Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Search Forums

Showing results 1 to 30 of 500
Search took 0.08 seconds.
Search: Posts Made By: jeffsr
Forum: Tech Help 08-22-2003, 03:03 PM
Replies: 8
Views: 929
Posted By jeffsr
If it's the 86, check the third brake...

If it's the 86, check the third brake light(inside the rear window). A lot of folks tend to overlook that one.
Forum: Tech Help 08-15-2003, 10:03 PM
Replies: 1
Views: 684
Posted By jeffsr
You have high speed and low speed that are...

You have high speed and low speed that are selectable. Other speeds in between are slaved to the auto button (in between high and low) which is slaved to the temp setting wheel. Set it on auto and...
Forum: Tech Help 08-05-2003, 10:24 AM
Replies: 5
Views: 1,030
Posted By jeffsr
Put a minifold gauge on your system. Check high...

Put a minifold gauge on your system. Check high and low side pressures. You can cycle the compressor by disconnecting the low pressure cutoff switch on the receiver dryer.
Forum: Tech Help 08-04-2003, 06:07 PM
Replies: 4
Views: 718
Posted By jeffsr
It sounds like the flow control valve...

It sounds like the flow control valve (thermostat, if you will) for the washer resevoir has failed or is stuck open. You will have to remove the heater coil from the resevoir and test it. Simple to...
Forum: Tech Help 08-04-2003, 05:57 PM
Replies: 4
Views: 737
Posted By jeffsr
If you are seeing a white haze on the wood grain,...

If you are seeing a white haze on the wood grain, it is probably due to changes in the thick urethane coating on the wood. This will not polish out. Replace or have an experienced refinisher redo...
Forum: Tech Help 10-30-2002, 08:14 PM
Replies: 1
Views: 687
Posted By jeffsr
You will see coolant leakage from the weep hole...

You will see coolant leakage from the weep hole below the impeller shaft pulley, if the shaft seal is dying. If not, then check all the hoses, especially the short fellow between the pump and the...
Forum: Tech Help 08-23-2002, 07:33 AM
Replies: 12
Views: 1,242
Posted By jeffsr
Number of things to check. First, the fuse,...

Number of things to check. First, the fuse, located outside the fuse box forward of the firewall bulkhead, near the edge of the fender (on the driver's side) in a little black plastic holder...
Forum: Tech Help 08-01-2002, 11:23 AM
Replies: 12
Views: 1,262
Posted By jeffsr
Well??. Try a fluid and filter change...Also,...

Well??. Try a fluid and filter change...Also, have the operating pressures checked.
Forum: Tech Help 08-01-2002, 09:50 AM
Replies: 12
Views: 1,262
Posted By jeffsr
Have you had the control pressure cable properly...

Have you had the control pressure cable properly adjusted??
Forum: Tech Help 08-01-2002, 07:16 AM
Replies: 5
Views: 806
Posted By jeffsr
Steering damper. If you are going to explore...

Steering damper. If you are going to explore potholes frequently, you may need a different type of vehicle, i.e. HUM VEE or M1A1 Abrams. Both are up to the task. :D :D
Forum: Tech Help 08-01-2002, 07:13 AM
Replies: 7
Views: 26,476
Posted By jeffsr
You may be hearing the "singing gas cap" or you...

You may be hearing the "singing gas cap" or you have a leak in the tank system, that is "wheezing". Sniff around.
Forum: Tech Help 07-31-2002, 03:31 AM
Replies: 1
Views: 910
Posted By jeffsr
If you had a communication between the cooling...

If you had a communication between the cooling system and any of the cylinders, you would expect to see loss of coolant and high pressure in the cooling system. Remove the cap, start the engine and...
Forum: Tech Help 07-31-2002, 03:11 AM
Replies: 8
Views: 979
Posted By jeffsr
If you saw white smoke, I am wondering why you...

If you saw white smoke, I am wondering why you went right for the coolant buff up.:confused: :confused: :confused: Usually smoke associated with coolant leaks has a rather sweet odor (so to...
Forum: Tech Help 07-30-2002, 09:58 AM
Replies: 7
Views: 829
Posted By jeffsr
The mirror is mounted on a spring and ball...

The mirror is mounted on a spring and ball breakaway mount. You can remove it by grasping the stalk and pulling down. Replace is a bit more difficult, needs to be perfectly aligned with the grooves...
Forum: Tech Help 07-29-2002, 06:52 PM
Replies: 7
Views: 829
Posted By jeffsr
On the inside of the door, there is a small trim...

