Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Mercedes-Benz SL Discussion Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 04-14-2005, 10:54 AM
107owner
 
Join Date: Apr 2005
Posts: 7
Question 107 steering coupling

Hi. I'm new to this site and have learned alot from the experiences of others. Thanks for sharing your knowledge. My steering was loose so I replaced A drag link on my 1982 380sl. It was worn, but after I finished the steering was still loose. So had my son move the steering wheel while i was underneath(the car was jacked and blocked up 3 ways-still kind of scary)and I found my real problem was the steering coupling is very worn. My CD manual doesn't tell me how to replace this. It looks like you have to either remove the steering gearbox or the steering shaft to replace the coupling. Any advice would be helpful. BTW, I ordered the part on-line at www.*************** for $57.00 +free shipping for orders over $50.00. The dealer wanted $148.00 plus the gold fillings in my teeth. It pays to shop around.


Last edited by 107owner; 04-14-2005 at 11:10 AM.
Reply With Quote
  #2  
Old 04-14-2005, 01:56 PM
Registered User
 
Join Date: Mar 2003
Location: Convent Station, NJ
Posts: 755
Yup that's the order to R and R....damper, coupling then adjust or replace the gear box.

I'm interested to see how you do with the coupler. This is likely my nest project.
__________________
Rick

'85 380 SL (sold)
'85 Carrera Flatnose
'71 280 SL Signal Red/Cognac
Reply With Quote
  #3  
Old 04-15-2005, 11:38 AM
'81 380SL
 
Join Date: Mar 2005
Location: foot hills east of Redding CA
Posts: 20
replacing steering coupling

Yes it can be done ... but not for the faint of heart.
Just did my '81 380SL
First if it is a job you never want to do again ... this is one! pay the price for merc parts not after market!
Unbolt gearbox clamp ..coupling will slide up column a bit ... unbolt firewall boot under dash and slide up ..this will get you to top clamp bolt ...unbolt 3 15 mm bolts to gearbox ...this will let gearbox move a couple of in... coupling will now come off
when you put it back together have helper on the steering wheel for line up
spray paint gap in lower clamp to mark splines....top clamp can only be out 180 degrees
...but if you miss it turn signals won't auto turn off
good luck and have fun!h

Last edited by whunter; 04-25-2011 at 05:03 PM. Reason: Spelling
Reply With Quote
  #4  
Old 04-15-2005, 01:52 PM
107owner
 
Join Date: Apr 2005
Posts: 7
107 steering coupling

Too late to buy part from dealer.
My part from Arizona should arrive within a day but i will look at it and see if it looks beefy enough.
My understanding is that are no aftermarket couplings available, only OEM. We'll see.
I took a better look at the coupling from underneath the car and it looks like I can loosen the coupling bolts (2) which are set (Allen) screws.
Then I should be able remove gearbox bolts (3) from inside fender well and move gearbox enough to remove coupling.
The Pitman arm may have to be removed also.
I will evaluate that once I start.
The tip about spray painting the gap is a good one.
When I have completed the job I will chronicle my experiences on the forum.
Now I have to actually do the work!!
Thanks for the help.
Kraig

Last edited by whunter; 04-25-2011 at 05:05 PM. Reason: spelling
Reply With Quote
  #5  
Old 04-16-2005, 10:20 AM
'81 380SL
 
Join Date: Mar 2005
Location: foot hills east of Redding CA
Posts: 20
You won't have to remove the pitman arm (after this many years that can be an adventure to its own) The couplling will slide up the column a couple of in ... it will be stiff (colapsable) tap with punch.
my new coupling came with star instead of allen.
finding metric star to fit took as long as the job.
Reply With Quote
  #6  
Old 04-18-2005, 10:24 AM
Registered User
 
Join Date: Mar 2003
Location: Convent Station, NJ
Posts: 755
Kraig, If you haven't done this job yet please take some pics. Thanks.
__________________
Rick

