Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 04-12-2000, 12:07 AM
Registered User
 
Join Date: Mar 2000
Posts: 217
The front passenger door panel on my 124 has a terribly annoying rattle as I'm driving. It seems to me that the map pocket area is loose. While i'm driving, I push the map pocket sector "in", and the rattle goes away. How do i take off the panel, and tighten any screws? Or do i have to take the panel off at all?

Thanks in advance....


Agron
1989 300E (105K miles)

Reply With Quote
  #2  
Old 04-12-2000, 06:51 PM
Registered User
 
Join Date: Jan 2000
Location: New Bedford, MA USA
Posts: 1,583
Door panel has to come off. Most likely culprit is broken plastic retainer clip for lower part of door panel. Have included a couple of other posts here for you to take a look at. Good luck..

The map pocket stays on the door panel. Held on from the backside with screws and clips. After the lock cover and switch trim and pull handle are off,Remove the trim cover for the mirror as well. Lower the window and lift up from the bottom of the panel to disengage the plastic hooks from the door inner panel. Then lift up, disconnect the courtesy light pigtail lead and then remove the panel.

I had the same problem on my 87 300. The hook on the arm rest had broken, leaving the top bolt and aft hook, so the arm rest kind of flopped when pulled. It might be fixable, but takes luck and ingenuity. I had enough plastic stucture left on the arm rest that I was avble to fabricate a new hook out of .080 1/4 hard stainless sheet. I drilled two samll holes through the stainless and then vaery carefully match drilled two small holes into the remaining plastic on the arm rest. I finsihed it off with two part epoxy before installing screws. Everything worked fine, but it does take time and luck. Hope this makes sense, cause I'm afraid to take the panel off to take a picture for you! I think one of the hardest things is for the average joe to access material that is srtong and can still be worked with normal shop tools. If you don't have an aircompresser and die grinders, I would not try it. I can mail you some metal stock if you want to try it. E-mail me at home via the member listing info. I'll also look for posts.


[This message has been edited by jeffsr (edited 04-12-2000).]
Reply With Quote
  #3  
Old 04-12-2000, 11:48 PM
Registered User
 
Join Date: Mar 2000
Posts: 217
jeffsr:

Thanks for the reply, Im gonna try to hassle with it this weekend--see what happens. I'll let you know how it goes. Again, thanks alot, much appreciated

Agron
1989 300E (105K miles)

Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
weird 126 front end rattle Joseph Bauers Tech Help 7 02-13-2002 06:52 PM
sqeaking, moaning noise coming from right front wheel of 300SD RG5384 Diesel Discussion 5 07-29-2001 10:15 PM
Let's talk front end rattle, shall we? DEPRIEST Tech Help 9 10-20-2000 01:00 PM
300E Front Passenger Seat Agron80 Tech Help 2 08-09-2000 09:49 PM
Front passenger seat rattles mattd Tech Help 3 05-25-2000 10:27 PM



All times are GMT -4. The time now is 02:55 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page