|
|
|
|
|
#1
11-21-2002, 03:03 PM
|
|||
|
|||
|
supercharging 300E
Does anyone have any info. on supercharging for a 300E engine ? I would also be interested in turbocharging but prefer supercharging.
What about headers, intakes, injector upgrades, or computer chip upgrades ? Thanks Robert Davis
__________________
Robert Davis 
|
|
#2
11-21-2002, 05:43 PM
|
||||
|
||||
|
www.upsolute.com
 Do a search on yahoo for 300E turbo, I found a german site with a complete turbo kit ..
__________________
Brandon 2008 S550 1957 Dodge D100 1967 VW Microbus 21 Window 2001 Suburban 2004 Beach cruiser bicycle -----------------GO DUKE!----------------- "It cannot be emphasized too strongly or too often that this great nation was founded not by religionists, but by Christians; not on religion, but on the Gospel of Jesus Christ. For that reason alone, people of other faiths have been afforded freedom of worship here." Patrick Henry 1776
|
|
#3
11-23-2002, 01:57 AM
|
|||
|
|||
|
hehe, welcome to the board. Im sorry to say, but the 300E is pretty much a performance dead end. No big company makes headers or intakes for the m103 engined 300Es, injector upgrades aren't around, and the 103s engine manegment is too basic to benefit from a chip upgrade. Mosselman makes a bi-turbo kit for the benz, but it will run about 7k installed, and nets only about 265 hp. Turbo install on my 300E That is a link to a very informative thread on turbocharging your benz. So far, it seems that a td05 turbo is the best/cheapest way to add some ooomph to the car. I plan on installing one as soon as I can get enough vacation time. Good luck!
|
|
#4
11-23-2002, 05:57 AM
|
|||
|
|||
|
Turbo kits
Hopefully I will get a permanent shop soon. I can start making turbo kits for M102, M103 & M104 engines. seems to be quite a lot of interest. But I will make the kits DIY at first. I already have Turbo exhaust manifolds in the works for M102 & M103 engines.
Hopefully I will get them in soon. Cost is about $400 for the M102 and $525 for the M103 both made of Cast iron. Expect some news about April 2003.
__________________
WARNING: Bastard Mercedes Builder/Tuner Sorry if I don't answer your email or questions I don't check here too often. I am normally on the 190revolution.net board. Thanks
|
|
#5
12-12-2002, 04:20 PM
|
|||
|
|||
|
How much hp are you looking to produce out of this turbo and how much boost do you expect to run? I'm interested in buying the kit when you come out with it, how much?
|
|
#6
12-15-2002, 04:26 AM
|
|||
|
|||
|
In the beginning there will be no kit. I will just sell the exhaust manifold and some parts. Since the runs on the manifolds will be low in terms of quantity it may be about $500 to 600 for a Cast Iron manifold. It will accept the t3 turbine housing. It will also have a mounting flange for the turbonectics wastegate.
Basically you will have to do your own fabrication. This is the BASIC cost estimation: $2500 avg. Exhaust manifold: $600 Turbocharger: $750 Downpipe: $100 Intake Piping & couplers: $140 Intercooler: $200 to 400 (air-water $600) Air Flow meter adapter: $40-60 Fuel Enrichment: $175 Turbo Oil supply and drain: $80 individual results may vary.
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
