Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Closed Thread
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-06-1999, 01:01 AM
Chris Ecklund
Guest
 
Posts: n/a
Now this isnt a useless bit of info, but one that royally had my knickers in a knot, as I have been planning my first oil change for months, and then I learn that the ramps I bought wont fit under the front body work!!!!

What a let down, I was all ready to do the oil change, and then this!

I guess I have to go buy a Jack and report back.

------------------
Chris Ecklund
98 300 DT


  #2  
Old 09-06-1999, 01:09 AM
Bill Wood's Avatar
Retired Webmaster
 
Join Date: Mar 1999
Location: Johns Creek, GA, USA
Posts: 5,013
Why not use a "Topsider" and change your oil by sucking it out of the dipstick tube? It works great. We're thinking about doing a DIY article on topside oil changes.

------------------
Bill Wood - Webmaster
MercedesShop.com, LLC


  #3  
Old 09-06-1999, 08:22 AM
Moderator
 
Join Date: Mar 1999
Location: Tucker, Ga USA
Posts: 12,153
On our alignment rack I use some 2" X 12s on the approach to keep the front from hitting the ramps. Most lowered cars have this problem.
  #4  
Old 09-06-1999, 11:07 AM
E55 KEV's Avatar
www.E55AMG.com
 
Join Date: Jul 1999
Location: Washington D.C.
Posts: 571
Try a set of "Rhino Ramps" they are supposed to be designed for low front ends (have not tried them). They are made of some high quality plastic unlike my old rusted metal ramps and are very lightweight and look pretty cool. They can be found at Pep Boys for $29.99 and AutoZone for $24.99 or $29.99 (I have seen both prices). Some Internet/Mail Order sell them for $49.99. Hope this helps.
  #5  
Old 09-06-1999, 02:21 PM
Registered User
 
Join Date: Jul 1999
Posts: 239
After deciding ramps are too much trouble,
I've been draining the oil in three different makes of cars (300SD, Volvo 745 and Camry V-6) without the use of ramps.
Depending on the car and the location of the drain plug, crank the steering wheel one direction or the other (you'll have to figure out which way) and the plug should be reachable through the wheel well.
I do wear overalls, rubber gloves, etc. and use a piece of carpet as it does require lying down on the floor.
Once the routine is worked out, it goes a lot quicker then setting up ramps, plus in most cases you get a more complete drain if the car is level.
Maybe it's just lucky coincidence that I've been able to do this in these cars.
(I'm able to replace the oil filters from above the engine compartment.)


[This message has been edited by VA300SD (edited 09-06-1999).]
  #6  
Old 09-06-1999, 11:31 PM
Chris Ecklund
Guest
 
Posts: n/a
I have heard and read a lot about the topsider, but I just do not feel comfortable about not seeing what is coming out from the pan.

But thanks for the tip about using the pieces of wood, and since there is new houses going up everywhere, this should be no problem in finding some

If this doesnt work, I might just try the cranking the wheel trick also, thanks for the tips!!

------------------
Chris Ecklund
98 300 DT
  #7  
Old 09-07-1999, 04:02 PM
Philipasmith
Guest
 
Posts: n/a
Where does one get a hold of one of these "Topsiders"?

Phil
  #8  
Old 09-07-1999, 06:48 PM
Bill Wood's Avatar
Retired Webmaster
 
Join Date: Mar 1999
Location: Johns Creek, GA, USA
Posts: 5,013
Chris-
Many of the dealers are doing top side oil changes now. M.B.DOC swears by it. The new ML is actually designed for top side changes and trying to do it any other way can make a real mess. You can see your oil thru a small plastic tube as it is sucked out.

Phil-
I bought my Topsider at BOATER'S WORLD here in Atlanta. Any good marine supply store should have one. It was $45. It holds a little over 8 quarts of oil...perfect for my E430. Since my oil filter is located in the top / front of the engine, oil & filter changes are a snap.




------------------
Bill Wood - Webmaster
MercedesShop.com, LLC




[This message has been edited by Webmaster (edited 09-07-1999).]
  #9  
Old 09-07-1999, 07:34 PM
Registered User
 
Join Date: Jul 1999
Posts: 239
Darned thing looks like a gas can painted blue with a suction pump mounted on one of the cap holes.