'85 380 SL (sold)
'85 Carrera Flatnose
'71 280 SL Signal Red/Cognac
Reply With Quote
  #7  
Old 05-31-2005, 12:35 PM
Registered User
 
Join Date: Mar 2003
Location: Convent Station, NJ
Posts: 755
Anything to report?
__________________
Rick

'85 380 SL (sold)
'85 Carrera Flatnose
'71 280 SL Signal Red/Cognac
Reply With Quote
  #8  
Old 07-05-2005, 03:52 PM
Captain Scott's Avatar
Registered User
 
Join Date: Apr 2005
Location: Coos Bay Oregon
Posts: 90
Just about to Jump In

Quote:
Originally Posted by 107owner
Too late to buy part from dealer. My part from Arizona should arrive within a day but i will look at it and see if it looks beefy enough. My understanding is that are no aftermarket couplings available, only OEM. We'll see. I took a better look at the coupling from underneath the car and it looks like I can loosen the coupling bolts (2) which are set (allen) screws. Then I should be able remove gearbox bolts (3) from inside fender well and move gearbox enough to remove coupling. The Pitman arm may have to be removed also. I will evauate that once I start. The tip about spray painting the gap is a good one. When I have completed the job I will chronicle my experiences on the forum. Now I have to actually do the work!! Thanks for the help. Kraig
Hey Kraig,
I am about to move on replacing mine. How did it go??
Scott
'74 450SL with 221K
Reply With Quote
  #9  
Old 07-30-2005, 11:50 AM
Captain Scott's Avatar
Registered User
 
Join Date: Apr 2005
Location: Coos Bay Oregon
Posts: 90
Success

I am tight once again!

The main hiccup I found was in having to access the coupling bolts from the driver side inside the car, upside-down of course.
I had to take the boot off the firewall, slide it toward the steering wheel and then cut down an Allen wrench so it would fit thru the pass-thru.
Then it was simple.
Of course you need to mark BOTH shafts before you pull the old coupling.
Spray paint might work, but since you will want to spread the coupling to ease removal, you can just drive a slim chisel in to spread it and also mark the shafts.

Scott

Last edited by whunter; 04-25-2011 at 05:06 PM. Reason: spelling
Reply With Quote
  #10  
Old 08-25-2005, 10:57 AM
KATSCAN's Avatar
look to the cookie
 
Join Date: Aug 2005
Location: Pensacola/south carolina
Posts: 106
OK, I'm starting my coupler work now.
I can't seem to slide the firewall boot up the shaft.
removed column shaft screw also.
The boot won't move.
Everything tries to move with it as one piece.
What's the deal?
__________________
JHaburay

1972 280se 4.5 "princess"
1986 2.3-16v first 100 (099) USA

Last edited by whunter; 04-25-2011 at 05:07 PM. Reason: spelling
Reply With Quote
  #11  
Old 08-25-2005, 11:14 AM
Captain Scott's Avatar
Registered User
 
Join Date: Apr 2005
Location: Coos Bay Oregon
Posts: 90
Once the 4 screws that hold it to the firewall were out and the strap collar nut was loose, I had to pry a bit with a screwdriver between the metal "boot" and the firewall to get it moving and eventually, I grabbed it and twisted it up toward the steering wheel.
There was also a rubber gasket that was almost fused to the firewall.
Be careful, the edges of the metal boot are sharp.
Maybe a shot of nutzoff or WD-40 will get her moving.
Good luck.
You'll love the results!

Last edited by whunter; 04-25-2011 at 05:08 PM. Reason: spelling
Reply With Quote
  #12  
Old 08-25-2005, 12:35 PM
KATSCAN's Avatar
look to the cookie
 
Join Date: Aug 2005
Location: Pensacola/south carolina
Posts: 106
Well, I did get that off/loose from the firewall, it just needed to be twisted/rotated back and forth, and apparently, was doing that when you wrote.
I'm kinda po'd now cause my steering attachment of the coupler/ not the gear was near the end of the round tube....I couldn't get it to slide up.

