Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 06-24-2006, 11:38 PM
Mark M's Avatar
1990 300te
 
Join Date: May 2006
Location: Orange Co, CA
Posts: 92
Do I need new rear shocks?

1990 300te
120,000 miles

Took it out today and I immediately noticed a bouncy-ness from the rear end with every little bump in the road. Stopped by Home Depot to pick up 3 large bags of topsoil and by the time I got home, the rear end on the driver's side was all the way down. Tried to bounce it by pushing down on the car, but it was bottomed out. Visual inspection and I don't see any fluid on the hydroponic shock and springs looked OK. Car has 120k miles and shocks are original. Accumulators were replaced about 3 months ago and leveling system was working fine up till today.

Do the shocks on this car help support the weight of the car at rest, or does the car sit only on the springs?

Do I need new shocks or should I be looking at somethings else? (I would hate to spend $800+ to find out that I should have replaced something else first).

Reply With Quote
  #2  
Old 06-24-2006, 11:47 PM
John Holmes III
Guest
 
Posts: n/a
You probably need the nitrogen spheres. There are one each for the left and right rear. When they go bad, the car will ride rough and low.
Reply With Quote
  #3  
Old 06-24-2006, 11:49 PM
John Holmes III
Guest
 
Posts: n/a
I meant to say that the replaced spheres could be defective(if they were rebuilt ones).
Reply With Quote
  #4  
Old 06-25-2006, 12:17 AM
Mark M's Avatar
1990 300te
 
Join Date: May 2006
Location: Orange Co, CA
Posts: 92
Accumulators were new, not rebuilt.
Reply With Quote
  #5  
Old 06-25-2006, 12:28 AM
John Holmes III
Guest
 
Posts: n/a
You could have a air bubble in the system due to a restricted filter/or low fluid. Steve Brotherton wrote a great post about getting a non operative system to work using no parts and a certain bleeding/priming procedure. I wish I could remember when he posted it.
Reply With Quote
  #6  
Old 06-25-2006, 02:16 AM
Mark M's Avatar
1990 300te
 
Join Date: May 2006
Location: Orange Co, CA
Posts: 92
If you know Steve's screen name, I can do a seach of his posts.
Reply With Quote
  #7  
Old 06-25-2006, 10:53 PM
John Holmes III
Guest
 
Posts: n/a
Glad to, his screen name is: "stevebfl". I think he is a moderator on the tech forum.
Reply With Quote
  #8  
Old 06-25-2006, 10:59 PM
John Holmes III
Guest
 
Posts: n/a
Just a random thought, but I wonder if the shop used the correct fluid? The incorrect fluid will sometimes cause the problems you are having.
Reply With Quote
  #9  
Old 06-26-2006, 03:52 PM
Mark M's Avatar
1990 300te
 
Join Date: May 2006
Location: Orange Co, CA
Posts: 92
I used the correct MB fluid when I flushed the system.

I ran a few more tests. I adjusted the rod. The hydraulic system operates fine lifting the car. The problem now is the driver side is 2.5 inches lower than the passenger side.

Time for new shocks or could the control valve be favoring one side over the other??
Reply With Quote
  #10  
Old 06-26-2006, 03:56 PM
davidmash's Avatar
Supercalifragilisticexpia
 
Join Date: Mar 2002
Location: Arlington, TX
Posts: 47,447
When my spheres went, the car road at normal hight but hard as a rock. Shook a few fillings worth so in my opinion, it does not sound like it is them. Did you loosen the lines going into the shocks to see if there is any pressure?
__________________
Sent from an agnostic abacus

2014 C250 21,XXX my new DD ** 2013 GLK 350 18,000 Wife's new DD**

- With out god, life is everything.
- God is an ever receding pocket of scientific ignorance that's getting smaller and smaller as time moves on..." Neil DeGrasse Tyson
- You can pray for me, I'll think for you.
- When you understand why you dismiss all the other possible gods, you will understand why I dismiss yours.
Reply With Quote
  #11  
Old 06-26-2006, 08:01 PM
Mark M's Avatar
1990 300te
 
Join Date: May 2006
Location: Orange Co, CA
Posts: 92
I have not loosened the lines going into the shocks. There should be sufficient pressure going into both shocks since when I move the control valve manually both sides of the car rise up. The only thing is that the driver side is lower.

I'm tempted to just replace both shocks since my car has 120,000 miles, but at $800 for the pair I have to take a gulp first. If this is what the control value does when it's failing, that would be an easier fix at about $300.

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 07:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page