounding metallic clanking, is not unusual. Most of the normal noise is really exhaust system noise in most cases, and it gets very loud veryt quickly as the engine speed increases. Not much you can do about it, so most of us just accept the noise and drive on. My daughter drives our 1982 240D very hard, at high rpm (she virtually redlines before shifting in every gear), and the car runs extremely well. It has 311,000 miles now, and she drove it back and forth across the country last summer. It starts in 20*F weather without any hesitation or plug in water heater help, etc. So, downshift when you need the extra power or control, and take care not to slip the clutch or use the clutch as a brake - they cost a lot more to repair/replace than brake pads - and the car will probably be rejuvenated. Good luck, and next time a kid bites your finger give him a squirt of Tabasco sauce or something. They are like puppies and need to be taught to connect bad behaviour with bad experiences. Jim
__________________
Own: 1986 Euro 190E 2.3-16 (291,000 miles), 1998 E300D TurboDiesel, 231,000 miles -purchased with 45,000, 1988 300E 5-speed 252,000 miles, 1983 240D 4-speed, purchased w/136,000, now with 222,000 miles. 2009 ML320CDI Bluetec, 89,000 miles Owned: 1971 220D (250,000 miles plus, sold to father-in-law), 1975 240D (245,000 miles - died of body rot), 1991 350SD (176,560 miles, weakest Benz I have owned), 1999 C230 Sport (45,400 miles), 1982 240D (321,000 miles, put to sleep) |
#5
|
||||
|
||||
I was told years ago that excessive downshifting to slow a vehicle is hard on the differential. I guess it puts a reverse load on the pinion bearings and/or gears, or something like that. But I've never had that confirmed from another source.
__________________
past MB rides: '68 220D '68 220D(another one) '67 230 '84 SD Current rides: '06 Lexus RX330 '93 Ford F-250 '96 Corvette '99 Polaris 700 RMK sled 2011 Polaris Assault '86 Yamaha TT350(good 'ol thumper) |
#6
|
||||
|
||||
I am quite certain that it does very little harm to a vehicle. Earlier, I used to downshift quite a bit. I still got 250 kmi from the clutch and I have now owned the car for over 300kmi. I do not have any noticeable damage from downshifting. I figure that as I am at over 370kmi with about 310kmi of it driven by me, if my driving style was poor or if I did things which were damaging to the car, the problems would have shown by now -- especially on a 60x which the board seems not to like as compared to a 61x (I do not share this feeling).
__________________
Jovan '84 (11/83) 190D 2.2 5-Speed; Silver/Blue; Motor No. 00354, 402k mi (340+kmi mine) '89 Porsche 911 Turbo Coupe; Black/Black; 53kmi '05 BMW 530i 6-Speed; 302kmi '19 Range Rover; 30kmi |
#7
|
|||
|
|||
this be a 240d. may be the downshifting is contemplated for keeping up with traffic.
|
#8
|
||||
|
||||
I don't think down-shifting our diesels is a good idea. Holding the speed on a downgrade is a different matter, though.
Back in the '50s and '60s everyone racing sports cars downshifted. If you didn't, the brakes wouldn't last the race. More modern brake materials have changed all that. Most racers now only downshift to the gear they need exiting the corner rather than using the engine to slow the car. Brake pads and linings are definitely cheaper than rebuilding engines or transmissions. Just my $.02, Wes |
#9
|
||||
|
||||
Isn't he talking about hitting the kickdown switch, i.e. downshifting for better acceleration? This is how I read the first post-
__________________
94 E320 71 350SL |
#10
|
||||
|
||||
She hasn't answered my question - auto or manual. So everyone is guessing. Jen, we're sitting around with nothing to do but answer your questions. C'mon, you have to keep up with us!
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#11
|
||||
|
||||
Ooops! She!
Sorry, Jen. You must clarify transmission- rickmiley's right- we all are sitting around with nothing better to do, trying to answer your question... JAS
__________________
94 E320 71 350SL |
#12
|
|||
|
|||
Being in the appropriate gear for your speed and road conditions is the way to think.
Unless you are racing or driving hard for a reason this normally means using the highest gear possible with out labouring the engine. Maximum torque is normally at low revs on older diesels. However as previously stated by others, changing down a gear for long hill descents will allow the engine to do some of the braking. Proper use of the clutch and gearbox will not cause unusual wear. After all this is what they are designed to do. If on the other hand it's an auto box just let the box do the work, but downshifting with the lever is still useful for descents.
__________________
Brian 1995 E300 Diesel 124T - 210k |
#13
|
||||
|
||||
sorry guys. this is not my day.
the car is a manual. don't you just love a girl who insists on a manual car? jen ps. not my day= got bit again. different kid. dang the pics from the party came out. ugh. like i said , not my day
__________________
Jennifer 90 350sdl |
#14
|
||||
|
||||
Quote:
__________________
Rick Miley 2014 Tesla Model S 2018 Tesla Model 3 2017 Nissan LEAF Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro Chain Elongation References |
#15
|
|||
|
|||
I'm a strong believer in downshifting and the key to avoiding stress on the transmission, whether auto or manual, is to match the engine speed of the next gear before completing the downshift. If you just release the clutch or pull the shift lever back with an auto tranny without pressing the throttle appropriately, then yes, that puts stress on your driveline. Otherwise it's just like upshifting, provided you don't overrev the engine.
Downshifting is very useful on long downgrades to avoid overheating your brakes and possibly killing yourself. Also while driving on snow or ice it's safer than applying the brakes if you do it smoothly and not downshift too low.
__________________
2004 VW Jetta TDI (manual) Past MB's: '96 E300D, '83 240D, '82 300D, '87 300D, '87 420SEL |
Bookmarks |
|
|