Well, in fact I was following the thread and it said to loosen gear box side and it will slide two inches.

I'm not sure it can unless you loosen the steering side too, duh.
Well, since it didn't slide, I loosened the steering side. And proceeded to the gear box bolts.

Not even thinking to try to slide again.

Well, the gear box slides good but the coupling came off the steering wheel Hollow rod.

Now, You can't put it back around that rod so the steering column now must come off.

Not enough play now to get full slide and off).

Your's on the other hand (coupler) was slid up further to begin with because you couldn't get to the 2 nd Allen screw on the coupler.

I could get to both of mine from the engine compartment.

So anyone else that tackles this make sure you double check about the slide. Especially if you can unscrew your coupler (both nuts) from the engine compartment.

Just a "little" more work
__________________
JHaburay

1972 280se 4.5 "princess"
1986 2.3-16v first 100 (099) USA

Last edited by whunter; 04-25-2011 at 05:10 PM. Reason: spelling
Reply With Quote
  #13  
Old 08-25-2005, 02:02 PM
KATSCAN's Avatar
look to the cookie
 
Join Date: Aug 2005
Location: Pensacola/south carolina
Posts: 106
Did not have to take steering column out, etc.

I have a tendency to do almost exactly as it's written.

I usually do not take bolts all the way out in order to keep them with the part.

On this job make sure you take the coupling bolt all the way out from the steering half.

It will save you a lot of cursing, gojo, and at least one trip from confession.
__________________
JHaburay

1972 280se 4.5 "princess"
1986 2.3-16v first 100 (099) USA

Last edited by whunter; 04-25-2011 at 05:11 PM. Reason: spelling
Reply With Quote
  #14  
Old 08-25-2005, 07:10 PM
KATSCAN's Avatar
look to the cookie
 
Join Date: Aug 2005
Location: Pensacola/south carolina
Posts: 106
I'm having a ***** of a time putting the coupler on. I put the steering side on and can't get the box to get in all the way. Do I hammer or what?
__________________
JHaburay

1972 280se 4.5 "princess"
1986 2.3-16v first 100 (099) USA
Reply With Quote
  #15  
Old 08-25-2005, 08:06 PM
Super Moderator
 
Join Date: Apr 2000
Location: Falls Church, VA
Posts: 5,318
What on earth are you guys doing?

This is not a hard repair.

You remove the steering wheel and the combo switch, then the three screws in the steering hub that hold the steering shaft in.

You undo the coupling screws (a 1/4" hex bit ratchet and sockets really help) and pull the steering shaft up a couple of inches.

Install the new coupling, and reassemble in reverse order.

The only trick is to mark both ends of the steering shaft so you get everything to line up the way it was.

Otherwise you will have an off-center steering wheel and the turn signals will not cancel correctly.

Try a search - I did a detailed post on this when I replaced my steering box a year or two ago.

And it is on the CD.

I am not making this up.

__________________
Chuck Taylor
Falls Church VA
'66 200, '66 230SL, '96 SL500. Sold: '81 380SL, '86 300E, '72 250C, '95 C220, 3 '84 280SL's '90 420SEL, '72 280SE, '73 280C, '78 280SE, '70 280SL, '77 450SL, '85 380SL, '87 560SL, '85 380SL, '72 350SL, '96 S500 Coupe

Last edited by whunter; 04-25-2011 at 05:12 PM. Reason: spelling
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
126 frozen steering lock/tumbler removal (fairly easy, but long) jbaj007 Tech Help 4 09-21-2019 03:19 PM
107 Steering Coupler riske Tech Help 1 07-08-2005 04:57 PM
w115 Steering coupling Finished NC240D76 Vintage Mercedes Forum 3 11-22-2004 08:31 AM
Worth replacing a 123 steering coupling? surfblau Diesel Discussion 9 07-22-2002 12:26 PM
steering offset geometry bobbyv Mercedes-Benz Wheels & Tires 0 08-19-1999 09:20 PM



All times are GMT -4. The time now is 04:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page