|
|
|
#1
|
|||
|
|||
2002 C240 Tranny Problem!!!!!!!!!help
My car will not shift out of first gear, also it will not shift over where I can manually shift gears from drive with my slap stick gear shifter? When I shift out of part into reverse or drive it goes into gear violently. I am pretty handy and got a rebuilt transmission and installed it but the problem is still happening. Anyone have any idea what it could be?
|
#2
|
|||
|
|||
The shifter is most likely your problem. Did you get it wet right before the problem happened?
|
#3
|
|||
|
|||
your trans is in limp mode. codes need to be cleared or you may have a problem with module.
|
#4
|
||||
|
||||
Did you really replace the transmission without checking fault codes first???
I agree with above, it sounds like a bad shifter module.
__________________
1980 500SE/AMG Euro 1981 500SEL Euro 1982 380SEL 1983 300TD 1983 500SEC/AMG Euro 1984 500SEC 1984 300TD Euro 1986 190E 2.3-16 1986 190E 2.3 1987 300D 1997 C36 AMG 2003 C320T 4matic past: 1969 280SE 4.5 | 1978 240D | 1978 300D | 1981 300SD | 1981 300SD | 1982 300CD | 1983 300CD | 1983 300SD | 1983 380SEC | 1984 300D | 1984 300D | 1984 300TD | 1984 500SEL | 1984 300SD | 1985 300D | 1986 300E | 1986 560SEL | 1986 560SEL/Carat | 1987 560SEC | 1991 300D 2.5 | 2006 R350 |
#5
|
|||
|
|||
I had car checked for codes today by a friend and my car has a code in it P0702 transmission electrical system malfunction or something to that nature. Does that narrow it down for anyone out there? What kind of job is the shifter module that seems to be my problem from the feedback I am getting? Thanks alot.
|
#6
|
||||
|
||||
Before you waste any more money, check to see if the transmission control module is full of ATF.
|
#7
|
|||
|
|||
I have replaced the transmission control module.
|
#8
|
|||
|
|||
I replaced the transmission because when I pulled the pan off there was lots of shavings in the pan. Do I need to have the computer reset now? Does the code stay in the system, could I have fixed the problem and the code still be in the car's computer?
|
#9
|
||||
|
||||
yes, reset the codes and reset shift adaptations as well.
__________________
1980 500SE/AMG Euro 1981 500SEL Euro 1982 380SEL 1983 300TD 1983 500SEC/AMG Euro 1984 500SEC 1984 300TD Euro 1986 190E 2.3-16 1986 190E 2.3 1987 300D 1997 C36 AMG 2003 C320T 4matic past: 1969 280SE 4.5 | 1978 240D | 1978 300D | 1981 300SD | 1981 300SD | 1982 300CD | 1983 300CD | 1983 300SD | 1983 380SEC | 1984 300D | 1984 300D | 1984 300TD | 1984 500SEL | 1984 300SD | 1985 300D | 1986 300E | 1986 560SEL | 1986 560SEL/Carat | 1987 560SEC | 1991 300D 2.5 | 2006 R350 |
#10
|
||||
|
||||
Did you buy a new coded TCM for your vehicle and transmission, used TCM will not work unless coded.
__________________
Steve Cattaneo www.mastertechtrans.com 03 SL500 02 MB AMG 87 560 SEC 87 300D 928S 83 85 928 S2 EURO |
#11
|
||||
|
||||
Did you flush the transmission cooler? If there were metal shavings in the pan, you can be sure there's some in the cooler as well.
|
#12
|
||||
|
||||
same goes for the torque converter- was it replaced?
__________________
1980 500SE/AMG Euro 1981 500SEL Euro 1982 380SEL 1983 300TD 1983 500SEC/AMG Euro 1984 500SEC 1984 300TD Euro 1986 190E 2.3-16 1986 190E 2.3 1987 300D 1997 C36 AMG 2003 C320T 4matic past: 1969 280SE 4.5 | 1978 240D | 1978 300D | 1981 300SD | 1981 300SD | 1982 300CD | 1983 300CD | 1983 300SD | 1983 380SEC | 1984 300D | 1984 300D | 1984 300TD | 1984 500SEL | 1984 300SD | 1985 300D | 1986 300E | 1986 560SEL | 1986 560SEL/Carat | 1987 560SEC | 1991 300D 2.5 | 2006 R350 |
Bookmarks |
|
|