Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes ShopForum > Technical Information and Support > SL Forum

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-28-2005, 01:52 AM
dmorrison's Avatar
Registered User
 
Join Date: Dec 2002
Location: Colleyville, Texas
Posts: 2,694
7 hours of work on the 560SL and not much done.

As the title says I put 7 hours of work on the SL today but not a lot got accomplished.

Sometimes while starting the car I hear a noise, I though was the starter solenoid not fully retracting. So got a rebuilt ( no new starters are available for the 107) starter from the dealer. Washed the car and the engine underside. Realized towards the end that I was baking in the sun. 100 here today. Put the car in the Garage and turned on the AC ( yes its Texas and I have an AC for my garage ). Jacked the car up and put it on jack stands and went inside to let the garage and myself cool off.
Inserted the oil extractor into the dipstick tube to change the oil. Figured I could let it suck away while I got the starter out.
The bottom bolt of the starter was pretty easy. Top top was a PITA. You must approach it from the rear of the bell housing. It is a 10MM Allen bolt head that treads into the starter flange. Got the Allen head inserted and then a 6 inch 3/8ths extension. A universal and then a, oops tranny panel is in the way. Remove the forward tranny panel and attached the 18 inch extension and gave it a yank. It would not budge. 125Ft. Lb. impact wrench, no go. 500Ft. Lb impact wrench. No go. When you use a universal aniline with the extensions it allows about 2 Ft. Lbs to transfer to the socket.
I tried and tried. Could not get it to release.
Called and talked to a tech at the dealer. They use a 3-4 ft long wobble 1/2 inch extension and then a 24 inch breaker bar. Do I have those, no. So I figured I would just let the dealer do it in my frustration. Of course I now know what I need and will get ti to try to get the job done.
Back to the oil change. Drop the filter and get the new one, Crap I don't have one. Usually have 1-2 on hand. Neighbor drives me to the dealer ( since the 300TD is apart waiting on the AC manifold hose to be rebuilt) and I get 2 filters. Talk to the mechanic that I trust and like. He gives me the poop on the starter. 10MM Allen head socket then a 6 inch 1/2" extension. A 1/2 inch 18-24 inch wobble extension with a 18-24 inch breaker bar. And really get into it. I may have to ask the neighbor if I can use is 4 post lift so I can " get into it". So tomorrow I have to get a 1/2 drive wobble extension.

While under the car lets look at everything I can see. A little play in the steering. Center drag link ball joint is bad, thats why I had one in the trunk for while now, replaced that. Thank God it went smoothly.
Checked all the front suspension and steering linkage. Great, I need Lower ball joints ( torn boots). 1 Upper control arm ( torn ball joint boot). So with this work I might as well rebuild the whole front end. I figure $1000 for parts. ( UCA are $364 each).
Steering box is leaking and I think the tranny front seal is developing a leak.

Well I've owned her since 1995 and she really has not cost a lot to run. So I now have a Fall project.

Did get the oil and filter changed but its now time to check the timing chain and rails.

So how was your day????????????????

Dave
__________________
1970 220D, owned 1980-1990
1980 240D, owned 1990-1992
1982 300TD, owned 1992-1993
1986 300SDL, owned 1993-2004
1999 E300, owned 1999-2003
1982 300TD, 213,880mi, owned since Nov 18, 1991- Aug 4, 2010 SOLD
1988 560SL, 100,000mi, owned since 1995
1965 Mustang Fastback Mileage Unknown(My sons)
1983 240D, 176,000mi (My daughers) owned since 2004
2007 Honda Accord EX-L I4 auto, the new daily driver
1985 300D 264,000mi Son's new daily driver.(sold)
2008 Hyundai Tiberon. Daughters new car

Last edited by dmorrison; 08-28-2005 at 12:28 PM.
Reply With Quote
  #2  
Old 08-28-2005, 11:45 PM
88Black560SL
 
Join Date: Oct 2004
Location: NC
Posts: 2,854
Quote:
Originally Posted by dmorrison
As the title says I put 7 hours of work on the SL today but not a lot got accomplished.

Steering box is leaking and I think the tranny front seal is developing a leak.


Dave
Be careful. I pulled my tranny thinking I had a front seal leak and it turned out to be a head gasket leak, dripping down behind the transmission.

John Roncallo
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 06:20 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2011 Pelican Parts - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page