|
|
|
#1
|
|||
|
|||
Hi,
The seam (the "round tubing" that goes around the armrest) on my 88 300E Front Centre Armrest has broken into several pieces (but it's still attached to the armrest). When I wear a short sleeve shirt, the broken seam cuts into my elbow, causing it to bleed!! Is there anyway that I can fix this other than replacing the entire armrest? If I need to replace it, how much is it and does partsshop carry it? My interior color is Palomino. Thanks again. This is a great site! |
#2
|
|||
|
|||
Yes the cover can be replaced and it is the only way I know of to repair this. It is easy to do. Just submit a parts request form to Partshop and be sure to include the color of your interior.
------------------ Benzmac: ASE CERTIFIED MASTER AUTO TECHNICIAN SERVICE MANAGER FOR 14 BAY FACILITY MERCEDES SPECIALIST 8 YRS PARTNER IN MERCEDESSHOP.COM |
#3
|
||||
|
||||
I had the same thing happen...tried to epoxy it and just made a mess! The cover's fairly reasonable (about $50-60 if I recall) and takes an upholsterer almost no time to change it out. Good luck!
Michael '88 300TE '92 500E ------------------ |
#4
|
|||
|
|||
Is it too difficult for a DIYer to do it?
Thanks. |
#5
|
|||
|
|||
I had mine broken in 2 places, the breaks were very clean, i.e. Straight line breaks.
After looking at it a awhile, and recently purchasing a O-ring kit for another project, I started thinking what the heck . The bead or piping, as it is called in the upholstry biz, looked like a beige o-ring. In the kit is a length of o-ring rubber that allows you to make you own size from the material. The way you join the ends is with superglue. This kit had a Loctite product, but no different than any other superglue. It even says that if you run out or it dries up before fully used you can use any brand that works with rubber or plastic. I wouldn't recommended this for the shuttle though. Short story is, that I treated the piping like an o-ring and put a drop on the break points, pushed in the leather surrounding the piping which aligned the piping together and held for 60 seconds, (Make sure piping is clean with alcohol or something similar). Viola, It no longer snags my shirt or draws blood, You can't tell where it broken anymore. Be careful with the glue and also acetone if you use it to clean up residual glue afterwards. Good Luck, ------------------ Mike Mullins 71 250 Coupe 92 400E Sedan 90 944/S2 Cabriolet |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
300e Door Panels....All 4 Tan and Front Blue FS!! | 6cndmbz | Mercedes-Benz Used Parts For Sale & Wanted | 0 | 06-13-2004 01:32 AM |
*CLEAN* W124 Gray MB-Tex Front Seats / 300E 260D 300D (300E 2.8) and (W124 Wagons) | FA22 | Mercedes-Benz Used Parts For Sale & Wanted | 5 | 03-01-2004 08:40 PM |
wtb: front armrest for 93/94 E series and /or rubber bands | johnp352 | Mercedes-Benz Used Parts For Sale & Wanted | 9 | 12-23-2001 07:20 AM |
How hard is to replace transmission front pump seal on a 1988 300E? | Steve190E 2.3 | Tech Help | 3 | 04-03-2001 08:23 AM |
Replacing Front Speakers - 1988 300E 2.6 | Philipasmith | Car Audio and Multimedia | 3 | 10-28-1999 02:13 AM |