Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 03-23-2003, 07:41 PM
Registered User
 
Join Date: Jan 2003
Posts: 259
rough idle on 91 560 SEL

my car started to have rough idle a couple of days ago. I searched this site and have removed the air cleaner housing and inspected all vacuum lines that I could see, but could not find any that is disconnected nor any that would appear to be broken.

Let me be more specific, perhaps it will narrow down my symptoms:
1. rough at idle
2. appears to run normal as it approaches about 40 mph.
3. Trans shifts normally
4. gauges appear to function normally ( idle at 600rmp, oil at about max during idle and in gear)
5. starts normally.

thx in advance for your help.

emmy
91 560 sel

Reply With Quote
  #2  
Old 03-24-2003, 09:38 AM
moedip
Guest
 
Posts: n/a
DO A SEARCH FOR ROUGH IDLE 560SEL - This subject has been discussed in depth many many times. You will find the cure with your search.
Reply With Quote
  #3  
Old 03-24-2003, 11:46 AM
Registered User
 
Join Date: Jan 2003
Posts: 259
thx for the input. I have actually searched and read all the posts, and I have the following as my plan to inspect:
1. idle control valve
2. idle air valve
3. Fuel injector nozzles(holders, hoses, guides)
4. recheck all vaccuum lines

I would appreciate if there are more tips/guidance from the experts.

thx again,
emmy
Reply With Quote
  #4  
Old 03-24-2003, 12:05 PM
moedip
Guest
 
Posts: n/a
You missed my thread on the fuel distributor screens getting partially plugged from rust from a rusted fuel line. After 1 year or more of a miss at idle - new fuel lines and cleaning the screens to the injector lines cured my miss at idle. Just to be clear - my miss was not major - just annoying to see engine move and feel the random miss. Pick up and acceleration was perfect.
Reply With Quote
  #5  
Old 03-24-2003, 03:38 PM
Registered User
 
Join Date: Jan 2003
Posts: 259
thx for the reminder.

Would you know where the idle control valve and the idle air valve are located at in a 91 560 SEL? not sure if these are one and the same..

thx
Reply With Quote
  #6  
Old 03-24-2003, 04:17 PM
Registered User
 
Join Date: Sep 2002
Location: Kingsport, TN
Posts: 375
Hi emmydotnet,

I think they are the same and it is located in front of the distributor under the air filter housing on a 87 420:

Good luck

Reinhard Kreutzer
Attached Thumbnails
rough idle on 91 560 SEL-idle-control-valve-air-filter-housing-off.jpg  
Reply With Quote
  #7  
Old 03-24-2003, 04:20 PM
Registered User
 
Join Date: Sep 2002
Location: Kingsport, TN
Posts: 375
It's the longish cylinder with the rubber hoses at the top and side and the connector at the other end. When in idle, pulling of the electric connector should increase the idle speed. Otherwise, it means the valve is clogged.
Reply With Quote
  #8  
Old 03-24-2003, 08:46 PM
Registered User
 
Join Date: Jan 2003
Posts: 259
thx for the input.

OK, so when I disconnected the idle control valve, the idle went up, but still rough idle. does this mean that there is nothing wrong with the idle control valve?

I also noticed that the air intake into the carb ( about 5 in diameter) has a little bit of an opening (about 1/8" maybe a little smaller) after start-up with engine still cold. Is this normal? or does this indicate some vacuum leak somewhere?
Reply With Quote
  #9  
Old 03-24-2003, 11:46 PM
Registered User
 
Join Date: Sep 2002
Location: Kingsport, TN
Posts: 375
Well Emmy,

it means the idle control valve is not stuck. Cleaning still might help a bit.

I would start with an injector cleaner to add to the fuel and see what that does to the idle. It's a rather complex system and this is the cheapest start.

Good luck

Reinhard Kreutzer
Reply With Quote
  #10  
Old 03-25-2003, 11:59 AM
Registered User
 
Join Date: Jan 2003
Posts: 259
i have not considered the plugs, plug wires and dist cap since it runs smoothly at about 40mph and up. good point though. i will do that.

I have also read some posts on spraying carb cleaner over specific vacuum line to troubleshoot hard to see broken lines. Any comment on this method?

with the other recommendation, i found a local vendor for the injector cleaner BG 44K. Sounds like a lot of people are happy with this additive - although pricey at $17 a can. I will try this today.
Reply With Quote
  #11  
Old 03-26-2003, 01:58 AM
Registered User
 
Join Date: Jan 2003
Posts: 259
I added the BG 44K to my full tank, drove it hard for about 40 miles and bingo! the rough idle was gone. I started to notice some improvement after about 20 miles with only random miss at idle. The idle was smooth after about 40 miles. This stuff is amazing...it works! I will observe for the next few days to see if it holds up...

Reinhard Kreutzer, thanks for the tip.
Reply With Quote
  #12  
Old 03-26-2003, 09:21 AM
moedip
Guest
 
Posts: n/a
Been there and done that - same results - temporarily. If problem returns after about 500 miles-- more cleaner - smooth idle - problem returns--- if this happens to you - suspect rust inside fuel lines clogging screens in fuel distributor. Hope you are right and I am wrong.
Reply With Quote
  #13  
Old 03-26-2003, 05:44 PM
Registered User
 
Join Date: Sep 2002
Location: Kingsport, TN
Posts: 375
Hi emmydotnet,

I pass that "thank you" on to all the others who have mentioned it before...

You are also to change the oil after this treatment to get rid of whatever made it into the oil...

Regards

Reinhard Kreutzer
Reply With Quote
  #14  
Old 04-09-2003, 03:49 PM
Registered User
 
Join Date: Jan 2003
Posts: 259
i need to update my situation. after the full tank with the BG 44K was consumed, the rough idle came back. in addition, the engine now dies randomly at any speed. It would however recover by itself, sometimes, but other times I would have to restart it. It does restart all the time. now i am back to square one with the rough idle, and the engine cutting out randomly in addition. Fuel pump relay, and injectors, and rusted fuel lines seem to be the well discussed causes in this forum.

The fact that the idle improved when i used BG 44K tells me that it is injector related. The fact that the rough idle came back tells me that something is making my injectors go bad. Could it also be ignition related?

The engine cutting off/ and recovering tells me that somehow the fuel pump relay is defective or the signal triggering the relay is failing in ramdom. I recall one post mentioning about some other device that triggers the relay to let it know that it should turn on to start the fuel pumps. any ideas on this?

Any related leads would be appreciated.
Reply With Quote
  #15  
Old 04-09-2003, 04:52 PM
Registered User
 
Join Date: Feb 2002
Location: Orlando, FL
Posts: 788
moedip: how difficult was it to change the fuel lines? How many are there? Can you order all that is necessary from fastlane? Thanks!

__________________
'86 420SE Euro
904 Midnight Blue, Gray Velour
Dad bought it new, now I own it.

"A Mercedes-Benz is like a fine wine, it only gets better with age."
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 10:04 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page