Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Search Forums

Showing results 1 to 10 of 10
Search took 0 seconds.
Search: Posts Made By: Jesper Bach
Forum: Tech Help 05-14-2006, 09:45 AM
Replies: 1
Views: 1,002
Posted By Jesper Bach
W123 280CE k-jet diag : What is "warm control pressure" ?

My trusty 280CE with, i beleive, a M110.888 engine has trouble idling, when the engine is warm. That is, when oil pressure drops below 1,0 (psi?). Idle is very rough, the warmer it gets...
Forum: Tech Help 09-01-2003, 04:28 AM
Replies: 1
Views: 964
Posted By Jesper Bach
Post Revisited : Valve ajd. problem, AVI movie.

Hi Forum,

Got no reply on the first post, which i can only take as one of two. So i chose to beleive that nobody'sever seen this before :-)

I put two small AVI's, showing the problem, on :
...
Forum: Tech Help 08-19-2003, 09:45 AM
Replies: 1
Views: 964
Posted By Jesper Bach
M110.98x valve adjust - something funny..

....is going on.

280CE '84 (European, no CAT) with 145000km's. Idle is rather rough, but accelerates and runs nicely on the highway. Not too much valve-clatter either. Uses no (zero :-) oil.
...
Forum: Tech Help 02-25-2003, 03:17 PM
Replies: 10
Views: 714
Posted By Jesper Bach
Actually it was not difficult at all, but i (felt...

Actually it was not difficult at all, but i (felt i) had the need to know if the pin was broken, so i took it out - it was not!

As luck have it, i have a 5mm mandrel i use for the brake pins, it...
Forum: Tech Help 02-25-2003, 03:05 PM
Replies: 10
Views: 714
Posted By Jesper Bach
The pin is back in place. I just need at test...

The pin is back in place. I just need at test drive or 2, but it is only 2 degrees Celcius tonight, so it will have to wait until tomorrow.

Let me stress one thing : DO NOT take the pin out! It...
Forum: Tech Help 02-25-2003, 12:00 PM
Replies: 10
Views: 714
Posted By Jesper Bach
I was on the phone with my locall MB guy this...

I was on the phone with my locall MB guy this morning and we came to about the same conclusion.

I wasn't sure if i did dare pull out the pin completely, because what if the guilde rail moves just...
Forum: Tech Help 02-25-2003, 02:55 AM
Replies: 10
Views: 714
Posted By Jesper Bach
Correction : actually Haynes calls this the...

Correction : actually Haynes calls this the "Intermediate gear guide".

Can it be changed with a new pin without risking the gear falls down and wrecks the intermediate gear :confused:

Jesper
Forum: Tech Help 02-24-2003, 03:02 PM
Replies: 10
Views: 714
Posted By Jesper Bach
Well, the good part is, the guide rail cannot...

Well, the good part is, the guide rail cannot have fallen down as the engine idles nicely, although i only dared let it run for 20 secs Sunday, as i was pretty sure this could be(come) serious....
Forum: Tech Help 02-24-2003, 01:36 PM
Replies: 10
Views: 714
Posted By Jesper Bach
So i'm not in for at major repair here :p ...

So i'm not in for at major repair here :p

The pin is not supposed to be locked to the slide rail by a locking-ring or so (internally) ?
If not, i take it, that the pin actually has a thread at...
Forum: Tech Help 02-24-2003, 11:37 AM
Replies: 10
Views: 714
Posted By Jesper Bach
W123 M110 : what does this part belong to ?

Just discovered a "dowel" protruding from the front right of the engine head.
There seems to be a "twin" just below it, firmly in place.

The dowel was halfway out, but I didn't dare pull it out...
Showing results 1 to 10 of 10

 
Forum Jump


All times are GMT -4. The time now is 11:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page