Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help

Go Back   PeachParts Mercedes ShopForum > Technical Information and Support > Tech Help

LinkBack Thread Tools Display Modes
Old 01-05-2003, 11:17 AM
Registered User
Join Date: May 2002
Posts: 27
Unhappy 126/560SEL heater flap

Merc is a 1986 560SEL USversion.

I have diagnosed my "cold feet" problem to the fact that the heater door does not retract once the defrost closes is. In other words-- if i push leftmost defrost switch the heater flap door closes properly directing all heat to the windows-- when i hit normal heat button the flap door does not retract at all. The pass side works fine.

My question is for those experienced here are what are the next things to check here and how can i possibly get to the flap control actuator. I have looked and looked and cant see the control.

Reply With Quote
Old 01-05-2003, 12:11 PM
Registered User
Join Date: Aug 2000
Posts: 106
You may have the same problem I do, if all your vacuum elements are working. The actuaters are inside the box, my left one also sticks and I have tried many tricks like spraying silicone lube on it from the right side. It is some kind of siscor linkage off the vacuum valve. I gave up and wedged a piece of wood against the flap, this summer I will pull it out for a/c
Reply With Quote
Old 01-06-2003, 07:15 PM
Registered User
Join Date: Jan 2003
Location: Dallas
Posts: 776
Algae 1, This is my first post, though I have been a closet reader for 2 years at least. This one really hit home, and I just had to reply. You won't like what I'm about to tell you I'm afraid.

The exact same cold-feet thing occurred on my '91 300SE. I discovered the left footwell door hinge was broken. Here's the drill:

The two footwell doors are on either side of the bottom of the big black heater box. They are simple squares of plastic, with the hinge being vertical posts that just slip into recesses in the heater box. The upper post extends thru a hole in the box, and a plastic lever attaches to it. This lever is actuated via a complex array of metal arms that ties the left and right doors together, and then ties them to the vacuum actuater. it's really a simple implementation, MB just over-complicated it.
The vacuum actuater is the one directly behind the radio/climate control, right in the center of the dash. To confirm it's working, you have to remove the ash tray, coin tray, radio, and probably the climate control enough to see back there. As you turn the heat knob to-from full hot to full cold, you should see the vacuum actuater move the series of rods and levers going to both L and Rt doors. Of course the bad news is that the Left door is so hidden by the console and wires, tubes, etc; you can't see if it is really working even if the actuater arm is moving.
unfortunately on mine, the vertical post/hinge on the door was broken, and the actuater arm just rotated around, not opening the door. If your actuater arm moves on the left side, I'll bet you have that same broken-post issue.

I was able to buy a new door at the dealer for $20. But installation was a real bear. I removed the center console, left kick panel onthe console, lower left dash and knee bolster, and all the venting, specifically the big metal corrugated pipe under the knee bolster. These are all pretty straight forward but very time-consuming. After getting to the left door, I saw no way to install the new door, as the post/hinge needed to protrude thru the heater box hole by almost an inch, and there was no way to install it without removing the heater box and disassembling it. This would have been a few days (literally) of teardown.

After much thought, I came upon a solution: I took a drill and Dremel, and cut out a section around the post/hinge hole about 2 inches square, pulled that section of the box back, and slipped in the new door. JB Weld was then applied to replace the section of the box, and all was good.

Well, i told you you wouldn't like it. Course, it might be the vacuum, or maybe the actuater linkage just came loose. Pull the radio and peer back there and it will be clearer what to look for. If you want to proceed, I can give nitty-gritty details on removing every screw; I still see it in my sleep.

Good luck,
S-Class Guru
Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

All times are GMT -4. The time now is 07:13 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page