Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Mercedes-Benz SL Discussion Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 12-09-2007, 03:28 PM
Registered User
 
Join Date: Jul 2002
Location: gray ga
Posts: 105
window motor

1979 450SL I belerve I need to replace left window motor - how do you re-mover and test . Jim
__________________
Jim
Reply With Quote
  #2  
Old 12-10-2007, 05:19 PM
Dan
 
Join Date: Oct 2007
Location: Tucson, Az.
Posts: 55
Mine is a 74 450 SL, if yours is the same then remove the door panel. You will see a terminal strip with two wires connected. Look for 12 volts there when the window switch is activated. Warning...what stops the window from going up too far or down too far is a mechanical stop, so power is still applied to the motor and it will continue to try to drive the window even though it has hit the mechanical limit. So clip your voltmeter to the terminal and only run the window long enough to see if the 12 volts is present. If present but no window movement, you need a new motor, or the wires from that terminal to the motor could be broken. If no 12 volts present then the switch is bad or wiring from the switch to the motor terminal block.

Look on the message boards for info on removing the door panel, there is quite a lot of help available...........Dan
Reply With Quote
  #3  
Old 12-10-2007, 07:55 PM
Registered User
 
Join Date: Mar 2003
Location: Milwaukee Wisconsin
Posts: 1,150
Geez....I hope you've checked the fuses first.
__________________
Resistance is Futile.
Reply With Quote
  #4  
Old 12-10-2007, 09:27 PM
Registered User
 
Join Date: Jul 2002
Location: gray ga
Posts: 105
79 450SL left windows works fine ,fuse ok, new switch.
I see two nuts holding motor- just remove nuts and push on old motor? Jim
__________________
Jim
Reply With Quote
  #5  
Old 12-11-2007, 08:58 PM
Engr693's Avatar
Registered User
 
Join Date: Apr 2006
Posts: 155
There are three screws holding the motor on. They have a 10mm head if I remember correctly. See the pic. This is from the passenger side. Still works if anyone is looking.
Attached Thumbnails
window motor-pass-window-motor-004.jpg  
__________________
Gary


1973 450SL
1999 Silverado 4X4 Ext Cab
1999 Mercury Sable
1972 450SL Parts car

Previously owned keepers:
1967 MGCGT - 3L-6
1972 Mustang Fastback - 351C

Current Cylinder Index: 37
Reply With Quote
  #6  
Old 03-08-2008, 05:31 PM
Registered User
 
Join Date: Jun 2007
Posts: 3
I just pulled my window motor out of the passenger side. I removed the nuts/bolts that secure the whole track mechanism to the inside of the door. 2 of the motor bolts can be removed from an access hole by moving the whole track to line the bolt with the access hole. The 3rd would not line up with the access hole so I used a small ratchet and 10mm socket. I took the motor housing off and saw that the plastic gear was stripped in one area which is why my window would stop moving up or down after a sec or 2.
Reply With Quote
  #7  
Old 03-08-2008, 05:32 PM
Registered User
 
Join Date: Jun 2007
Posts: 3
Forget to say I have a 1980 450SL
Reply With Quote
  #8  
Old 08-14-2008, 06:47 PM
Registered User
 
Join Date: Feb 2002
Location: queens,new york
Posts: 349
window motor

Would you please give a bit more detail as to hhow to get at the bolts holding the motor. I have a 1973 and I unbolted the X-Sissor mechanism and let it hang down and I still can't get to the bolts holding the motor. Thanks
Reply With Quote
  #9  
Old 08-14-2008, 09:05 PM
Engr693's Avatar
Registered User
 
Join Date: Apr 2006
Posts: 155
window motor removal

Here is one picture I took when removing the window motor from my '73 450SL. There are two bolts you can see, the other you need to get to from the back (inside)

engr693@yahoo.com
Attached Thumbnails
window motor-window-motor.jpg  
__________________
Gary


1973 450SL
1999 Silverado 4X4 Ext Cab
1999 Mercury Sable
1972 450SL Parts car

Previously owned keepers:
1967 MGCGT - 3L-6
1972 Mustang Fastback - 351C

Current Cylinder Index: 37

Last edited by Engr693; 08-14-2008 at 09:19 PM.
Reply With Quote
  #10  
Old 08-15-2008, 11:12 AM
Registered User
 
Join Date: Feb 2002
Location: queens,new york
Posts: 349
window motor

That is exactly the problem ,getting acess to the back and the third bolt holding the motor. Do I have to remove the forward channel and remove the glass from the door. HELPPPPPPPP!!!!!!!!!!
Reply With Quote
  #11  
Old 08-15-2008, 06:20 PM
Engr693's Avatar
Registered User
 
Join Date: Apr 2006
Posts: 155
window motor

No, the channel and the window do not need to be removed. You do have to remove the window regulator though in order to get your hands inside the door cavity. Once you remove the regulator, slide the window into the up position and block it in place. You can then reach in and feel for the last bolt and use the appropriate tools to remove it. I think I had to use a 1/4-inch drive ratchet or a 10mm wrench. This is all to the best of my recollection.
__________________
Gary


1973 450SL
1999 Silverado 4X4 Ext Cab
1999 Mercury Sable
1972 450SL Parts car

Previously owned keepers:
1967 MGCGT - 3L-6
1972 Mustang Fastback - 351C

Current Cylinder Index: 37
Reply With Quote
  #12  
Old 08-25-2008, 01:26 PM
Registered User
 
Join Date: Feb 2002
Location: queens,new york
Posts: 349
window motor

Thanks to all .The regulator finally came out with a lot of twisting and turning. I replaced the motor and reintaled the regulator. Now the problem is reinstalling the interior door panel. The weatherstripping is too tight for the window and pushes and strains the window glass. How do you attach the weatherstrip? On the panel before panel is placed on door or what? Thanks
Reply With Quote
  #13  
Old 08-25-2008, 11:04 PM
Engr693's Avatar
Registered User
 
Join Date: Apr 2006
Posts: 155
window adjustment needed

If your window is straining when you close it, it will need adjusting so it doesn't get overstressed. I think it is easier (or necessary) to make the adjustments with the door panel off. At the very least, the window stops need to be adjusted with the panel off. Be very careful tightening bolts, I inadvertently sent my passenger window crashing to the bottom of the door cavity in a bazillion pieces while tightening the "last" bolt.

Adjustments from what I understand are a bit tricky, just need a little finesse and patience. Good luck!
__________________
Gary


1973 450SL
1999 Silverado 4X4 Ext Cab
1999 Mercury Sable
1972 450SL Parts car

Previously owned keepers:
1967 MGCGT - 3L-6
1972 Mustang Fastback - 351C

Current Cylinder Index: 37
Reply With Quote
  #14  
Old 08-26-2008, 05:45 PM
Registered User
 
Join Date: Feb 2002
Location: queens,new york
Posts: 349
window motor

The window is not strained when I close it. The window strains against the weatherstripping when I bring the window up. There is virtually no room for the window and the weatherstripping. I am at a lost as to how to connect the weatherstrip clips, to the door or to the panel and then the combined panel with the strip to the door. thanks again.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 04:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page