Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Classified Ads > Mercedes-Benz Used Parts For Sale & Wanted

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-05-2007, 03:49 PM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
For Sale 107 4 speed manual trans.

Trans. is out of a 1973 Euro 350 slc. The trans. looks rebuilt. Clutch looks new. Comes complete with EVERYTHING needed to install from bell housing to rear end including complete brake/clutch pedal mount, drive shafts, floor shifter, and all nuts and bolts. Rear end number is 012505 3.46 SP. Rear end is a limited slip (sperrdifferential). I think the rear end is a higher ratio to match the trans. gearing and the drive shafts are different to accommodate the longer trans. Clutch master and slave cyls. obviously need kits in them.

The complete package is $1,200 plus shipping. All up I guess this weighs about 250 lbs. My zip is 78362 (just north of Corpus Christi, Tx.) so you can calculate the freight.

ps. The 350 engine is available free. l understand the cams will fit a 450 and add a bit of performance to it. The engine probably weighs about 400 lbs. or a bit less.

pps What ever is not sold by the end of Aug. is off to the junk yard. Make me an offer I can't refuse.

Last edited by kip Foss; 08-13-2007 at 06:01 PM.
Reply With Quote
  #2  
Old 08-05-2007, 07:30 PM
cth350's Avatar
Registered User
 
Join Date: Dec 2000
Location: Long Island, NY
Posts: 3,773
Is the engine in a usable state? I know a fellow that needs a 350. -CTH
Reply With Quote
  #3  
Old 08-06-2007, 07:51 AM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 34,420
That is a very desireable setup you are offering there, Kip. The v8 sticks are few and far between.

I am sure you will have no trouble selling it all.

I think you are a bit light on your weight estimates, maybe....especially the motor.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #4  
Old 08-06-2007, 08:46 PM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
Tom,

You may be right on the weight. My kitchen scale only goes up to 12 lbs. so unless I want to get real fancy with levers, etc. I an stuck estimating.
Reply With Quote
  #5  
Old 08-13-2007, 06:03 PM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
To bump this up I just found out that the diff. is a limited slip.
Reply With Quote
  #6  
Old 08-13-2007, 09:13 PM
diametricalbenz's Avatar
The Crowbar of Embriage
 
Join Date: Oct 2004
Location: Seattle, WA
Posts: 3,509
Are the driveshaft lengths the same as a 350/450SL?
__________________
1996 Dodge Ram 5.9L Cummins 12V 4(A) 4.10 - 163K - For Sale
1974 240D 3.0L 4(M) - 250K -OM617.910 + 300D FW + Rajay turbo power!
1977 6.9 3(A) - 84k
Reply With Quote
  #7  
Old 08-14-2007, 05:38 AM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
I don't think so since the sl is about 11" shorter than the slc. The rear shaft may be the same length but the front shaft may be longer. If you can send me the length of your drive shafts I can check the ones I have. I will be gone for 6 days to Oregon so I will get back to you on about the 20th.
Reply With Quote
  #8  
Old 08-14-2007, 07:50 AM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 34,420
On my 300cd stick conversion we had a new driveshaft fabricated since none that I had were long enough. Cost 175 locally. Looks like it grew there and works like a charm.

We are using the 307 diff too with no ill results, and the 240 flywheel is fine too. Very minor five cylinder vibrations at certain rpm.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
  #9  
Old 08-14-2007, 10:15 AM
cth350's Avatar
Registered User
 
Join Date: Dec 2000
Location: Long Island, NY
Posts: 3,773
A 450se engine I scrapped came in at like 575 pounds. The v8 automatic transmission is roughly 100 pounds. The standard should be about 75% of that going by size.

As for driveshafts. Getting a longer one cut down is straight forward and advisable, since it will be both rebuilt and well balanced (if done right) after so many years of use.

-CTH
Reply With Quote
  #10  
Old 08-19-2007, 10:46 PM
Registered User
 
Join Date: Jul 2002
Location: S. Texas
Posts: 1,237
Does anyone know if this trans. will fit on a 300 Diesel?
Reply With Quote
  #11  
Old 08-19-2007, 10:54 PM
t walgamuth's Avatar
dieselarchitect
 
Join Date: Apr 2005
Location: Lafayette Indiana
Posts: 34,420
I don't know why not, but I wouldn't sell it separately if I had it.

The stick setups that fit diesels are common. These v8 setups are rare as hen's teeth.

You will sell it eventually to someone who needs one for a v8.

Tom W
__________________
[SIGPIC] Diesel loving autocrossing grandpa Architect. 08 Dodge 3/4 ton with Cummins & six speed; I have had about 35 benzes. I have a 39 Studebaker Coupe Express pickup in which I have had installed a 617 turbo and a five speed manual.[SIGPIC]

..I also have a 427 Cobra replica with an aluminum chassis.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 01:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page