Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-22-2003, 06:55 PM
Registered User
 
Join Date: Nov 2000
Location: Mustang, OK
Posts: 509
W201 power window won't go up

Howdy,

I've had this problem twice now and haven't been able to figure it out. My problem is that the power window rolls all the way down OK, but won't come back up. I'ts like there is a window stop in the door that keeps the switch from powering the window motor if it is all the way down. I don't feel any resistance when it is down that would indicate the window is stuck in the down position, it just feels the switch is not powering the motor. To fix the problem, I've just worked the window switch back and forth for a while until it finally comes back up.

Any suggestions? I don't think it is the switch. Once the problem is cleared it seems to go up and down OK.

Thanks,

Sholin

__________________
What else, '73 MB 280 SEL (Lt Blue)
Daily driver: '84 190D 2.2 5 spd.
Reply With Quote
  #2  
Old 08-22-2003, 08:52 PM
Gilly's Avatar
Registered User
 
Join Date: Mar 2001
Location: Evansville WI
Posts: 9,616
It could be an intermittent open in the motor itself, or another VERY common problem in the 190 is that the harness in the door hinge (inside the rubber conduit) can get brittle and break (broken wires inside the conduit)

Gilly
Reply With Quote
  #3  
Old 08-23-2003, 03:33 AM
azhari
Guest
 
Posts: n/a
Sholin

Check it this thread.It might interest you.

Rebuild your old in-op seat switch !!

It is with regards to the power window switch and how you can check/repair it.

Cheers.
Reply With Quote
  #4  
Old 08-23-2003, 12:31 PM
haasman's Avatar
Registered User
 
Join Date: Jun 2001
Location: San Francisco, CA
Posts: 3,097
I would start by cleaning the switches.

Be VERY gentle with the wood in the console.

Haasman
__________________
'03 E320 Wagon-Sold
'95 E320 Wagon-Went to Ex
'93 190E 2.6-Wrecked
'91 300E-Went to Ex
'65 911 Coupe (#302580)
Reply With Quote
  #5  
Old 08-23-2003, 02:11 PM
Registered User
 
Join Date: Oct 2002
Location: Toronto, Canada
Posts: 700
I just had the same problem happen to me last week. For a minute i thought I burnt out the motor because I rolled up the window while driving and did not notice that the switch got stuck in the down position.

I took apart the door and noticed that two of the rubber mounts that the motor sits on are in pieces and no longer even hold the motor. The window did itself did not present any resistance, just the motor.

I dissasembled everything, lubed up all moving parts and the motor, although still extremely hot, rolled the window up without a problem.

I noticed two plastic caps on the motor, sorta like the ones you have on cases of moving parts so you can lube them, but I doubt this is it, but I am wondering what those are for.

Even now that the window is all lubed up it still seems to be having a hard time rolling up. I still have to clean the switch to make sure that it stops sticking, and at the same time have to replace my deck wiring completely.

xp
__________________
1985 190E 2.3L - a constant project.
Reply With Quote
  #6  
Old 08-23-2003, 02:48 PM
Registered User
 
Join Date: Nov 2000
Location: Mustang, OK
Posts: 509
Thanks for all your replies. The window is working now, but who knows when it will happen again. I'll probably want to disassemble the switches and clean them.

I've got a little experience with this. On my 108, the window switches were melted due to lugging the window motor. In that case, I did dissassemble them and found the problem.

What I had to do there was replace them. On the 108, there are no window relays, just the switches between the battery and the window motor. Is there a window lift relay on the 201? I have the CD-ROM, but could not find alot of info on the wiring of the windows.

Sholin
__________________
What else, '73 MB 280 SEL (Lt Blue)
Daily driver: '84 190D 2.2 5 spd.
Reply With Quote
  #7  
Old 08-24-2003, 04:34 AM
azhari
Guest
 
Posts: n/a
No relays that I know of for the power window switch circuit (checked the Haynes manual electrical schematic).

If you take the switch out and disassemble it, I bet you'll find that the plastic bits which hold the ball bearings in place are cracked causing the intermittent problem.

I had the same problem in mine, intermittently would not go up unless I fiddle the switch.

It eventually failed altogether.

Took it apart and repaired it.

Just replace the switch if in doubt how to repair it.

CHeers.
Reply With Quote
  #8  
Old 08-24-2003, 12:49 PM
haasman's Avatar
Registered User
 
Join Date: Jun 2001
Location: San Francisco, CA
Posts: 3,097
The switch(s) probably do not need to be replaced! Just cleaned.

Search under my name for the procedure. I have done this several times.

The design of the window switches allows dirt to collect and prevent contact. They are easy to take apart and clean and put back together. Just watch out because they have tiny little ball bearings in them which will easily fall to the floor. I recommend taking the switches apart over an old bath towel. That way they won't roll away.

Haasman
__________________
'03 E320 Wagon-Sold
'95 E320 Wagon-Went to Ex
'93 190E 2.6-Wrecked
'91 300E-Went to Ex
'65 911 Coupe (#302580)
Reply With Quote
  #9  
Old 08-24-2003, 10:00 PM
azhari
Guest
 
Posts: n/a
Haasman is spot on about the towel.

I had a bit of fun looking for one ball bearing when it dropped out of the switch, bounced off my shoe and slipped under the car.

What could have been a 15 minute repair job took almost an hour!:p

Cheers and good luck.

Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 06:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page