Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 05-20-2003, 12:58 AM
Registered User
 
Join Date: Mar 2002
Location: San Francisco, CA
Posts: 71
Angry Can't Believe a 190e is More Difficult to Service Than a 944 Turbo

Hello all, I must apoligize in advance for the rant but I just cannot believe that a 190e can be more of a pain in the rear to service than my 944 Turbo. I have an 87 190e 2.6 and just tried ti change the serpentine belt. As you can guess I have been defeated tonight. I bought the fan clutch holder and the special 8mm hex tipped socket ( the Mercedes one not the Pep Boys special). Just the socket alone will barely fit between the radiator and the fan let alone the mini 3/8 drive breaker bar or socket wrench. I was hoping not to have to remove the radiator and front bumper on this car just to change a stupid belt...and it's not even a timing belt. Who designed this? Sorry for the rant but It takes less than fifteen minutes to change a serpentine belt on my VW...yes, I know it isn't of the same caliber of a Mercedes....but come on, this is rediculous. To have to remove a radiator and front bumper of a car just to change a serpentine belt??? Who ever designed/worked on this part of the car should be shot.

Reply With Quote
  #2  
Old 05-20-2003, 01:14 AM
azhari
Guest
 
Posts: n/a
Fan & fan shroud removal first?

I have a 1.8 and i think that there is more "workspace" in the engine bay than a 2.6 so maybe it is easier to change the belt on my car.

That would explain your pain...

Would it have been easier if you had removed the fan and fan shroud first?

Just a thought.
Reply With Quote
  #3  
Old 05-20-2003, 01:32 AM
Registered User
 
Join Date: Mar 2002
Location: San Francisco, CA
Posts: 71
Actually, the socket is used to remove the nut holding the fan on the fan clutch and the shrouds were moved away. There is a 3/4" clearance gap between the radiator and the fan. They really shoehorned this engine in there.
Reply With Quote
  #4  
Old 05-20-2003, 04:43 AM
Registered User
 
Join Date: Sep 2002
Location: Newcastle upon Tyne, UK
Posts: 215
The story goes that the 190 was deliberately designed so that a six cylinder engine would not fit, and it would only ever have the four. However, MB engineers were more ingenious that the designers, and managed to squeeze the six in.

I don't know if this story is true, or just an urban myth, but it's easy to believe when you look at the engine bay.
__________________
Cheers, Neil
Reply With Quote
  #5  
Old 05-20-2003, 11:06 AM
Rick Miley's Avatar
Spark Free
 
Join Date: Jun 1999
Location: Land O Lakes, FL
Posts: 3,086
If you're still defeated, go to http://www.sears.com and search for "socket cap set". Invaluable for those tight spaces.
__________________
Rick Miley
2014 Tesla Model S
2018 Tesla Model 3
2017 Nissan LEAF
Former MB: 99 E300, 86 190E 2.3, 87 300E, 80 240D, 82 204D Euro
Chain Elongation References
Reply With Quote
  #6  
Old 05-20-2003, 11:14 AM
Registered User
 
Join Date: Mar 2003
Location: Southern California
Posts: 2,272
Basically a true story, but the details are a little different. When designing the 201, installation of a six was not envisaged. The 201 design began in the late seventies and was MBZs response to the energy crisis, so only a four cylinder engine was planned, but when fuel prices dropped the engineers got creative. The 201/2.6 was first shown at the Tokyo Auto Show, circa '86. In production the early 2.6s have front end sheet metal that is 3mm longer than the fours, and you can verify this by looking at the front overhang spec and overall length. This fooled a lot of body shops!

Circa 1990/91 the longer front end became standard for all 201s.

As far as the belt change is concerned, I haven't done it, but picked up the following procedure off this forum.

"Slacken the large bolt (17mm) that goes through the centre of the tensioner. Then loosen the adjuster nut (13mm) and the pulley moves back so you can fit the new belt. Set the adjustable plastic arrow at the end of the cast triangle and tighten until it's at the other end. Finally, tighten the 17mm nut."

Duke
Reply With Quote
  #7  
Old 05-20-2003, 12:19 PM
Registered User
 
Join Date: Apr 2000
Location: Indianapolis
Posts: 109
My W124 manuals have a NOTE saying something to the effect that an alternative way to replace the belt is to loosen the alternator bolts and tip it to the side to remove tension from the belt".

Haven't tried this, makes sense though, and it's straight out of the factory manual.

