|
|
|
|
|
#1
09-27-2002, 07:48 AM
|
||||
|
||||
|
How to replace lock mechanism in door?
I have to replace the lock mechanism on the driver door of my M-class. How do they get that thing out of there? I've loosened it, but it won't unattach itself from the door handle. It looks like I may have to take the handle off, but I can't see how that is done either. It also does not look like there is enough room to pull the unit out of the panel either,
Help!
__________________
Michael LaFleur '05 E320 CDI - 86,000 miles '86 300SDL - 360,000 miles '85 300SD - 150,000 miles (sold) '89 190D - 120,000 miles (sold) '85 300SD - 317,000 miles (sold) '98 ML320 - 270,000 miles (sold) '75 300D - 170,000 miles (sold) '83 Harley Davidson FLTC (Broken again) :-( '61 Plymouth Valiant - 60k mikes 2004 Papillon (Oliver) 2005 Tzitzu (Griffon) 2009 Welsh Corgi (Buba) 
|
|
#2
09-29-2002, 12:33 PM
|
||||
|
||||
|
Anybody?
I have to open the driver door from the inside until I get the latch replaced. I have a replacement, but can't figure out how to get the old one out.
__________________
Michael LaFleur '05 E320 CDI - 86,000 miles '86 300SDL - 360,000 miles '85 300SD - 150,000 miles (sold) '89 190D - 120,000 miles (sold) '85 300SD - 317,000 miles (sold) '98 ML320 - 270,000 miles (sold) '75 300D - 170,000 miles (sold) '83 Harley Davidson FLTC (Broken again) :-( '61 Plymouth Valiant - 60k mikes 2004 Papillon (Oliver) 2005 Tzitzu (Griffon) 2009 Welsh Corgi (Buba)
|
|
#3
09-30-2002, 07:28 AM
|
||||
|
||||
|
Can someone help me here?
How do I remove the door latch from my W163?
__________________
Michael LaFleur '05 E320 CDI - 86,000 miles '86 300SDL - 360,000 miles '85 300SD - 150,000 miles (sold) '89 190D - 120,000 miles (sold) '85 300SD - 317,000 miles (sold) '98 ML320 - 270,000 miles (sold) '75 300D - 170,000 miles (sold) '83 Harley Davidson FLTC (Broken again) :-( '61 Plymouth Valiant - 60k mikes 2004 Papillon (Oliver) 2005 Tzitzu (Griffon) 2009 Welsh Corgi (Buba)
|
|
#4
09-30-2002, 04:24 PM
|
||||
|
||||
|
Not sure if this will help or not:
The 126 has a plug on the door jamb, remove it and pull a single phillips head screw. Then slide the handle assembly forward to disengage the mechanism and lift out. Take a look on the "M" and see if there is a plastic plug in line with the handle, then take a looksee under the plug.
__________________
Mike Tangas '73 280SEL 4.5 (9/72)- RIP  Only 8,173 units built from 5/71 thru 11/72 '02 CLK320 Cabriolet - wifey's mid-life crisis 2012 VW Jetta Sportwagon TDI...at least its a diesel Non illegitemae carborundum.
|
 |
| Bookmarks |
|
|
Linear Mode
