|
|
|
#1
|
|||
|
|||
Stubborn Rear Brake Rotors o n 300E
1986 300E,
Having replaced my front pads and rotors recently, I went after the rears today. The calipers are off, retaining bolts removed, parking brakes adjusted all the way "in," but the rotors will not budge. I have sprayed penetrating oil on the hub, and given both sides a pretty good whack with a hammer - no luck. Are pullers ever used to get these rotors off? TIA
__________________
Chuck Taylor Falls Church VA '66 200, '66 230SL, '96 SL500. Sold: '81 380SL, '86 300E, '72 250C, '95 C220, 3 '84 280SL's '90 420SEL, '72 280SE, '73 280C, '78 280SE, '70 280SL, '77 450SL, '85 380SL, '87 560SL, '85 380SL, '72 350SL, '96 S500 Coupe |
#2
|
|||
|
|||
time ...
I had similar trouble in removing the rear rotors. After confirming that the parking brake was disengaged and the rotor spinning freely after adjusting the brakes all the way in, I dripped some engine oil on each wheel stud as well as the opening where the small allan screw that holds the rotor to the hub came out of.
I slowly rotated the rotor allowing oil to seep in. Whilst turning I tapped the rotor with a mallet and a piece of wood (too scared to damag the rotor with a metal to mettal banging). This eventually freed the rotor. Keep banging and turning the rotor. With a soft surface protecting the rotor you need to bash quite forcefully - it's the shock created that will free the rotor. happy banging L |
#3
|
|||
|
|||
u da man, Louis.
I sprayed penetrating oil as you suggested and let everything sit overnight. Gave the rotors some good whacks with a mallet, turning about 90% between whacks. After 5-6 good blows, both came off. There was a fair amount of rust between the flanges and the rotors, and around the hub. Look me up if you come to DC and I'll buy you a beer!
__________________
Chuck Taylor Falls Church VA '66 200, '66 230SL, '96 SL500. Sold: '81 380SL, '86 300E, '72 250C, '95 C220, 3 '84 280SL's '90 420SEL, '72 280SE, '73 280C, '78 280SE, '70 280SL, '77 450SL, '85 380SL, '87 560SL, '85 380SL, '72 350SL, '96 S500 Coupe |
#4
|
|||
|
|||
glad i could help !!
question that now comes to mind:
how do the pro's get the darn thing off without waiting 8 hours for the oil to to their thing .. |
#5
|
|||
|
|||
They beat it useless to get it off and tell you that the rotor is bad.
|
#6
|
|||
|
|||
use the puller
1. I use a puller myself see this post : Rear brake disc removal
2. Did the hammer thing years ago and stop because I’m now wiser, things could get damage around there… Thai GI sends…
__________________
GI but not GI Joe They call me "The Thai GI" Thai in the US Arsenal |
#7
|
|||
|
|||
I use a sledgehammer with a curbweight of at least 2kg and give the disc a few good whacks on the "drum" part while applying pressure with my prybar between the disc and something sturdy behind it.
Haven't failed me yet.
__________________
/Per MB E300TDT -98 |
#8
|
|||
|
|||
I use a sledgehammer with a curbweight of at least 2kg and give the disc a few good whacks on the "drum" part while applying pressure with my prybar between the disc and something sturdy behind it.
Haven't failed me yet.
__________________
/Per MB E300TDT -98 |
#9
|
||||
|
||||
A (very) light coating of anti-seize paste (or any heavy grease) applied to the mating surface can prevent this problem in the future. Not too much- you do not want the grease to get on the braking surfaces.
Of course, sometimes it is the parking-brake shoes that are holding things up, especially if they have dug themselves a ridge to grab on. |
Bookmarks |
|
|