Anyway, how does one know if the hose is in deep enough to get most of the oil out ?
Also, would the hose fit in through dip stick tubes of 81 300D and 81 300SD ?
Maybe someone could mention the diameter of the hose that feeds into the tube ?
Yet another gadget I'd like to own.

[This message has been edited by VA300SD (edited 09-07-1999).]

[This message has been edited by VA300SD (edited 09-07-1999).]
  #10  
Old 09-08-1999, 01:56 PM
Bill Wood's Avatar
Retired Webmaster
 
Join Date: Mar 1999
Location: Johns Creek, GA, USA
Posts: 5,013
The part that goes into the dipstick tube is 1/4" flexible plastic tubing. The tubing is more than long enough to reach the bottom of the oil pan. All Mercedes since the mid '70s have dipstick tubes that go to the bottom of the oil pan. Just keep feeding tubing until you bottom out on the oil pan...then back off a little so you don't create a vacuum against the bottom of the pan or for best results cut the end of the tube at 45 degrees. Here's the way you use it:

1) Make sure your oil is warm but not hot.

2) Pinch off the large diameter plastic hose with the hose clamp.

3) Pump the bicycle pump about 50 times to create a vacuum in the can.

4) Insert the small plastic tube into the dipstick tube.

5) Release the clamp.

6) Loosen your oil filter to allow oil to drain out and then replace oil filter.

7) Wait about 10 minutes until you start to hear a gurgling sound.

8) Slowly push the tube up and down to get the last few drops sucked out.

The Topsider also includes 2 caps to replace the pump and tubing connection so you can seal the can for transport to your recycling center. Nothing could be easier!

------------------
Bill Wood - Webmaster
MercedesShop.com, LLC


  #11  
Old 09-08-1999, 02:00 PM
Philipasmith
Guest
 
Posts: n/a
Bill,

Thanks, your reply helped out a lot!

Phil
  #12  
Old 09-09-1999, 10:01 AM
Registered User
 
Join Date: Jul 1999
Posts: 239


Thanks for the very thorough answer, Bill.

In particular the diameter of the hose and the reach of the dip stick tube.

I'm guessing this thing will be handy for other makes of cars.
  #13  
Old 09-09-1999, 03:41 PM
mh mh is offline
Registered User
 
Join Date: May 1999
Location: irvine,ca,usa
Posts: 5
I have used the topsider for my toyota van and the E320. Worked great for both. On the toyota van, I removed the drain plug after using the topsider, and guess what? not a single drop of oil came out.

Mark
  #14  
Old 09-10-1999, 12:29 AM
Registered User
 
Join Date: Jul 1999
Posts: 239
I am running into deadends trying to locate this Topsider locally.
Can someone provide me with the name of the manufacturer so I can find a mail order source or the nearest dealer ?
My other option is the local boat dealer sells the heavy duty pumps for about the same price as the Topsider gizmo.
Thanks.
  #15  
Old 09-10-1999, 10:52 AM
Rick Miley's Avatar
Spark Free
 
Join Date: Jun 1999
Location: Land O Lakes, FL
Posts: 3,086
Try this: http://www.boatus-store.com/MC_Online/Browse.asp?ShowItem=1708

There is a list of several pumps, including the Topsider.

------------------
Rick Miley
Tampa, FL
99 E300DT
86 190E
87 300E


Closed Thread

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wal Mart lawsuit...nonsense or not? mikemover Off-Topic Discussion 11 07-02-2004 03:45 AM
Autocrossing a 400E and 300TE 400ERACER Mercedes-Benz Performance Paddock 9 06-05-2004 02:50 PM
FS W140 S600 grill, May fit W124 E-Class with modification yellowamg Mercedes-Benz Used Parts For Sale & Wanted 3 08-28-2003 04:48 PM
Wheels from which other MB will fit my 500E aldedmon Mercedes-Benz Wheels & Tires 2 03-14-2003 08:14 AM
Will Rims From An E Class Fit My 380sl? Help! hudson66 Mercedes-Benz SL Discussion Forum 1 01-19-2003 11:14 AM



All times are GMT -4. The time now is 04:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page