|
|
|
#1
|
||||
|
||||
Rear Power Seat Removal
I recently found an '83 or '84 euro 500SEL with the rear power heated seat. I would like to adapt this system to my 300SDL, however I'm unsure how to remove the rear seat from the SEL? I plan to take the bottom and lower frames out and put my pads/covers on them then I'll also take the trim, wires, and switches from the 500. I figure that since I'll have the car there in the junkyard I can pull anything off that car to make it work and I've emailed back and forth with a member here who did the same thing so I'm pretty confident.
In the owner's manual it shows how to remove the rear seat but it has a note saying if it's the adjustable kind to take it to your authorized Mercedes-Benz dealer, yada, yada, yada, (you get the point). So, how is this seat removed? Just out of curiosity, are these cars already wired for the motors, etc.? so I can just drop everything in? I assume not, but I'll keep my fingers crossed. Thanks David
__________________
_____________________________________________ 2000 Honda Accord V6 137k miles 1972 300SEL 4.5 98k miles _____________________________________________ |
#2
|
|||
|
|||
I can't help with the seat removal, but as far as being pre-wired for optional goodies... I sure wish they would be. But unfortunately, they're not.
|
#3
|
||||
|
||||
bummer... Though I have to say I'm not surprised.
Thanks David
__________________
_____________________________________________ 2000 Honda Accord V6 137k miles 1972 300SEL 4.5 98k miles _____________________________________________ |
#4
|
|||
|
|||
MB specifies different seat covers for models with heated seats, so I'm not sure if you can use your existing skins with the heater pads. This sounds like a challenging project, but keep us posted!
|
#5
|
||||
|
||||
I would think I could adapt the heater pads to work with mine. When I've looked at seat covers I've never seen anything mentioned about heated. Really, I'd rather have the adjustable seat than the heated. Now I just need to find a way to heat the front ones as well. Perhaps I'll steal those from the 500SEL as well! My parents are going to love that one.
Thanks David
__________________
_____________________________________________ 2000 Honda Accord V6 137k miles 1972 300SEL 4.5 98k miles _____________________________________________ |
#6
|
|||
|
|||
The seat bottom is removed by removing 2 10mm bolts where the seat bottom meets the floor. Once the bolts are removed, you can just pull the seat forward (toward the engine) and out. There will be 2 plugs (for the seat heaters) to undo before you can pull the seat bottom out of the car.
I've never removed the seat back, so...no advice there. justin |
#7
|
||||
|
||||
I'll try that soon and get back with you all. Wierd, but I couldn't find anything outlining the procedure in the archives.
Thanks David
__________________
_____________________________________________ 2000 Honda Accord V6 137k miles 1972 300SEL 4.5 98k miles _____________________________________________ |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Power seat | piersbc | Tech Help | 8 | 05-23-2005 11:15 AM |
Swapping passenger seat for worn out driver's seat (power) on 300 SD | cmac2012 | Detailing and Interior | 0 | 04-17-2005 05:14 PM |
Installing power rear seat in 300SDL | LK1 | Tech Help | 0 | 09-07-2004 11:10 PM |
Bizarre problem with 560 SEL rear seat switches | rtoddholden | Tech Help | 3 | 11-27-2003 10:53 AM |
Audi Power Seat Question Help | Benz84 | Tech Help | 4 | 06-04-2003 10:20 PM |