Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion > Diesel Performance Tuning

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 01-22-2012, 09:38 AM
Registered User
 
Join Date: Jan 2012
Posts: 7
Turboing OM616, technical questions

Hi, to all.

I am thinkig about turboing 240D, and i have few questions about it.

1. oil to feed turbo.

solution


This is solution from member Graminal95,
what do yout think about it, what restriciton should be made, so that the oil pressure don't drop too much, but there would be enough oil for lubrication.

In europe there is not easy to find back plate of oil housing for 300DT.
There is option for drilling original back plate, maybe it is better solution?
here is picture of back oil plate


2. Oil cooler

would it be good souliton if oil from turbo, goes through some kind of cooler, that have horizontal lines, so that there would be no, or very low flow restriction.

what about adding original oil cooler from 300D, is it possible to drill holes in front of oil filter housing, and put oil cooler?



3. safe limit of EGT?
i guess that the safe limit whould be about 1000F.


Thanks a lot.
If you have any other suggestion please write, thanks!

Reply With Quote
  #2  
Old 01-26-2012, 05:22 PM
Registered User
 
Join Date: Jan 2012
Posts: 7
anyone?
Reply With Quote
  #3  
Old 01-26-2012, 06:25 PM
Registered User
 
Join Date: Jul 2008
Location: virginia
Posts: 496
There should be a restricted oriface right at the turbo, look at your turbo where the oil goes, and you will see only a tiny hole for the oil to go in. No need to restrict it anywhere else.

I think the metal on the back plate of a non turbo engine may be a bit thin to allow drilling and tapping for an oil line. You may need to weld a bung on it.

I don't see any need to cool the return from the turbo. Although you may want to change the oil cooler for one from a 300. So far I have not. Perhaps put a oil temp gauge on, this would be in the oil pan.
__________________
1977 240D turbo
Reply With Quote
  #4  
Old 01-26-2012, 07:35 PM
Registered User
 
Join Date: Nov 2011
Posts: 15
1000F seems good. 47 dodge has it right. You need todrain the oil in the most vertical route possible to the oil pan.

Ed
Reply With Quote
  #5  
Old 01-27-2012, 06:15 PM
Registered User
 
Join Date: Jan 2012
Posts: 7
thanks for reply!

yes there is a restriction on turbine, but we will se if that is enough, so my oil pressure dont drop too much.

On EU models, only om617 have oil cooler, 615 and 616 doesn't have it.
I will have to see will it work without it.

i will install oil temp gauge and watch for temperature, for mineral oil I will try not to pass 240F.

Thanks, any suggestions are welcome!
Reply With Quote
  #6  
Old 01-27-2012, 10:21 PM
Registered User
 
Join Date: Jul 2008
Location: virginia
Posts: 496
My oil pressure is staying 20-25 psi at idle. And I do also have a bypass filter taking a little extra oil.

Generally 1250, continous, 1500 for short times is considered ok, but without piston oil squirters, lower would be wise. Right now mine will not go above 1000 with my current ip tune. It only made it this high pulling a trailer. normal driving about 850 is about as high as it will get when going uphill.
__________________
1977 240D turbo
Reply With Quote
  #7  
Old 01-29-2012, 09:47 AM
Registered User
 
Join Date: Jan 2012
Posts: 7
Ok, then it is time to run some big modification and test it.
I hope that nothing will go wrong, but we will see.
Thanks!
Reply With Quote
  #8  
Old 02-01-2012, 02:56 PM
Registered User
 
Join Date: Jan 2012
Location: Seattle
Posts: 40
Is there a way to add the little vacuum thing on the IP to increase fuel when the turbo is on boost, like the OEM turbo models? I've thought that adding a turbo to a 240 would be a good idea, I just never looked into this aspect. I've driven a 240 with a turbo but it was air only, and the power difference was hardly noticeable. How do you get the extra fuel in?

Kevin
Reply With Quote
  #9  
Old 02-01-2012, 06:46 PM
Registered User
 
Join Date: Jul 2008
Location: virginia
Posts: 496
Yes you can change the thing on top to one from a turbo charged 617. This is the Alda. I did not bother with adding an alda.

However you still need to have the ip(injection pump) recalibrated for more fuel to see any real gain from a turbo.
__________________
1977 240D turbo
Reply With Quote
  #10  
Old 09-10-2012, 07:46 PM
Registered User
 
Join Date: Jan 2012
Posts: 7
what type of diesel injectors do you use on OM616?
are there any benefits from using one from OM617 Turbo
Reply With Quote
  #11  
Old 09-11-2012, 08:18 PM
10mm MW
 
Join Date: Sep 2008
Location: Michigan
Posts: 767
Quote:
Originally Posted by OM61X View Post
what type of diesel injectors do you use on OM616?
are there any benefits from using one from OM617 Turbo
I am getting prices for a higher flowing nozzle than the ones that are currently use on MBs, from both Bosio and Monark.

As soon as the prices come in I will be putting in an order for my 616turbo and 617aturbo.

A higher flowing nozzle will help to reduce the injection time allowing more fuel to be delivered while staying with in EGT limits. If you really want to go for it, a 10mm IP will get you to the top of the class.
Reply With Quote
  #12  
Old 10-08-2012, 07:32 PM
Registered User
 
Join Date: Jan 2012
Posts: 7
is there any good if i use bigger injector nozzle than standard.

let say that the original is (bosch)SD 240, what wolud be if i put SD 265
that is used in w124 300DT or in w140 350 DT
Reply With Quote
  #13  
Old 10-08-2012, 10:13 PM
Registered User
 
Join Date: Jul 2008
Location: virginia
Posts: 496
I did use injectors from a 617a, and the pre chambers too.

__________________
1977 240D turbo
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page