On the inside of the door, there is a small trim panel which pops off revealing 3 phillips head screws and the plug for the electrics. The little panel is right behind the mirror on the inside. ...
Forum: Tech Help 07-29-2002, 07:06 AM
Replies: 2
Views: 534
Posted By jeffsr
hydraulic

hydraulic
Forum: Tech Help 07-29-2002, 05:42 AM
Replies: 1
Views: 611
Posted By jeffsr
Sure, higher rating. But extra expense and not...

Sure, higher rating. But extra expense and not as flexible.
Forum: Tech Help 07-27-2002, 09:26 AM
Replies: 3
Views: 577
Posted By jeffsr
The yellow wire provides the control reference...

The yellow wire provides the control reference voltage from the ACC module. It should vary between 3 to 8 VDC (approximate). Red is system voltage. Black is reference ground for regulator as it is...
Forum: Tech Help 07-25-2002, 05:17 PM
Replies: 5
Views: 840
Posted By jeffsr
If you have the cash, go for it!! 13 plus...

If you have the cash, go for it!! 13 plus years on some of them. They're not getting any younger:D
Forum: Tech Help 07-25-2002, 05:14 PM
Replies: 11
Views: 1,044
Posted By jeffsr
Master cylinder

Master cylinder
Forum: Tech Help 07-25-2002, 03:20 PM
Replies: 3
Views: 1,095
Posted By jeffsr
The blower speed regulator modulates the blower...

The blower speed regulator modulates the blower speed by increasing or decreasing the resistance in the ground leg of the blower circuit. I.e., at low speed the ground leg is floating above zero,...
Forum: Tech Help 07-25-2002, 02:52 PM
Replies: 1
Views: 972
Posted By jeffsr
You should be hearing the fan clutch in before...

You should be hearing the fan clutch in before you get to 100 C (the mark between 80 and 120). Try this. Start the engine from cold. Rev it a few times to about 2000 rpm. Remember what that...
Forum: Tech Help 07-25-2002, 09:10 AM
Replies: 4
Views: 1,107
Posted By jeffsr
You are going to have to drill out the center of...

You are going to have to drill out the center of the lock cylinder. It will require a succession of carbide drills and a cooling spray. It is a messy job. If you are lucky, you will not destroy...
Forum: Tech Help 07-24-2002, 02:03 PM
Replies: 5
Views: 1,316
Posted By jeffsr
The cats are before the muffler and the...

The cats are before the muffler and the resonator. You are probably OK. The W124 exhaust systems usually have a deep mellow tone. The cats don't affect this unless they are blocked.
Forum: Tech Help 07-23-2002, 10:54 AM
Replies: 12
Views: 1,355
Posted By jeffsr
To rule out (or rule in) the speed sensor, engage...

To rule out (or rule in) the speed sensor, engage the system, set to max cool, pull the spade connectors off the binary pressure switch (on the receiver dryer), short the leads together (the wires,...
Forum: Tech Help 07-23-2002, 10:45 AM
Replies: 5
Views: 877
Posted By jeffsr
I would start looking for an exhaust leak. The...

I would start looking for an exhaust leak. The air intake for HVAC is at the base of the windshield. If you are getting fumes in the car, you should be able to find the leak with the hood open. ...
Forum: Tech Help 07-13-2002, 10:41 AM
Replies: 7
Views: 827
Posted By jeffsr
If you really want to get scientific, the SO...

If you really want to get scientific, the SO CALLED PRINCIPLE for this POS is alleged to be smoothing out induction air flow. Now, on the average automotive engine, w/o other related modifications...
Forum: Tech Help 07-11-2002, 08:49 AM
Replies: 6
Views: 759
Posted By jeffsr
The switch with the leads is for the fan. The...

The switch with the leads is for the fan. The other is for pressures.
Forum: Tech Help 07-10-2002, 08:15 AM
Replies: 6
Views: 759
Posted By jeffsr
You need to have the pressures checked. This...

You need to have the pressures checked. This will tell you where to start looking next. If pressures and charge are OK, I would bet on the binary cutout switch on the receiver/dryer.
Forum: Tech Help 07-10-2002, 08:08 AM
Replies: 18
Views: 1,641
Posted By jeffsr
You need to add more R whatever (12 or 134a) to...

You need to add more R whatever (12 or 134a) to you system. It is normal for high and low sides to be nearly equal after system has been off for a while and cool. If you are pulling negative...
Showing results 1 to 30 of 500

 
Forum Jump


All times are GMT -4. The time now is 03:56 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page