|
|
|
#1
|
|||
|
|||
Clutch pedal doesnt spring back, even seems to go in by itself
1983 240D My clutch pedal won't release sometimes when I shift. Sometimes it even seems to press itself in. Obviously this isn't safe in busy traffic or the highway. I tried making the two adjustments, one on the lobed screw on the clutch pedal and the other on the spring.
I have a strange guess--is this due to a sticking throw out bearing? The slave cylinder and the attached components were replaced brand new 2 years ago. |
#2
|
|||
|
|||
Check the clutch master cylinder. I just replaced mine at 275k and it was leaking like a sieve upon closer examination. Mine was exceptionally bad on cold mornings. By the way, are you having to add brake fluid to your reservoir??
__________________
'06 E320 CDI 51K miles '02 VW Jetta GLS TDi 120k miles '99 Ford E350 7.3L Powerstroke 200k miles -sold '84 Euro 300D 5 spd manual 317k miles - sold |
#3
|
|||
|
|||
clutch cylinder
Its fine. I also bled the slave cylinder. I also use a hand pump oiler to pump fluid into the cylinder through the bleed screw. I'm thinking this must be somewhere else.
Well anyway, I'm going to by a huge spring and jury rig it to yank the clutch pedal back no matter what until I figure this out. I tied a piece of rope to the pedal so in an emergency situation, I yank on the rope to bring the clutch pedal back. Obviously thats not Mercedes-type engineering! This is really wierd. All of a sudden the clutch pedal will freezin place or even get retracted like an invisible foot is stepping on it. |
#4
|
||||
|
||||
Just because the slave cylinder was replaced two years ago doesn't mean the slave hasn't gone bad, just less likely it has. Did you simply look at the return spring or did you check it to see if it hasn't weakened/stretched? Is there a zerk at the clutch fork pivot point, possible that that lever may be binding/sticking. Also possible that the hydraulic line to the slave has begun to break down like an old rubber brake line (if the supply line is rubber), the interior could collapse which would restrict the return flow of hydraulic fluid. Also check the pedal pivot point up under the dash, make sure it is moving freely.
Check out all the easy to get to things before jumping to dropping the tranny. I've driven manny trannies for many, many years, and have never had a throw out bearing stick and cause what you describe.
__________________
Mike Tangas '73 280SEL 4.5 (9/72)- RIP Only 8,173 units built from 5/71 thru 11/72 '02 CLK320 Cabriolet - wifey's mid-life crisis 2012 VW Jetta Sportwagon TDI...at least its a diesel Non illegitemae carborundum. Last edited by MikeTangas; 10-17-2001 at 01:38 PM. |
#5
|
|||
|
|||
My vote is for the hose
I've had two hydrolic hoses clog and cause problems. The rubber came out of the crimp. Had a local hydrolic shop make a hose for less than OEM.
The throw up, I mean throw out bearing wouldn't cause any clutch pedal problems, it would keep the clutch spinning. I'm always suspisious of new parts cause of infant mortality, although two years would make that toddler mortality.
__________________
5 speed '91 190E 2.6 320,000 mi. (new car, fast, smooth as silk six, couldn't find any more Peugeots) 5 speed '85 Peugeot 505 2.5l Turbo Diesel 266,000 mi. (old car, fast for a diesel, had 2 others) 5 speed '01 Jetta V6 (new wifes car, pretty quick) 5 speed '85 Peugeot 505 2.2l Turbo Gas 197,000 mi. (wifes car, faster, sadly gone just short of 200k ) 5 speed '83 Yamaha 750 Maxim 14,000 mi. (fastest) 0 speed 4' x 8' 1800 lb Harbor Freight utility trailer (only as fast as what's pulling it) |
#6
|
|||
|
|||
Put a rebuild kit in the master cylinder and that will fix your problem. You must also hone the bore of the master cylinder.
P E H |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Final chapter for 190E clutch saga (I hope) | Greg in Oz | Tech Help | 8 | 12-13-2012 12:10 PM |
180E Clutch: Low Pedal Engagement | cowiepeters | Tech Help | 9 | 12-03-2003 07:30 PM |
"High" clutch pedal problem. Any ideas? | Greg in Oz | Tech Help | 19 | 07-07-2003 02:14 AM |
Brakes | rdc5000 | Diesel Discussion | 12 | 09-28-2002 07:30 PM |
Clutch: How do I stuff the Slave Cylinder back in? | Cinnaman | Tech Help | 1 | 10-19-1999 08:14 PM |