Brian
Reply With Quote
  #8  
Old 05-20-2003, 09:12 PM
Registered User
 
Join Date: Jan 2003
Location: Sydney, Australia
Posts: 627
Seviceability

The issue of serviceability is one reason I actually have a preference for the 2.3 M102 (4 cyl) in my 190E. Whilst I love the sweet, smooth and revvy M103 (6 cyl) like in our 300TE and would have liked the extra performance of the 2.6 in the 190E, I do not like the way it is shoe-horned in there. The W201 also gives sharper handling with the lighter four. Indeed, the W124 is also claimed to handle better with the four but the extra power and smoothness is nice in the larger car.
__________________
107.023: 350SLC, 3-speed auto, icon gold, parchment MBtex (sold 2012 after 29 years ownership).
107.026: 500SLC, 4-speed auto, thistle green, green velour.
124.090: 300TE, 4-speed auto, arctic white, cream-beige MBtex.
201.028: 190E 2.3 Sportline, 5-speed manual, arctic white, blue leather.
201.028: 190E 2.3, 4-speed auto, blue-black, grey MBtex.
201.034: 190E 2.3-16, 5-speed manual, blue-black, black leather.
Reply With Quote
  #9  
Old 05-20-2003, 10:04 PM
ILUVMILS's Avatar
Senior Member
 
Join Date: Sep 2002
Posts: 3,066
Don't panic. It's not as bad as it looks! The upper radiator support/cross-member can be loosened and set to the side. This will give you enough room to remove the fan. Just remove the six 10mm bolts(three on each side), as well as the two in the center, in front of the A/C condenser. The hood release cable can be left alone. The upper radiator support can then be lifted up out of the way. The radiator can then be tilted forward enough to allow you to remove the fan safely. I know it's tight, but it works. I've done it hundreds of times. Let us know how it goes.
Reply With Quote
  #10  
Old 05-21-2003, 10:18 AM
csnow's Avatar
Registered User
 
Join Date: May 2002
Location: Mass
Posts: 1,127
I'm not sure the clearance situation is all that much better on the 124.

Instead of the special hex key socket tool, just use an ordinary L-key wrench. Grind off the short end as needed to get the proper length for clearance, and put a short length of 3/8 steel pipe on it for extra leverage.

I also cut my fan shroud in half for easy removal. Cuts are at 12 and 6 o'clock, and zip ties through a couple of drilled holes hold it together. Not 'pretty', but very practical.
__________________
1986 300E 5-Speed 240k mi.
Reply With Quote
  #11  
Old 05-21-2003, 11:18 AM
azhari
Guest
 
Posts: n/a
Just saw a photo of the engine bay in a 6 cyl 190e.

Oooooohhhhhh...not good.

Really tight fit.

mbsickness, i share your grief...
Reply With Quote
  #12  
Old 05-21-2003, 11:19 AM
G-Benz's Avatar
Razorback Soccer Dad
 
Join Date: Apr 2001
Location: Dallas/Fort-Worth
Posts: 5,711
When I replaced my W124 serpentine belt, I removed the fan shroud first, (and you can carefully get it completely out of the engine bay without removing other parts).

I then loosened and removed the 3 7mm hex bolts from the fan and removed the fan blade out of the engine bay.

This allowed enough room to gain access to the belt.

The belt tension is such that you can easily pry a screwdriver between one of the pulleys and the belt and coax the belt completely off.

Did the reverse of the above procedures to install. Total replacement time: 30 minutes.

Total replacement time on the VW: 1 minute!
__________________
2009 ML350 (106K) - Family vehicle
2001 CLK430 Cabriolet (80K) - Wife's car
2005 BMW 645CI (138K) - My daily driver
2016 Mustang (32K) - Daughter's car
Reply With Quote
  #13  
Old 05-21-2003, 11:22 AM
Registered User
 
Join Date: Mar 2002
Location: San Francisco, CA
Posts: 71
Thanks for the input. I'll give it another try in a few days as my house is getting first priority. I think I will try to "lean" the radiator forward and see if that works. Other wise it will all come apart. Since I am changing the tensioner and shock, would it be better to remove the radiator anyway? Just a thought. Thanks.
Reply With Quote
  #14  
Old 05-21-2003, 03:01 PM
Registered User
 
Join Date: Aug 1999
Location: ajax, ontario, canada
Posts: 773
Quote:
Originally posted by Duke2.6
In production the early 2.6s have front end sheet metal that is 3mm longer than the fours, and you can verify this by looking at the front overhang spec and overall length. This fooled a lot of body shops!

Circa 1990/91 the longer front end became standard for all 201s.
amazing piece of trivia! - thanks Duke.

Looking at Carpoint verifies this - you can see the difference in overall length between a 1988 2.3 and 2.6.

the 1989 201s had the longer frontends as well.

this is useful to know, when trying to source fenders from the scrapyard.

it's also interesting to show your engine to people who don't know about the 190e2.6. When the hood is closed, they have an idea in their mind of the size of the engine, based on the size of the hood. When you open the hood, they are surprised by the size of the engine. I was - when I bought the car.

Last edited by bobbyv; 05-21-2003 at 03:06 PM.
Reply With Quote
  #15  
Old 05-21-2003, 03:37 PM
Registered User
 
Join Date: Dec 2002
Posts: 305
A tidbit of useless info from me....

The belt on a 126 chassis with the 3.0 can be changed with no tools at all.. If the tensioner is already set to the correct or acceptable tension, you can just grab the belt at the top pulley, and pull it right off.. assembly is the reverse.. So, if your'e stuck on the side of the road

Draw a diagram first.. The routing is tricky...

__________________
89 300SEL Money Pit

92 Blown Buick Ultra Pimpmobile 220K and adding 1K per week

88 Wagoneer Slightly modified (Not for soccer moms)

04 Kia Sedona with every option... NICE
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 10:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page