|
|
|
#1
|
|||
|
|||
ML 430 Gearshift stuck!!
I have an ML 430 year 2000. Recently the battery was dead and I had to charge it back up. When I started it the radio was not functioning so I took it out and completely unplugged it, put it back in and now it works fine. It started up yesterday just fine, began driving, and it won't shift out of first gear. Noticed the gear indicator by the clock was not registering anything - no PRNDL. I went back home in "limp home mode" and the gearshift was stuck in either neutral or park. When I turned off the key I could put it into park and remove the key.
The dealer told me to remove the trim around the gearshift and unplug some wires under the gearshift and plug them back in to reset it. (just like the radio). Anybody have any thoughts on this? I have it all torn apart awaiting your input..... |
#2
|
|||
|
|||
ON almost all 2000 & later Benzes w/auto trans the shifter is a computer...
That computer NEEDS the brake light circuit to function properly. We replace them all the time due to liquid spillage.... OF course a scanner is needed to "really" diagnose the problem..
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#3
|
|||
|
|||
brake light shifter - where is it?
thanks for the info - where is the brake light shifter? How would I know if it is really that?
|
#4
|
|||
|
|||
maybe battery?
Some one today told me it may just be the battery. The battery has been dead several times over the last couple of weeks. Could a weak battery cause all these issues?
I'm getting a new one tomorrow. Any thoughts???? |
#5
|
|||
|
|||
I asked the question "do the brake lights work".
Again that is the first requirement for the shifter to release! The battery should not have any effect.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#6
|
|||
|
|||
brake lights don't work!
Wow, the brake lights don't work. What is my next step? Can I replace this thing myself?
|
#7
|
|||
|
|||
The brake lamp switch is a common failure, VERY easy to install...MB number 001-545-64-09 with a $13 list price...
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#8
|
|||
|
|||
brake light switch
Thanks for the info. Where is it located? Under the dash? Under the hood? Any pictures or diagrams on the web you could direct me to?
|
#9
|
||||
|
||||
Quote:
See http://forums.mbnz.org/forums/forums/thread-view.asp?tid=1166641&posts=15 |
#10
|
|||
|
|||
Woo Hoo!
Thanks so much, can't wait to get this done and get back on the road.
|
#11
|
|||
|
|||
New Developments
Every day is a new beginning when you own an ML......
Today the brake lights are working fine. I realized that when I tested them yesterday the key was not on at the time. Now the key is stuck in the ignition. I can move the shifter from park to neutral, I can start the car (no problem with the battery - even though I went and bought a new one yesterday- I haven't installed it yet), I can put it into drive and go out on the street. The transmission will not go out of first. It seems it is still in "limp home mode". When I get back into the driveway I can't put it back into park unless I turn off the engine. Then it goes into park easily. But I can't get the key out!!! I am so doomed!!! Help please! |
#12
|
|||
|
|||
Quote:
A scanner that can read TRANS codes is needed!
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#13
|
|||
|
|||
Sometimes what looks like a major tragedy ends up being something simple and inexpensive. Take the advise from DOC and spend a few dollars to have the truck scanned before it nickle and dimes you to death. I imagine that battery wasn't cheap and may have cost you the difference to repair the truck. Believe me, DIYers need to have humility, or deep pockets.
__________________
Steve32 |
#14
|
|||
|
|||
Agreed. But please understand the last time I went to the dealer they wanted over $1000 to replace my power steering system and it turned out to be a $2 gasket. On another problem they wanted $600 for an EGR valve and it turned out to be an $80 CPS (which I fixed with your help!).
I just can't help but think it has something to do with the battery. And since the brake lights work fine with the key on and there has been no liquids spilled I can't believe it is the brake light switch since it releases out of park with no problem. The battery has to be jumped every day. Whatdya think??? |
#15
|
|||
|
|||
Ted, I was doing a search on symptoms of your problem. Did you have problems with the shift lock, in which you were sticking something into the unlock hole? I thought I saw your response in one of the posts, which may be a prelude to your problem, misaligned gear shifter contacts. Let me know what you think; this is what I found:
A strong possibility is the shift lever is out of adjustment. There is a feedback electronic circuit that tells the computer what gear you have selected. If the linkage has slipped, you can confuse the computer and throw it into the limp home mode. Put the trans in park and look to make sure the shift lever on the side of the trans is touching the metal stop bracket. If all is in proper adjustment, you will not a very smooth movement of the shift knob through all the gears with no hangups. If not, loosen the "torques" set screw on the shifter rod and move the shift arm over to the stop. I found it ½ way down the 1st page, post #10 of 99 ML320 Shifting Problem. Please Help
__________________
Steve32 |
Bookmarks |
|
|