Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes ShopForum > Technical Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 12-13-2001, 12:59 PM
Registered User
 
Join Date: Oct 2001
Posts: 226
CD Changer Install

I am going to be installing an Alpine 6-cd changer to a 1994 C280. I was told the prewire went to the right rear in the trunk. Anybody know where exactly this wire is and how far I have to pull away the paneling? Do I need to remove the paneling or just pull it aside? Thanks.
Reply With Quote
  #2  
Old 12-13-2001, 02:16 PM
islandsound
Guest
 
Posts: n/a
The MBZ pre-wired harness should be located around the fenderwell, usually tied down w/ cloth tape or wire tie. To interface an Alpine M-Bus CD-Changer w/ the MBZ, you will need a logic controller adapter. Best one around is made by Blitzsafe (www.blitzsafe.com), available via your local car audio shop. After plugging in the adapter cable, route it under side compartment and mount the CDC in vertical position, flushed to body frame. Don't forget to reset the Alpine suspension springs to vertical mount before installation. Good luck and happy holidays.

Hank Nguyen
Reply With Quote
  #3  
Old 12-13-2001, 02:22 PM
Registered User
 
Join Date: Oct 2001
Posts: 226
Thanks and Happy Holidays to you, too. The CD changer is going to be a gift for my mom.
Reply With Quote
  #4  
Old 12-13-2001, 08:24 PM
Registered User
 
Join Date: Jun 2001
Location: California
Posts: 324
On my '94 E320 it's on the passenger side. Probably the same for yours.
__________________
D.H.

04 ML500
02 E430

Experience is something you don't get until just after you need it.
Reply With Quote
  #5  
Old 12-14-2001, 01:58 AM
cf cf is offline
Registered User
 
Join Date: Aug 2000
Posts: 51
If you want to do a clean installation, spend the money on the OE mounting plate which bolts onto pre-drilled holes on rear right steel member. This saves you from having to drill holes on the inside bottom to mount the CD changer.

The CD player may or may not fit on this MB tmount. Ask the car audio shop to drill/rivet the 2 metal brackets for holding the changer onto the mounting plate.

At least that's how I installed mine.

C.F.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
560SEL CD changer install Aaron Car Audio and Multimedia 3 04-04-2005 08:41 PM
How to install CD Changer in W209 step by step bryanm Car Audio and Multimedia 1 12-22-2004 10:47 AM
How to install CD Changer in W209 step by step bryanm Tech Help 2 12-22-2004 10:43 AM
CD Changer Install for C230 Kompressor mattd Car Audio and Multimedia 1 09-15-2004 11:24 PM
Repost! Alpine changer install in R129 Smalk Car Audio and Multimedia 6 04-23-2002 10:40 PM



All times are GMT -4. The time now is 09:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2011 Pelican Parts - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page