|
|
|
#1
|
|||
|
|||
Heater Core ByPass - 190e 2.6
I'm still drying my pants from the coolant leak....the heater core finally gave out and I need to know what is the correct procedure to bypass the core until I have the time to fix it (I heard the dash needs to come out, yikes!).
Does anyone have the correct parts list that I need to purchase to make this work? Do I connect the coolant hose before the vacuum control valve or after it? Can i just remove it all together? Then, the other side of the hose right into the block? Any assistance is greatly appreciated!
__________________
--------------------- 200 75 W115 (Mom's) 190e 90 2.6 W201 E320 95 Wagon W124 72 BMW 3.0 CSI |
#2
|
||||
|
||||
I would guess you must reroute it after the monovalve because otherwise the CCU will keep opening/closing the valve inside which if not submerged, may prematurely fail or even possibly be a fire risk.
And basically everything has to come out to do it. Do the evaporator at the same time and all vacuum pods. Not a job you want to do twice.
__________________
2016 Monsoon Gray Audi Allroad - 21k 2008 Black Mercedes E350 4Matic Sport - 131k 2014 Jeep Wranger Unlimited Sahara - 62k 2003 Gray Mercedes ML350 - 122k |
#3
|
|||
|
|||
Just finished the bypass on the car - definitely a DIY job until I can replace the heater core inside the dash, and everything else. I hope it holds.....items I purchased:
(1) 3/4" Heater Hose - 3ft. (2) 2 Universal 3/4" 90 degree elbow adapters (3) Clamps I went ahead and routed the hose from the heater valve, behind the firewall, and to the driver side hose. Worked well so far, no heat - but that's expected.
__________________
--------------------- 200 75 W115 (Mom's) 190e 90 2.6 W201 E320 95 Wagon W124 72 BMW 3.0 CSI |
#4
|
||||
|
||||
I had the same thing happen to me on my 190E as well. I bypassed my heater core for about a year or so and finally replaced it this past december. It wasn't as bad as I thought. Here is a quick list of things that you will have access to that you may want to replace (all are optional):
1) two vacuum pods 2) brittle, plastic vacuum lines + rubber connectors 3) replace/repair switchover valve (mine was britle where the connectors were and 2 of them broke off so I replaced it) 4) instrument cluster lights (and while you have the cluster out, if you want to do anything with it, now would be the time, i.e., replace fuse, change dial, repaint needles, etc.) 5) clean up vents/ducts 6) replace evaporator 7) replace lights inside ash tray and climate control 8) replace/repair blower speed switch (if you have the one that slides, there is a plastic piece that breaks inside the unit that will prevent the switch from sliding to the desired speed) 9) check ignition (sometimes the 190s key won't turn in the ignition, not sure what causes it) 10) speaker/radio upgrade 11) throoughly clean the dash while you have it off with some cleaner and condition it with some Lexol leather conditioner. 12) Also, may as well flush your cooling system too since you'll need to drain it again. Again all of these things are optional, but hey, if you have the time and are able to get some of the replacement parts, you might as well go for it. As na side note, when my heater core exploded on me I'm lucky I wasn't driving, I barely turned on my car and it gushed out all over my leg and the driver side floor....because I like to make sure things are extra secure/protected, what I did to my new heater when I got it was put an extra seal of clear water epoxy that can withstand 1500 psi around the edges where the aluminum meets the plastic and I also put a coat around the plastic part where you connect the aluminum pipes. I wanted to put a sleeve over the aluminum pipe all the way up to the plastic part so if it did leak again he the coolant would drain out of the car.....a sleeve would not fit though:-( just my 2 cents. Good luck.
__________________
1990 190E 3.0L Last edited by lsmalley; 03-31-2013 at 03:33 AM. |
Bookmarks |
|
|