Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 10-15-2009, 10:38 PM
Registered User
 
Join Date: Feb 2009
Posts: 35
No heat in my 87 300E

Gotta 87 300E, running great otherwise.
Just recently it started to flicker with the heat starting up. It would flicker and intermittently turn on and sometimes stay off.
Just recently the pattern has been that the heat won't turn on until the engine has reached fully warm and stayed there for a couple minutes for the heat initiates. It usually would kick in once the engine temp sensor came up off 40.
Is it the monovalve?
I'm anticipating a bad temp sensore somewhere?
I was thinking a short but it doesn't flicker anymore...
Fuses are all new and working.
Any suggestions are greatly appreciated.
Thanks guys.
Cam

__________________
1987 300e W124 M103 My baby.
Reply With Quote
  #2  
Old 10-16-2009, 01:46 PM
junqueyardjim's Avatar
Registered User
 
Join Date: Apr 2005
Location: Cicero, Hamilton County, Indiana about 30 miles north of downtown Indianapolis
Posts: 2,623
Can you make your post clear?

What "flickers"?
__________________
Junqueyardjim
Christianity, if false, is of no importance, and if true, of infinite importance. The only thing it cannot be is moderately important. C.S. Lewis



1983 Mercedes W123 240D 4 Speed 285,000 on the road with a 617 turbo, beautiful butter yellow, license plate # 83 240D INDIANA

2003 Jaguar Type X, AWD. beautiful, good mileage,
Mom's car, but I won't let her drive it!
Reply With Quote
  #3  
Old 10-16-2009, 07:09 PM
Registered User
 
Join Date: Sep 2009
Location: Great State of Texas
Posts: 440
Just a guess, but doesnt the car get its heat from the engine? On almost 99.9% of vehicles (including new cars), the heat comes from hot coolant going through a heat exchanger in the air distribution system, and coolant doesn't start moving until the thermostat opens up...

Some cars do have electric heat (I'm just learning about MB's), but you probably won't get heat until your engine is up to temp.

If you have auto climate control, you might try running the wheel up & down a few times to clean the contacts.

I'd also like to know what's "flickering". If the engine isn't up to temp, the climate control system might be turning on & off until it starts getting hot air...
__________________
A.S.E Tech A1,A6,A7,A8 & MVAC 609 + EPA 608

Unless stated otherwise, any question I ask is about my greymarket 1985 380SEL.
Reply With Quote
  #4  
Old 10-17-2009, 02:42 AM
Registered User
 
Join Date: Feb 2009
Posts: 35
Correct.
By "flickering" I meant that when the engine is cold and starts to warm up, the blower will turn on and off in rapid sequence like there's a short when the cabin heat is engaged. Just recently, the blower won't kick in until the engine has been at optimal operating temp for some time. It used to kick in when the coolant first circulated through the air distribution system. I know the coolant is coming through because I can feel it radiating (minimally) with my hand up against the vent. It just takes a bit for the blower to start circulating air over it and out the vents.
I'm wondering if I have a bad temp sensor somewhere...
I've tried the rolling of the wheel, and tried other functions. None work until the engine reaches a minimum of 40 degrees.
Thanks for the input!
Cam
__________________
1987 300e W124 M103 My baby.
Reply With Quote
  #5  
Old 10-18-2009, 11:51 PM
Registered User
 
Join Date: Oct 2009
Posts: 6
heater

check the fuse in the engine compartment for the blower motor. this fuse will fail and can be split even though it looks good. take a small screwdriver and see if it will seperate. if it does then replace it. i believe it is a bi metal 30 amp fuse. very cheap to replace. if it is ok also wiggle the ignition switch. sometimes these will fail and cause something similar. hope this helps
Reply With Quote
  #6  
Old 10-23-2009, 10:37 PM
Registered User
 
Join Date: Feb 2009
Posts: 35
Already had replaced the fuse and the tumbler was replaced in the ignition about two months ago...
Still having the problem.
I appreciate your input. Any other ideas?
Cam

__________________
1987 300e W124 M103 My baby.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 06:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page