Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 05-11-2019, 03:43 PM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
95 e320 codes

pin 8: 25,33,38 pin 14: 4

seems intermitting. will drive perfect one day then the next not so much. when the cel comes on itll have a hiccop or weak miss. runs beautiful when cold. not too sure why theres a cc code. must have been somehting i did when i did the head gasket. cc has been working.

updated harness, new timing chaing and head gasket, new cam sensor, o2 sensor, variable cam sensor, maf sensor, updated throttle actuator..and yes when i put the timing in i rotated the variable cam clockwise.
i have fresh sensors and the readings at the connectors match up with the readings on my other w124 which runs beautiful. came on here to get help with theh next steps of diagnostics

__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #2  
Old 05-13-2019, 09:17 AM
Senior Member
 
Join Date: Nov 2002
Posts: 829
what is on pins 8 and 14? don't have a good enough memory for that system.
Reply With Quote
  #3  
Old 05-14-2019, 11:39 AM
I told you so!
 
Join Date: Jun 2002
Location: Motor City, MI
Posts: 2,853
Pin 8 codes:
25 - CMP sensor not recognized or implausible
33 - Maximum retard setting on at least one cylinder has been reached or the ignition angle deviation between the individual cylinders is greater than 6 degrees crankshaft angle
38 - Adjustable camshaft timing solenoid - open/short to ground or B+

Pin 14 code:
4 - Cruise control switch (S40)

I'm not sure what these codes add up to. Have you cleared the codes to see which ones recur? What about primary codes from the diagnostic module (apart from Pins 8 and 14)?
__________________
95 E320 Cabriolet, 159K
Reply With Quote
  #4  
Old 05-14-2019, 11:51 AM
Senior Member
 
Join Date: Nov 2002
Posts: 829
ok, pin 8 is the engine, whats pin 14? once i know what system, i can get code definitions. that's what i was asking.
Reply With Quote
  #5  
Old 05-14-2019, 12:31 PM
I told you so!
 
Join Date: Jun 2002
Location: Motor City, MI
Posts: 2,853
Pin 8 is ECU.
Pin 14 is CC/ETA per my notes.
Reply With Quote
  #6  
Old 05-14-2019, 01:07 PM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
I think I’m going to drop the car off at the indie shop next week for a better diagnosis. I’m out of ideas and tossed a lot of parts at the car. For the miss I checked to see if the plug wires were grounding out.. didn’t see any light show .. regapped the plugs..nothing. It could be a plug wire or a coil just guessing.

Then as for the cam codes I need to have an more experienced eye look at it. I know the timing is good. I need to see why it’s not getting a signal. I do have voltage and continuity at the cam sensor. One thing is that it idles smooth and drives beautiful but compared to my other e320 it Is lacking alot of power. My 94 pulls like a freight train and has about 300k miles in it.
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #7  
Old 05-16-2019, 09:32 AM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
Is it possible that I used the wrong engine harness? There’s two types
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #8  
Old 05-16-2019, 10:16 AM
I told you so!
 
Join Date: Jun 2002
Location: Motor City, MI
Posts: 2,853
No. You would have noticed right away as two connectors would have been completely different. I was initially sent the wrong one when I replaced mine.
__________________
95 E320 Cabriolet, 159K
Reply With Quote
  #9  
Old 06-04-2019, 08:02 AM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
Swapped the ecu from my 94 to the 95 and it runs 80 percent better and only has the 25 code and a flat power band. However at the same time the 94 with the 95 ecu still runs perfect and the issues that the 95 had aren’t transferred over. So many wierd issues. Having doubts that my updated engine harness is any good. Running out of ideas
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero

Last edited by speednjay; 06-04-2019 at 10:31 AM.
Reply With Quote
  #10  
Old 06-06-2019, 05:48 PM
Registered User
 
Join Date: Nov 2010
Location: TX
Posts: 3,978
Quote:
Originally Posted by speednjay View Post
Swapped the ecu from my 94 to the 95 and it runs 80 percent better and only has the 25 code and a flat power band. However at the same time the 94 with the 95 ecu still runs perfect and the issues that the 95 had aren’t transferred over. So many wierd issues. Having doubts that my updated engine harness is any good. Running out of ideas
Are you positively sure the camshaft sensor is generating a signal?
__________________
2012 BMW X5 (Beef + Granite suspension model)

1995 E300D - The original humming machine (consumed by Flood 2017)
2000 E320 - The evolution (consumed by flood 2017)
Reply With Quote
  #11  
Old 06-06-2019, 07:57 PM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
Quote:
Originally Posted by Zulfiqar View Post
Are you positively sure the camshaft sensor is generating a signal?
Nope. Ive bought a new cam sensor.. swapped out the sensor from my 94 which i know is a working part. Even dropped the car off at the Mercedes Indy shop thinking they would have better diagnostics, plug the car into star...but all they did was swap parts around too. I need to get an oscilloscope and confirm that
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #12  
Old 06-07-2019, 03:45 PM
Registered User
 
Join Date: Nov 2010
Location: TX
Posts: 3,978
Quote:
Originally Posted by speednjay View Post
Nope. Ive bought a new cam sensor.. swapped out the sensor from my 94 which i know is a working part. Even dropped the car off at the Mercedes Indy shop thinking they would have better diagnostics, plug the car into star...but all they did was swap parts around too. I need to get an oscilloscope and confirm that
The indy shop would have an oscilloscope already, ask them to probe it.

Also go over the wiring harness connections to the ECU and all pins and compare it to the factory diagram, on my old E300 the idle pinouts to the control module were messed and it would idle at 1100 rpm all the time.

The wiring was packaged perfectly original and nice with updated delphi part no. Once I corrected the wrong pins the idle was rock steady at 650 rpm.
__________________
2012 BMW X5 (Beef + Granite suspension model)

1995 E300D - The original humming machine (consumed by Flood 2017)
2000 E320 - The evolution (consumed by flood 2017)
Reply With Quote
  #13  
Old 06-08-2019, 04:34 PM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
I’m not going to take it to the shop again. I shouldn’t have to babysit an experienced Mercedes tech especially when I pay $140/hour


Found a short in the cam sensor wire. So I’m trying to fix that. It’s not just in 1 spot if I wiggle the wire it’ll short out throughout. Anyone have a spare cam wire from an old rotted harness?
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #14  
Old 06-13-2019, 07:55 PM
Registered User
 
Join Date: May 2010
Location: BAKERSFIELD, CA
Posts: 1,466
Still getting the pin 8 25 and 33 code. This car is getting frustrating. The w124 is a cool car but the electrical gremlins are killing it. I guess the next step is to completely change out the cam sensor wire from ecu to sensor
__________________
1993 e300
1995 e320
1994 e320
2006 s500 4matic
2004 Jeep wj overland
2001 Ducati 748
2004 Honda shadow aero
Reply With Quote
  #15  
Old 06-14-2019, 04:36 PM
Registered User
 
Join Date: Nov 2010
Location: TX
Posts: 3,978
As you dont own equipment to see the sensor inputs at the ECU - it will become very frustrating.

You need to find a small oscope to see if you are seeing signal at the ECU itself from any sensor which is throwing errors, This is how these cars were repaired when they were common.

The mercedes diag software for this can show you this data too.

__________________
2012 BMW X5 (Beef + Granite suspension model)

1995 E300D - The original humming machine (consumed by Flood 2017)
2000 E320 - The evolution (consumed by flood 2017)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 09:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page