|
|
|
#1
|
|||
|
|||
W123 - License Plate Light lens/fixture repair...
Just in case you are not aware of them, there are a group of DIY articles available from MercedesShop.Com that will not show up in any SEARCH of the FORUM archives. Take a look at:
http://www.peachparts.com/Wikka Now to the subject of this POST and my " Wikka " DIY article that is available at: http://www.peachparts.com/Wikka/W123LicenseLights I know there are a lot of you DIYers who also have/use digital cameras so I want to encourage you to document your next DIY MBZ project pictorially and consider writing it up just as I did with this simple License Plate light lens repair project. Give back to the FORUM by adding to this GREAT DIY resource that is closely related via its sponsor MercedesShop.Com... and don't worry about grammatical correctness... let your pictures tell your project's story ! Enjoy, Last edited by Samuel M. Ross; 02-09-2007 at 10:35 AM. Reason: minor stuff ! |
#2
|
||||
|
||||
I like the cork gasket. I'll see if I can get around to making a few of those, they can be very informative.
__________________
-Zack K. http://www.maj.com/gallery/Boardmong...-Drive/si2.jpg 1983 300d Turbo (Daily Drive) -- 243,000 miles 1979 280ce AMG (Beginning extreme restoration) -- 141,410 miles 1979 Yamaha Chappy LB50 (Awating new points) -- 1411.6 miles 1981 300d Euro 4 speed -- 188,421 km -- SOLD 1979 300d Euro 4 speed (Sold to Brother) -- 257,000 miles A Collection of w123 AMG Cars and Parts |
#3
|
||||
|
||||
I was wondering where you could get that DIY cork gasket?
__________________
http://farm8.staticflickr.com/7271/7...144c3fc1dc.jpg |
#4
|
||||
|
||||
That is an elegant little repair Samuel. Some of the simplest repairs can be the most useful!
Thanks...
__________________
Jimmy L. '05 Acura TL 6MT 2001 ML430 My Spare Gone: '95 E300 188K "Batmobile" Texas Unfriendly Black '85 300TD 235K "The Wagon" Texas Friendly White '80 240D 154K "China" Scar engine installed '81 300TD 240K "Smash" '80 240D 230K "The Squash" '81 240D 293K"Scar" Rear ended harder than Elton John |
#5
|
|||
|
|||
excellent repair and write up... thanks!
|
#6
|
||||
|
||||
I pulled the 2 out of the parts car today, and besides having a little stain from rust of the wire/pins they are completely intact. They have some type of little sleeve that goes through the holes. I'll attach a pic in a minute or two....
__________________
Jimmy L. '05 Acura TL 6MT 2001 ML430 My Spare Gone: '95 E300 188K "Batmobile" Texas Unfriendly Black '85 300TD 235K "The Wagon" Texas Friendly White '80 240D 154K "China" Scar engine installed '81 300TD 240K "Smash" '80 240D 230K "The Squash" '81 240D 293K"Scar" Rear ended harder than Elton John |
#7
|
|||
|
|||
Lamp Housing Gasket
The lamp housing was removed to drain the water inside. When installed back, made the mistake of installing the left side of the holder to the right side causing the housing to break at the flange. The flange break was repaired with Locktite 408 instant bond adhesive and a splice made of the gasket material. Water got inside due to the deteriorated gasket.
Materials used were leftovers from previous projects. McMaster Carr: Gasket. 1/64” thick #9470K25 Locktite 408 #74765K51 |
Bookmarks |
|
|