Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-06-2010, 06:15 PM
klaus kallas's Avatar
Registered User
 
Join Date: Jan 2001
Location: Clayton, NC
Posts: 491
1999 E320 4matic front axle shafts....

...can anyone point me to a DIY link? Searched but no luck. If no one has made one, I will jump into the thing and try to take some pics along the way, but would like some guidance !!

Saw some info that you just disconnect the tie rod and sway bar and swing the whole steering knuckle assembly out of the way. Does this sound correct?

Thanks!

Klaus

__________________
‘84 300TD “Mountain Goat”
'62 300d Adenauer-350 Chevy - "Max"
'15 VW Passat TDI
'16 Dodge Ram 3500 - Cummins w/6-speed
'68 Mustang fastback
'55 T-bird
‘63 Studebaker Hawk
Reply With Quote
  #2  
Old 07-28-2010, 04:15 PM
klaus kallas's Avatar
Registered User
 
Join Date: Jan 2001
Location: Clayton, NC
Posts: 491
Got this job taken care of a few weeks ago with the help of crashone (Thanks man!). Fired up the WIS program to check out the job and it wanted us to take apart the whole front suspension, engine, and the rear window wiper if I recall correctly.....

Here is the job in a much more shade tree friendly format:

1. Unbolt front axle nuts through the center of the hub using a 30mm socket OR jack up car and remove wheels, and have a friend hold the brakes tightly while you break them loose.

2. Once car is in the air and axle bolts and tires are off, proceed to remove the two bolts from the bottom of the sway bar at the lower control arm.

3. Next, unbolt the tie rod and smack it loose with a hammer and block of wood (as not to damage the bolt and threads) or use a puller if you are really fancy.

4. Unbolt the lower ball joint to spindle bolt and repeat above procedure.

5. Pull axle out of the back of the spindle and swing spindle out of the way (tie with wire or a bungee cord).

6. Unbolt the lower shock to control arm connection. Put a jack under the control arm to help give a little lift to the arm which will make driving the bolt out a bit easier. The shock/spring are not going to jump out at you, it is retained by the spring mount and is not under pressure when at its farthest travel.

7. Probably the hardest part of the job - pry the sway bar back and over the top of the control arm to allow a gap to open between the control arm and the shock. Hard to explain, but you will see once you get to this point why it is necessary.

8. Pry the axle out at the front differential while a friend supports/pulls the other end. It is retained by a snap ring and will just pop out.

9. Slip the thinnest part of the axle between the shock and the control arm and taa-daa! there you have one greasy, limp, and utterly useless halfshaft with which to play croquet, softball, or use for a paperweight. Below is a picture of the suspension at this point. Lower ball joint happened to be swung backwards, so trust me the connection is there, just not visible.

10. Spray a little white lithium grease on the ends of the new shaft to ease installation. Position shaft in differential, and while keeping slack out of the joints, pop it in gently with a rubber hammer.

The remainder is the reverse of the removal. Don't worry about getting the two axle sides confused, one is male and the other female at the differential. Also, I bought mine from a supplier in Connecticut for $95 a piece, and while the shafts themselves looked great, the new axle nut is too big to use. Get a new pair from Mercedes as well as some new lock nuts (4) for the tie rods and ball joint.

Whole job took us about 3 hours total for both sides with a break for lunch, so don't get frightened by the OEM procedure.

Good luck!!

Klaus
Attached Thumbnails
1999 E320 4matic front axle shafts....-w210-axle-2.jpg  

__________________
‘84 300TD “Mountain Goat”
'62 300d Adenauer-350 Chevy - "Max"
'15 VW Passat TDI
'16 Dodge Ram 3500 - Cummins w/6-speed
'68 Mustang fastback
'55 T-bird
‘63 Studebaker Hawk
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 03:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page